• Plated brass bezel finished in bright chrome, black or satin
grey and moulded polycarbonate rear body
MATERIALS
• Max Reverse Voltage: 5 V
• Viewing Angle: 30–100° (dependant on model)
• Life Expectancy: 100,000 hours
• Torque: 75 cNm
• Maximum panel thickness 7 mm
GENERAL SPECIFICATIONS
The company reserves the right to change specifications without notice.
8 mm colored diffused epoxy lens or 8 mm water clear
super bright LEDs
2VDC - 220VAC
(2.8 x 0.8) solder lug/faston terminals, pins or (200 mm long)
wire terminations
DISTINCTIVE FEATURES
• IP67 sealing option (EN60529)
• Operating & Storage Temperature Range:
Rear plastic body: -30 °C to +65° C ( –22 °F to +149 °F)
Rear epoxy body: -40 °C to +85° C ( –40 °F to +185 °F)
ENVIRONMENTAL SPECIFICATIONS
Q12 series
Ø12 mm panel mount LED indicators
MOUNTING
All LED characteristics are dependent upon environmental conditions. Therefore published data
should be considered nominal and subject to variations. 1
LED INDICATORS
IND-Q12-1907R2
Ø12 mm panel mount LED indicators
Q12 series
ELECTRICAL SPECIFICATIONS
Voltage Operating Voltage Operating Current
(Min to Max) (Typical All
Types)
02 (No Resistor) 1.8 to 3.3 VDC 20 mA max
6 VDC 5.4 to 6.6 VDC 20 mA
12 VDC 10.8 to 13.2 VDC 20 mA
24 VDC 21.6 to 26.4 VDC 20 mA
28 VDC 25.2 to 30.8 VDC 20 mA
110 VAC 99 to 121 VAC 6 mA
220 VAC 207 to 235 VAC 3 mA
* Customer to supply resistor for desired operating
current.
LED COMPONENT SPECIFICATIONS
Prominent and
Recessed Flush Forward Voltage
HE Red 350 mcd N/A 2.0 V
Green 60 mcd N/A 2.2 V
Yellow 50 mcd N/A 2.1 V
Blue 800 mcd 330 mcd 3.3 V (Flush : 3.1 V)
White 1,200 mcd 1.560 mcd 3.3 V (Flush : 3.1 V)
Orange 100 mcd N/A 2.2 V
Bi-color (Typical)
(Red/Green) 20/10 mcd N/A 2.0 V/2.2 V
Tri-color (Typical)
(Red/Green/Yellow) 80/15/13 mcd N/A 2.0 V/2.2 V/2.1 V
Bi-color - The color is changed by reversing the polarity of the supply voltage.
Tri-color - The indicator has red and green LEDs, when both connected yellow is
produced.
STANDARD LED INTENSITY
LED COMPONENT SPECIFICATIONS
Prominent and
Recessed Flush Forward Voltage
HE Red 3,000 mcd N/A 2.2 V
Green 8,000 mcd N/A 3.3 V
Yellow 1,100 mcd N/A 2.0 V
Blue 1,500 mcd N/A 3.3 V
White 1,200 mcd N/A 3.3 V
Orange 2,000 mcd N/A 2.2 V
SUPER BRIGHT LED INTENSITY
LED COMPONENT SPECIFICATIONS
Prominent and
Recessed Flush Forward Voltage
HE Red 1,200 mcd 1,120 mcd 2.2 V
Green 2,200 mcd 1,560 mcd 3.3 V
Yellow 1,600 mcd 1,120 mcd 2.0 V
Orange 4,300 mcd 1,120 mcd 2.2 V
HYPER BRIGHT LED INTENSITY
• The operating voltage must not be exceeded by more that
10% as this will result in reduced life expectancy
• Luminous intensity is measured at 20 mA on a discrete led
unless otherwise stated.
• Luminous intensities and color shades of white LEDs may
vary within a batch.
• Luminous intensity will be reduced with lower operating
current.
2
LED INDICATORS
BUILD YOUR PART NUMBER
Ø12 mm panel mount LED indicators
Q12 series
1Solder Lug/ Fastons
(2.8 x 0.8)
2Pins
3Wires
4Rear epoxy Pins
5Rear epoxy Wires
6Short body Pins
7Short body Wires
CBright Chrome
BBlack
GSatin Grey
SERIES
Q
MOUNTING HOLE
12 Ø12 mm PProminent
RRecessed
BEZEL STYLE TERMINALS BEZEL FINISH
LED COLOR
XX Fixed Light
KK Flashing Light
(12 V – 28 VDC)
YY Bi-color
ZZ Tri-color
TYPE OF ILLUMINATION
02 no resistor*
06 6 VDC
12 12 VDC
12A 12 VAC/DC
24 24 VDC
24A 24 VAC/DC
28 28 VDC
28A 28 VAC/DC
110 110 VAC
220 220 VAC
VOLTAGE
(Blank) Unsealed
EIP67
SEALING
RRed
GGreen
YYellow
BBlue
WWhite
OOrange
HR Hyper Bright
Red
HG Hyper Bright
Green
HY Hyper Bright
Yellow
HO Hyper Bright
Orange
SR Super Bright
Red
SG Super Bright
Green
SY Super Bright
Yellow
SB Super Bright
Blue
SW Super Bright
White
SO Super Bright
Orange
RG Red/Green
RY Red/Yellow
GY Green/Yellow
RYG Red/Yellow/
Green
PROMINENT AND RECESSED BEZEL
ABOUT THIS SERIES
Notice: please note that not all combinations of above numbers are available.
• Gold faston terminal denotes anode (+), silver terminal denotes
cathode (-)
• Standard wire length is 200 mm, 24 AWG UL1061, red wire
denotes anode (+), black wire denotes cathode (-) for other wire
lengths consult APEM
• Bi-color leds, by connecting the gold faston (+) one color
is produced, by reversing the supply voltage another color is
produced – bi-colors are available up to 28 VDC
• Take care when soldering to the faston terminals (recommended
solder temperature 300 °C - 3 sec)
• Max voltage for pins and wires is 28 V
• Tri-color are not available with terminal option 1 and behind
panel epoxy sealed with wires (option 4) or pins (option 5).
• 110 VAC and 220 VAC, short body terminal options, 5, 6 and 7
please consult the factory
• We recommend using Hyperbright or Superbright LEDs for use
at 110 VAC and 220 VAC
• The Tri-color LED has red and green LEDs when both are
connected yellow is produced
• Standard tri-color faston terminals are two anodes (+) and one
cathode (-)
• Tri-color wires are one red (+) and one green (+) anode and one
black (-) cathode
• Tri-color pins are center (–) cathode, shortest (+) anode pin
green, longest (+) anode pin red
* please refer to the
forward voltage in
electrical
specifications
3
LED INDICATORS
SERIES
Q
MOUNTING HOLE
12 Ø12 mm FFlush
BEZEL STYLE
1Solder Lug/ Fastons
(2.8 x 0.8)
4Rear epoxy Pins
5Rear epoxy Wires
TERMINALS
CBright Chrome
BBlack
GSatin Grey
BEZEL FINISH
XX Fixed Light
TYPE OF ILLUMINATION
02 no resistor*
06 6 VDC
12 12 VDC
12A 12 VAC/DC
24 24 VDC
24A 24 VAC/DC
28 28 VDC
28A 28 VAC/DC
110 110 VAC
220 220 VAC
VOLTAGE
(Blank) Unsealed
EIP67
SEALING
LED COLOR
HR Red
HG Green
HY Yellow
BBlue
WWhite
HO Orange
FLUSH BEZEL
BUILD YOUR PART NUMBER
Ø12 mm panel mount LED indicators
Q12 series
ABOUT THIS SERIES
Notice: please note that not all combinations of above numbers are available.
• Gold faston terminal denotes anode (+), silver terminal denotes cathode (-)
• Standard wire length is 200 mm, 24 AWG UL1061, red wire denotes anode (+), black wire denotes cathode (-) for other wire lengths
consult APEM
• For leds with alternative voltages please consult Apem
• Take care when soldering to the faston terminals (recommended solder temperature 300 °C - 3 sec)
• Max voltage for pins and wires is 28 V.
• 110VAC and 220VAC only available with solder lug/Faston terminals
4
LED INDICATORS
SOLDER LUG/FASTON
WIRES
REAR EPOXY WIRES
SHORT BODY WIRES
PINS
REAR EPOXY PINS
SHORT BODY PINS
PROMINENT BEZEL
Ø12 mm panel mount LED indicators
Q12 series
5
LED INDICATORS
WIRES
REAR EPOXY WIRES
SHORT BODY WIRES
PINS
REAR EPOXY PINS
SHORT BODY PINS
SOLDER LUG/FASTON
RECESSED BEZEL
Ø12 mm panel mount LED indicators
Q12 series
LED INDICATORS
6
SOLDER LUG/FASTON
REAR EPOXY PINS REAR EPOXY WIRES
FLUSH BEZEL
Ø12 mm panel mount LED indicators
Q12 series
7
LED INDICATORS
