UC1526 UC2526 UC3526 Regulating Pulse Width Modulator FEATURES DESCRIPTION * 8 To 35V Operation * 5V Reference Trimmed To 1% * 1Hz To 400kHz Oscillator Range * Dual 100mA Source/Sink Outputs * Digital Current Limiting * Double Pulse Suppression * Programmable Deadtime * Under-Voltage Lockout * Single Pulse Metering * Programmable Soft-Start * Wide Current Limit Common Mode Range * TTL/CMOS Compatible Logic Ports The UC1526 is a high performance monolithic pulse width modulator circuit designed for fixed-frequency switching regulators and other power control applications. Included in an 18-pin dual-in-line package are a temperature compensated voltage reference, sawtooth oscillator, error amplifier, pulse width modulator, pulse metering and setting logic, and two low impedance power drivers. Also included are protective features such as soft-start and under-voltage lockout, digital current limiting, double pulse inhibit, a data latch for single pulse metering, adjustable deadtime, and provision for symmetry correction inputs. For ease of interface, all digital control ports are TTL and B-series CMOS compatible. Active LOW logic design allows wired-OR connections for maximum flexibility. This versatile device can be used to implement single-ended or push-pull switching regulators of either polarity, both transformerless and transformer coupled. The UC1526 is characterized for operation over the full military temperature range of -55C to +125C. The UC2526 is characterized for operation from -25C to +85C, and the UC3526 is characterized for operation from 0 to +70C. * Symmetry Correction Capability * Guaranteed 6 Unit Synchronization BLOCK DIAGRAM 6/93 UC1526 UC2526 UC3526 ABSOLUTE MAXIMUM RATINGS (Note 1, 2) RECOMMENDED OPERATING CONDITIONS (Note 3) Input Voltage (+VIN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +40V Collector Supply Voltage (+VC) . . . . . . . . . . . . . . . . . . . . . +40V Logic Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +5.5V Analog Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +VIN Source/Sink Load Current (each output) . . . . . . . . . . . . . 200mA Reference Load Current . . . . . . . . . . . . . . . . . . . . . . . . . . . 50mA Logic Sink Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15mA Power Dissipation at TA = +25C (Note 2) . . . . . . . . . . 1000mW Power Dissipation at TC = +25C (Note 2) . . . . . . . . . . 3000mW Operating Junction Temperature . . . . . . . . . . . . . . . . . . +150C Storage Temperature Range . . . . . . . . . . . . . . -65C to +150C Lead Temperature (soldering, 10 seconds) . . . . . . . . . . +300C Note 1: Values beyond which damage may occur. Note 2: Consult packaging section of databook for thermal limitations and considerations of package. Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +8V to +35V Collector Supply Voltage . . . . . . . . . . . . . . . . . . . +4.5V to +35V Sink/Source Load Current (each output) . . . . . . . . . 0 to 100mA Reference Load Current . . . . . . . . . . . . . . . . . . . . . . 0 to 20mA Oscillator Frequency Range . . . . . . . . . . . . . . . . 1Hz to 400kHz Oscillator Timing Resistor . . . . . . . . . . . . . . . . . . . 2k to 150k Oscillator Timing Capacitor . . . . . . . . . . . . . . . . . . . 1nF to 20F Available Deadtime Range at 40kHz . . . . . . . . . . . . . 3% to 50% Operating Ambient Temperature Range UC1526 . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55C to +125C UC2526 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -25C to +85C UC3526 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0C to +70C Note 3: Range over which the device is functional and parameter limits are guaranteed. CONNECTION DIAGRAMS DIL-18, SOIC-18 (TOP VIEW) J or N Package, DW Package PACKAGE PIN FUNCTION FUNCTION PIN PLCC-20, LCC-20 (TOP VIEW) Q and L Packages N/C +Error -Error Comp. CSS _ _____ Reset - Current Sense + Current Sense _________ Shutdown RTIMING CT RD Sync Output A VC N/C Ground Output B +VIN VREF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 ELECTRICAL CHARACTERISTICS: +VIN = 15V, and over operating ambient temperature, unless otherwise specified, TA = TJ. PARAMETER TEST CONDITIONS UC1526 / UC2526 UC3526 UNITS MIN TYP MAX MIN TYP MAX 4.95 5.00 5.05 4.90 5.00 5.10 V 10 20 10 30 mV Reference Section (Note 4) Output Voltage TJ = + 25C Line Regulation +VIN = 8 to 35V Load Regulation IL = 0 to 20mA 10 30 10 50 mV Temperature Stability Over Operating TJ 15 50 15 50 mV Total Output Voltage Range Over Recommended Operating Conditions 4.90 5.00 5.10 4.85 5.00 5.15 V Short Circuit Current VREF = 0V 25 50 100 25 50 100 mA 0.2 0.4 0.2 0.4 V Under -Voltage Lockout _______ RESET Output Voltage VREF = 3.8V VREF = 4.8V 2.4 Note 4: IL = 0mA. 2 4.8 2.4 4.8 V UC1526 UC2526 UC3526 ELECTRICAL CHARACTERISTICS: +VIN = 15V, and over operating ambient temperature, unless otherwise specified, TA = TJ. PARAMETER TEST CONDITIONS UC1526 / UC2526 MIN TYP MAX UC3526 MIN UNITS TYP MAX Oscillator Section (Note 5) Initial Accuracy TJ = + 25C 3 8 3 8 % Voltage Stability +VIN = 8 to 35V 0.5 1 0.5 1 % Temperature Stability Over Operating TJ 7 10 3 Minimum Frequency RT = 150k , CT = 20 F Maximum Frequency RT = 2k , CT = 1.0nF Sawtooth Peak Voltage +VIN = 35V Sawtooth Valley Voltage +VIN = 8V 1 400 % Hz 400 3.0 0.5 5 1 3.5 1.0 kHz 3.0 0.5 3.5 1.0 V V Error Amplifier Section (Note 6) Input Offset Voltage RS 2k Input Bias Current Input Offset Current 2 5 2 10 mV -350 -1000 -350 -2000 nA 35 100 35 200 nA DC Open Loop Gain RL 10M 64 72 60 72 dB HIGH Output Voltage VPIN1-VPIN2 150mV, ISOURCE = 100 A 3.6 4.2 3.6 4.2 V LOW Output Voltage A VPIN2-VPIN1 150mV, ISINK = 100 Common Mode Rejection Rs 12k 70 94 70 94 dB Supply Voltage Rejection +VIN = 12 to 18V 66 80 66 80 dB 0.2 0.4 0.2 0.4 V PWM Comparator (Note 5) Minimum Duty Cycle VCOMPENSATION = +0.4V Maximum Duty Cycle VCOMPENSATION = +3.6V 0 45 49 2.4 4.0 0 45 49 2.4 4.0 % % Digital Ports (SYNC, SHUTDOWN, and RESET) HIGH Output Voltage ISOURCE =40 A LOW Output Voltage ISINK = 3.6mA HIGH Input Current VIH = +2.4V -125 -200 LOW Input Current VIL = +0.4V -225 -360 100 110 -3 -10 0.2 0.4 0.2 V 0.4 V -125 -200 A -225 -360 A 100 120 mV -3 -10 A Current LImit Comparator (Note 7) Sense Voltage RS 50 90 Input Bias Current 80 Soft-Start Section Error Clamp Voltage RESET = +0.4V Cs Charging Current RESET =+2.4V 0.1 0.4 50 100 150 ISOURCE = 20mA 12.5 13.5 ISOURCE = 100mA 12 0.1 0.4 V 50 100 150 A 12.5 13.5 Output Drivers (Each Output) (Note 8) HIGH Output Voltage LOW Output Voltage 13 ISINK = 20mA 0.2 ISINK = 100mA VC = 40V Rise Time Fall Time ____________ SHUTDOWN = +0.4V Collector Leakage Power Consumption (Note 9) Standby Current 12 V 13 V 0.3 0.2 1.2 2.0 1.2 2.0 V 50 150 50 150 A CL = 1000pF 0.3 0.6 0.3 0.6 s CL = 1000pF 0.1 0.2 0.1 0.2 s 18 30 18 30 mA Note 4: IL = 0mA. Note 5: FOSC = 40kHz (RT = 4.12k 1%, CT = 0.1F 1%, RD = 0) Note 6: VCM = 0 to +5.2V Note 8: VC = +15V Note 9: +VIN = +35V, RT = 4.12k 3 0.3 V UC1526 UC2526 UC3526 APPLICATIONS INFORMATION Voltage Reference The reference regulator of the UC1526 is based on a temperature compensated zener diode. The circuitry is fully active at supply voltages above +8V, and provides up to 20mA of load current to external circuitry at +5.0V. In systems where additional current is required, an external PNP transistor can be used to boost the available current. A rugged low frequency audio-type transistor should be used, and lead lengths between the PWM and transistor should be as short as possible to minimize the risk of oscillations. Even so, some types of transistors may require collector-base capacitance for stability. Up to 1 amp of load current can be obtained with excellent regulation if the device selected maintains high current gain. Figure 2. Under-Voltage Lockout Schematic Soft-Start Circuit The soft-start circuit protects the power transistors and rectifier diodes from high current surges during power supply turn-on. When supply voltage is first applied to the _______ UC1526, the under-voltage lockout circuit holds RESET LOW with Q3. Q1 is turned on, which holds the soft-start capacitor voltage at zero. The second collector of Q1 clamps the output of the error amplifier to ground, guaranteeing zero duty cycle at the driver outputs. When the _______ supply voltage reaches normal operating range, RESET will go HIGH. Q1 turns off, allowing the internal 100mA current source to charge CS. Q2 clamps the error amplifier output to 1VBE above the voltage on CS. As the softstart voltage ramps up to +5V, the duty cycle of the PWM linearly increases to whatever value the voltage regulation loop requires for an error null. Figure 1. Extending Reference Output Current Under-Voltage Lockout The under-voltage lockout circuit protects the UC1526 and the power devices it controls from inadequate supply voltage, If +VIN is too low, the circuit disables the output _______ drivers and holds the RESET pin LOW. This prevents spurious output pulses while the control circuitry is stabilizing, and holds the soft-start timing capacitor in a discharged state. The circuit consists of a +1.2V bandgap reference and comparator circuit which is active when the reference voltage has risen to 3VBE or +1.8V at 25C. When the reference voltage rises to approximately +4.4V, the circuit _______ enables the output drivers and releases the RESET pin, allowing a normal soft-start. The comparator has 200mV of hysteresis to minimize oscillation at the trip point. When +VIN to the PWM is removed and the reference _______ drops to +4.2V, the under-voltage circuit pulls RESET LOW again. The soft-start capacitor is immediately discharged, and the PWM is ready for another soft-start cycle. Figure 3. Soft-Start Circuit Schematic Digital Control Ports The three digital control ports of the UC1526 are bi-directional. Each pin can drive TTL and 5V CMOS logic directly, up to a fan-out of 10 low-power Schottky gates. Each pin can also be directly driven by open-collector The UC1526 can operate from a +5V supply by connecting the VREF pin to the +VIN pin and maintaining the supply between +4.8 and +5.2V. 4 UC1526 UC2526 UC3526 APPLICATIONS INFORMATION (cont.) TTL, open-drain CMOS, and open-collector voltage comparators; fan-in is equivalent to 1 low-power Schottky gate. Each port is normally HIGH; the pin_____ is pulled LOW _ to activate the particular function. Driving SYNC LOW initiates a discharge cycle in the oscillator. Pulling ____________ SHUTDOWN LOW immediately inhibits all PWM output _______ pulses. Holding RESET LOW discharges the soft-start capacitor. The logic threshold is +1.1V at +25C. Noise immunity can be gained at the expense of fan-out with an external 2k pull-up resistor to +5V. Multiple devices can be synchronized together by programming one master unit for the desired frequency and then sharing its sawtooth and clock waveforms with the slave units. All CT terminals ______ are connected to the CT pin of the master, _____ and _all SYNC terminals are likewise connected to the SYNC pin of the master. Slave RT terminals are left open or connected to VREF. Slave RD terminals may be either left open or grounded. Error Amplifier The error amplifier is a transconductance design, with an output impedance of 2M . Since all voltage gain takes place at the output pin, the open-loop gain/frequency characteristics can be controlled with shunt reactance to ground. When compensated for unity-gain stability with 100pF, the amplifier has an open-loop pole at 800Hz. The input connections to the error amplifier are determined by the polarity of the switching supply output voltage. For positive supplies, the common-mode voltage is +5.0V and the feedback connections in Figure 6A are used. With negative supplies, the common-mode voltage is ground and the feedback divider is connected between the negative output and the +5.0V reference voltage, as shown in Figure 6B. Figure 4. Digital Control Port Schematic Oscillator The oscillator is programmed for frequency and dead time with three components: RT, CT and RD. Two waveforms are generated: a sawtooth waveform at pin 10 for pulse width modulation, and a logic clock at pin 12. The following procedure is recommended for choosing timing values: Output Drivers The totem-pole output drivers of the UC1526 are designed to source and sink 100mA continuously and 200mA peak. Loads can be driven either from the output pins 13 and 16, or from the +VC, as required. Since the bottom transistor of the totem-pole is allowed to saturate, there is a momentary conduction path from the +VC terminal to ground during switching. To limit the resulting current spikes a small resistor in series with pin 14 is always recommended. The resistor value is determined by the driver supply voltage, and should be chosen for 200mA peak currents. 1. With RD = 0 (pin 11 shorted to ground) select values for RT and CT from Figure 7 to give the desired oscillator period. Remember that the frequency at each driver output is half the oscillator frequency, and the frequency at the +VC terminal is the same as the oscillator frequency. 2. If more dead time is required, select a large value of RD. At 40kHz dead time increases by 400ns/ . 3. Increasing the dead time will cause the oscillator frequency to decrease slightly. Go back and decrease the value of RT slightly to bring the frequency back to the nominal design value. The UC1526 can be synchronized to an external logic clock by programming the oscillator to free-run at a frequency 10% slower than the sync frequency. A periodic ______ LOW logic pulse approximately 0.5s wide at the SYNC pin will then lock the oscillator to the external frequency. Figure 5. Oscillator Connections and Waveforms 5 UC1526 UC2526 UC3526 Figure 6. Error Amplifier Connections Figure 8. Single-Ended Configuration Figure 7. Push-Pull Configuration Figure 9. Driving N-channel Power Mosfets TYPICAL CHARACTERISTICS Oscillator Period vs RT and CT Oscillation Period 6 UC1526 UC2526 UC3526 TYPICAL CHARACTERISTICS Output Driver Deadtime vs RD Value Under Voltage Lockout Characteristic Error Amplifier Open Loop Gain vs Frequency Current Limit Transfer Function Shutdown Delay Output Driver Saturation Voltage UNITRODE INTEGRATED CIRCUITS 7 CONTINENTAL BLVD. * MERRIMACK, NH 03054 TEL. (603) 424-2410 * FAX (603) 424-3460 7 PACKAGE OPTION ADDENDUM www.ti.com 9-May-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) Samples (Requires Login) 85515012A ACTIVE LCCC FK 20 1 TBD Call TI Call TI 8551501VA ACTIVE CDIP J 18 1 TBD Call TI Call TI UC1526J ACTIVE CDIP J 18 1 TBD A42 N / A for Pkg Type UC1526J883B ACTIVE CDIP J 18 1 TBD A42 N / A for Pkg Type UC1526L883B ACTIVE LCCC FK 20 1 TBD UC2526AJ ACTIVE CDIP J 18 1 TBD UC2526N ACTIVE PDIP N 18 20 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UC2526NG4 ACTIVE PDIP N 18 20 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type POST-PLATE N / A for Pkg Type A42 A42 N / A for Pkg Type UC3526AJ ACTIVE CDIP J 18 1 TBD UC3526DW ACTIVE SOIC DW 18 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR N / A for Pkg Type UC3526DWG4 ACTIVE SOIC DW 18 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC3526DWTR ACTIVE SOIC DW 18 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC3526DWTRG4 ACTIVE SOIC DW 18 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC3526N ACTIVE PDIP N 18 20 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UC3526NG4 ACTIVE PDIP N 18 20 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 9-May-2012 Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF UC1526, UC2526, UC2526AM, UC3526, UC3526AM : * Catalog: UC3526, UC2526A, UC3526M, UC3526A * Military: UC2526M, UC1526, UC1526A NOTE: Qualified Version Definitions: * Catalog - TI's standard catalog product * Military - QML certified for Military and Defense Applications Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device UC3526DWTR Package Package Pins Type Drawing SOIC DW 18 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 2000 330.0 24.4 Pack Materials-Page 1 10.9 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 12.0 2.7 12.0 24.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) UC3526DWTR SOIC DW 18 2000 367.0 367.0 45.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated