PS2601 AC Power Switch AC Operating Voltage Load Current On-State Voltage Drop PS2601 Units VRMS 1 A VRMS (AT IL = 1A) 1.2 Features * Load Current up to 1A (3A with heat sink) * Blocking Voltages up to 600V * 5mA Sensitivity * Zero-Crossing Detection * DC Control, AC Output * Optically Isolated * TTL and CMOS Compatible * Low EMI and RFI Generation * High Noise Immunity * VDE compatible * Machine Insertable, Wave Solderable Applications * Programmable Control * Process Control * Power Control Panels * Remote Switching * Gas Pump Electronics * Contractors * Large Relays * Solenoids * Motors * Heaters Description PS2601 is an AC Solid State Switch utilizing dual power SCR outputs. This device also includes zero turn on circuitry and is available with a blocking voltage up to 600V. Approvals * UL recognized file #: E69938 * CSA certified file #: LR 43639-8 Ordering Information Part # PS2601 Description 8 Pin SIP (25/Tube) Pin Configuration PS Series Pinout ZC 1 2 - LED + LED DS-PS2601-R9 www.clare.com 6 8 AC Load AC Load 1 PS2601 Absolute Maximum Ratings (@ 25 C) Parameter Min Input Power Dissipation - - 1501 Input Control Current Peak (10ms) - - 50 1 mA A Reverse Input Voltage - - 5 V Total Package Dissipation PS - - Isolation Voltage Input to Output mW 16002 mW 3750 - - VRMS Operational Temperature -40 - +85 C Storage Temperature -40 - +125 C - - +260 +220 C C Soldering Temperature DIP Package Surface Mount Package (10 Seconds Max.) 1 Derate Linearly 1.33 mW/C 2 Derate Linearly 16.6 mW/C Absolute Maximum Ratings are stress ratings. Stresses in excess of these ratings can cause permanent damage to the device. Functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this data sheet is not implied. Exposure of the device to the absolute maximum ratings for an extended period may degrade the device and effect its reliability. Typ Max Units Electrical Characteristics Parameters Conditions Symbol Min Typ Max Units - VDRM - - 600 V Output Characteristics @ 25C Peak Blocking Voltage Load Current (Continuous) VL=120-240VAC IL 0.005 - 1 A Off State Leakage Current VDRM ILEAK - - 1 mA On-State Voltage Drop IL=1A - - 1.2 VRMS - dv/dt 1000 1200 - V/S IF=5 mA IF=5 mA TON TOFF - - 0.5 0.5 cycles cycles - 2 5 V Critical Rate of Rise Switching Speeds Turn-on Turn-off Zero-Cross Turn-On Voltage 1st half cycle Sub. half cycle - - - 1 V 20 - 500 Hz PF 0.25 - - - - - - 3 - pF - IF IF 5 10 - 50 100 mA mA F=5mA VF 0.9 1.2 1.4 V 0.8 - - V VR=5V IR - - 10 uA Operating Frequency1 - Load Power Factor for Guaranteed Turn-On2 - Capacitance Input to Output Input Characteristics @ 25C Input Control Current For Normal Environment For High Noise Environment Input Voltage Drop Input Drop-out Voltage Reverse Input Current Common Characteristics @ 25C Input to Output Capacitance - CI/O - - 3 pF Input to Output Isolation - VI/O 3750 - - VRMS 1 2 2 Zero Cross 1st half cycle @ <100Hz Snubber circuits may be required at low power factors. www.clare.com Rev. 9 PS2601 PERFORMANCE DATA* PS2601 Load Current, Free Air PS2601 Load Current, Heat Sink 1.2 0.8 RJA = 60C/W 0.6 0.4 3 PS with Thermal Clip attached to 3C/W heat sink Peak Surge Current (A) Load Current (A) 1.0 Load Current (A) PS2601 Max. Surge Current (Non-Repetitive) 4 2 PS with Thermal Clip freestanding 1 0.2 15 10 5 0 -40 0 55 85 0 -40 Ambient Temperature (C) 55 NOTE: Values apply to TJ = 50C before Surge 20 85 16 Ambient Temperature (C) PS2601 Typical Forward Voltage vs. Temperature 50 100 Pulse Duration (ms) PS2601 dv/dt Method PS2601 Typical dv/dt vs. Temperature Critical Rate of Rise (V/s) Forward Voltage (V) 2.0 1.5 1.0 0.5 10 25 50 75 100 125 Ambient Temperature (C) 150 Vo 1200 1000 800 Vo = 300V dv 0.63 x 300V dt RC 63% 600 In accordance with EIA/NARM Standards RS-443 for Solid State Relays 400 10% 200 0 25 50 Ambient Temperature (C) 85 189 RC RC The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application department. Rev. 9 www.clare.com 3 PS2601 Mechanical Dimensions 8 Pin SIP 3.302 .051 (.130 .002) 19.202 .381 (.756 .015) 8.99 (.354) 6.350 TYP. (.250) 3.30 (.130) 5.944 TYP. (.234) 10.160 (.400) 5.080 (.200) .508 TYP. (.020) Dimensions mm (inches) 4 www.clare.com Rev. 9 For additional information please visit our website at: www.clare.com Clare, Inc. makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any time without notice. Neither circuit patent licenses nor indemnity are expressed or implied. Except as set forth in Clare's Standard Terms and Conditions of Sale, Clare, Inc. assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right. The products described in this document are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body, or in other applications intended to support or sustain life, or where malfunction of Clare's product may result in direct physical harm, injury, or death to a person or severe property or environmental damage. Clare, Inc. reserves the right to discontinue or make changes to its products at any time without notice. Specification: DS-PS2601-R9.0 (c)Copyright 2002, Clare, Inc. All rights reserved. Printed in USA. 6/25/02