1N5391GP THRU 1N5399GP
GLASS PASSIVATED JUNCTION RECTIFIER
Reverse Voltage
-
50 to 1000 Volts Forward Current - 1.5 Amperes
FEATURES
♦ Plastic package has
Underwriters Laborator y
Flammability Classification 94V-0
♦ High temperature metallurgically
bonded construction
♦ Glass passivated cavity-free junction
♦ Capable of meeting environmental standards of
MIL-S-19500
♦ 1.5 Ampere operation at TA=70°C with no
thermal r unaway
♦ Typical IRless than 0.1µA
♦ High temperature soldering guaranteed:
350°C/10 seconds, 0.375" (9.5mm) lead length,
5 lbs. (2.3kg) tension
MECHANICAL DATA
Case: JEDEC DO-204AC molded plastic over glass body
Terminals: Plated axial leads, solderable per MIL-STD-750,
Method 2026
Polarity: Color band denotes cathode end
Mounting Position: Any
Weight: 0.015 ounce, 0.4 gram
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25°C ambient temperature unless otherwise specified.
1N53 1N53 1N53 1N53 1N53 1N53 1N53 1N53 1N53
SYMBOLS 91GP 92GP 93GP 94GP 95GP 96GP 97GP 98GP 99GP UNITS
* Maximum repetitive peak reverse voltage VRRM 50 100 200 300 400 500 600 800 1000 Volts
* Maximum RMS voltage VRMS 35 70 140 210 280 350 420 560 700 Volts
* Maximum DC blocking voltage VDC 50 100 200 300 400 500 600 800 1000 Volts
* Maximum average forward rectified current
0.375" (9.5mm) lead length at TL=70°C I(AV) 1.5 Amps
* Peak forward surge current
8.3ms single half sine-wave superimposed
on rated load (JEDEC Method) IFSM 50.0 Amps
* Maximum instantaneous forward voltage
at 1.5A, TA=70°C VF1.4 Volts
*Maximum DC reverse current TA=25°C 5.0
at rated DC blocking voltage TA=150°C IR300.0 µA
* Maximum full load reverse current
full cycle average, 0 375" (9.5mm) IR(AV) 300.0 µA
lead length at TA=70°C
Typical reverse recover y time (NOTE 1) trr 2.0 µs
Typical junction capacitance (NOTE 2) CJ15.0 pF
Typical ther mal resistance (NOTE 3) RΘJA 45.0 °C/W
*Operating junction and storage temperature range TJ, TSTG -65 to +175 °C
NOTES:
(1) Reverse recovery test condition: IF=0.5A, IR=1.0A, Irr=0.25A
(2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts
(3) Ther mal resistance from junction to ambient at 0.375" (9.5mm) lead length, P.C.B. mounted
* JEDEC registered values
4/98
0.034 (0.86)
0.028 (0.71)
0.140 (3.6)
0.104 (2.6)
DIA.
DIA.
1.0
MIN.
(25.4)
0.230 (5.8)
0.300 (7.6)
1.0
MIN.
(25.4)
DO-204AC
Dimensions in inches and (millimeters)
*
Glass-plastic encapsulation technique is covered by
Patent No. 3,996,602 and brazed-lead assembly by Patent No. 3,930,306
®
PATENTED*
0.4 0.6 0.8 1.0 1.2 1.4 1.6
0.01
0.1
1
10
2.0
25 50 75 100 150 175
0.5
1.0
0
0125
100
10
1110100
110 100
0
10
30
50
40
20
020406080100
0.01
0.1
1
10
0.01 0.1 1 10 100
0.1
1
10
100
RATINGS AND CHARACTERISTIC CURVES 1N5391GP THRU 1N5399GP
FIG. 1 - FORWARD CURRENT DERATING CURVE
TEMPERATURE, °C
AVERAGE FORWARD RECTIFIED CURRENT,
AMPERES
FIG. 2 - MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT
NUMBER OF CYCLES AT 60 HZ
PEAK FORWARD SURGE CURRENT,
AMPERES
FIG. 3 - TYPICAL INSTANTANEOUS
FORWARD CHARACTERISTICS FIG. 4 - TYPICAL REVERSE
CHARACTERISTICS
INSTANTANEOUS FORWARD CURRENT,
AMPERES
INSTANTANEOUS REVERSE CURRENT,
MICROAMPERES
INSTANTANEOUS FORWARD VOLTAGE,
VOLTS
PERCENT OF RATED PEAK REVERSE
VOLTAGE, %
FIG. 5 - TYPICAL JUNCTION CAPACITANCE
JUNCTION CAPACITANCE, pF
REVERSE V OLTAGE, V OLTS
TJ=TJmax.
8.3ms SINGLE HALF SINE-WAVE
(JEDEC Method)
TJ=125°C
TJ=25°C
TJ=25°C
PULSE WIDTH=300µs
1% DUTY CYCLE
TJ=25°C
f=1.0 MHZ
Vsig=50mVp-p
0.375" (9.5mm) LEAD LENGTH
TA, AMBIENT
TEMPERATURE
TL, LEAD
TEMPERATURE
TJ=75°C
60 HZ
RESISTIVE OR
INDUCTIVE LOAD
FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE
TRANSIENT THERMAL IMPEDANCE (°C/W)
t, PULSE DURATION, sec
