LED INDICATORS IN - 12 -Q D 2 7R 0 19 Q12 series O12 mm panel mount LED indicators DISTINCTIVE FEATURES 8 mm colored diffused epoxy lens or 8 mm water clear super bright LEDs 2VDC - 220VAC (2.8 x 0.8) solder lug/faston terminals, pins or (200 mm long) wire terminations ENVIRONMENTAL SPECIFICATIONS * IP67 sealing option (EN60529) * Operating & Storage Temperature Range: Rear plastic body: -30 C to +65 C ( -22 F to +149 F) Rear epoxy body: -40 C to +85 C ( -40 F to +185 F) GENERAL SPECIFICATIONS * Max Reverse Voltage: 5 V * Viewing Angle: 30-100 (dependant on model) * Life Expectancy: 100,000 hours * Torque: 75 cNm * Maximum panel thickness 7 mm MATERIALS * Plated brass bezel finished in bright chrome, black or satin grey and moulded polycarbonate rear body MOUNTING The company reserves the right to change specifications without notice. All LED characteristics are dependent upon environmental conditions. Therefore published data should be considered nominal and subject to variations. 1 LED INDICATORS Q12 series O12 mm panel mount LED indicators ELECTRICAL SPECIFICATIONS Voltage STANDARD LED INTENSITY LED COMPONENT SPECIFICATIONS Operating Current (Min to Max) (Typical All Types) Prominent and Recessed Flush Forward Voltage 02 (No Resistor) 1.8 to 3.3 VDC 20 mA max HE Red 350 mcd N/A 2.0 V 6 VDC 5.4 to 6.6 VDC 20 mA Green 60 mcd N/A 2.2 V 12 VDC 10.8 to 13.2 VDC 20 mA 24 VDC 21.6 to 26.4 VDC 20 mA Yellow 50 mcd N/A 2.1 V Blue 800 mcd 330 mcd 3.3 V (Flush : 3.1 V) White 1,200 mcd 1.560 mcd 3.3 V (Flush : 3.1 V) Orange 100 mcd N/A 2.2 V Bi-color (Typical) (Red/Green) 20/10 mcd N/A 2.0 V/2.2 V Tri-color (Typical) (Red/Green/Yellow) 80/15/13 mcd N/A 2.0 V/2.2 V/2.1 V Bi-color - The color is changed by reversing the polarity of the supply voltage. Tri-color - The indicator has red and green LEDs, when both connected yellow is produced. SUPER BRIGHT LED INTENSITY LED COMPONENT SPECIFICATIONS Prominent and Recessed Flush Forward Voltage HE Red 3,000 mcd N/A 2.2 V Green 8,000 mcd N/A 3.3 V Yellow 1,100 mcd N/A 2.0 V Blue 1,500 mcd N/A 3.3 V White 1,200 mcd N/A 3.3 V Orange 2,000 mcd N/A 2.2 V HYPER BRIGHT LED INTENSITY LED COMPONENT SPECIFICATIONS HE Red Prominent and Recessed Flush Forward Voltage 1,200 mcd 1,120 mcd 2.2 V Green 2,200 mcd 1,560 mcd 3.3 V Yellow 1,600 mcd 1,120 mcd 2.0 V Orange 4,300 mcd 1,120 mcd 2.2 V * The operating voltage must not be exceeded by more that 10% as this will result in reduced life expectancy * Luminous intensity is measured at 20 mA on a discrete led unless otherwise stated. * Luminous intensities and color shades of white LEDs may vary within a batch. * Luminous intensity will be reduced with lower operating current. 2 Operating Voltage 28 VDC 25.2 to 30.8 VDC 20 mA 110 VAC 99 to 121 VAC 6 mA 220 VAC 207 to 235 VAC 3 mA * Customer to supply resistor for desired operating current. O12 mm panel mount LED indicators BUILD YOUR PART NUMBER PROMINENT AND RECESSED BEZEL Q SERIES BEZEL STYLE MOUNTING HOLE 12 O12 mm P Prominent R Recessed TERMINALS 1 Solder Lug/ Fastons (2.8 x 0.8) 2 Pins 3 Wires 4 Rear epoxy Pins BEZEL FINISH 5 Rear epoxy Wires C Bright Chrome 6 Short body Pins B Black 7 Short body Wires G Satin Grey VOLTAGE LED COLOR TYPE OF ILLUMINATION XX Fixed Light R Red KK Flashing Light (12 V - 28 VDC) G Green YY Bi-color Y Yellow ZZ Tri-color B Blue W O HR White Orange Hyper Bright Red HG Hyper Bright Green SW Super Bright White HY Hyper Bright Yellow SO Super Bright Orange HO Hyper Bright Orange RG Red/Green RY Red/Yellow GY Green/Yellow 02 no resistor* 06 6 VDC 12 12 VDC 12A 24 SG Super Bright Green SY Super Bright Yellow 28A 28 VAC/DC SB Super Bright Blue 110 110 VAC 220 220 VAC RYG ABOUT THIS SERIES 28 E Unsealed IP67 24 VDC Super Bright Red 24A (Blank) 12 VAC/DC SR Red/Yellow/ Green SEALING 24 VAC/DC 28 VDC * please refer to the forward voltage in electrical specifications Notice: please note that not all combinations of above numbers are available. * Gold faston terminal denotes anode (+), silver terminal denotes cathode (-) * 110 VAC and 220 VAC, short body terminal options, 5, 6 and 7 please consult the factory * Standard wire length is 200 mm, 24 AWG UL1061, red wire denotes anode (+), black wire denotes cathode (-) for other wire lengths consult APEM * We recommend using Hyperbright or Superbright LEDs for use at 110 VAC and 220 VAC * Bi-color leds, by connecting the gold faston (+) one color is produced, by reversing the supply voltage another color is produced - bi-colors are available up to 28 VDC * The Tri-color LED has red and green LEDs when both are connected yellow is produced * Standard tri-color faston terminals are two anodes (+) and one cathode (-) * Take care when soldering to the faston terminals (recommended * Tri-color wires are one red (+) and one green (+) anode and one solder temperature 300 C - 3 sec) black (-) cathode * Max voltage for pins and wires is 28 V * Tri-color pins are center (-) cathode, shortest (+) anode pin * Tri-color are not available with terminal option 1 and behind panel epoxy sealed with wires (option 4) or pins (option 5). green, longest (+) anode pin red 3 LED INDICATORS Q12 series LED INDICATORS Q12 series O12 mm panel mount LED indicators BUILD YOUR PART NUMBER FLUSH BEZEL Q SERIES BEZEL STYLE MOUNTING HOLE 12 F O12 mm XX Fixed Light Flush 1 Solder Lug/ Fastons (2.8 x 0.8) 4 Rear epoxy Pins 5 Rear epoxy Wires HR Red 02 no resistor* HG Green 06 6 VDC HY Yellow 12 12 VDC B Blue W White HO Orange C Bright Chrome B Black G Satin Grey VOLTAGE LED COLOR TYPE OF ILLUMINATION BEZEL FINISH TERMINALS 12A 24 24A 28 SEALING (Blank) E Unsealed IP67 12 VAC/DC 24 VDC 24 VAC/DC 28 VDC 28A 28 VAC/DC 110 110 VAC 220 220 VAC ABOUT THIS SERIES Notice: please note that not all combinations of above numbers are available. * Gold faston terminal denotes anode (+), silver terminal denotes cathode (-) * Standard wire length is 200 mm, 24 AWG UL1061, red wire denotes anode (+), black wire denotes cathode (-) for other wire lengths consult APEM * For leds with alternative voltages please consult Apem * Take care when soldering to the faston terminals (recommended solder temperature 300 C - 3 sec) * Max voltage for pins and wires is 28 V. * 110VAC and 220VAC only available with solder lug/Faston terminals 4 O12 mm panel mount LED indicators PROMINENT BEZEL SOLDER LUG/FASTON WIRES PINS REAR EPOXY WIRES REAR EPOXY PINS SHORT BODY WIRES SHORT BODY PINS 5 LED INDICATORS Q12 series LED INDICATORS Q12 series O12 mm panel mount LED indicators RECESSED BEZEL SOLDER LUG/FASTON WIRES PINS REAR EPOXY WIRES REAR EPOXY PINS SHORT BODY WIRES SHORT BODY PINS 6 O12 mm panel mount LED indicators FLUSH BEZEL SOLDER LUG/FASTON REAR EPOXY WIRES REAR EPOXY PINS 7 LED INDICATORS Q12 series