SN54LVT573, SN74LVT573 3.3-V ABT OCTAL TRANSPARENT D-TYPE LATCHES WITH 3-STATE OUTPUTS SCBS138D - MAY 1992 - REVISED JULY 1995 D D D D D D OE 1D 2D 3D 4D 5D 6D 7D 8D GND 1 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 VCC 1Q 2Q 3Q 4Q 5Q 6Q 7Q 8Q LE SN54LVT573 . . . FK PACKAGE (TOP VIEW) 3D 4D 5D 6D 7D 1Q D SN54LVT573 . . . J OR W PACKAGE SN74LVT573 . . . DB, DW, OR PW PACKAGE (TOP VIEW) 2D 1D OE VCC D State-of-the-Art Advanced BiCMOS Technology (ABT) Design for 3.3-V Operation and Low Static Power Dissipation Support Mixed-Mode Signal Operation (5-V Input and Output Voltages With 3.3-V VCC) Support Unregulated Battery Operation Down to 2.7 V Typical VOLP (Output Ground Bounce) < 0.8 V at VCC = 3.3 V, TA = 25C ESD Protection Exceeds 2000 V Per MIL-STD-883C, Method 3015; Exceeds 200 V Using Machine Model (C = 200 pF, R = 0) Latch-Up Performance Exceeds 500 mA Per JEDEC Standard JESD-17 Bus-Hold Data Inputs Eliminate the Need for External Pullup Resistors Support Live Insertion Package Options Include Plastic Small-Outline (DW), Shrink Small-Outline (DB), and Thin Shrink Small-Outline (PW) Packages, Ceramic Chip Carriers (FK), Ceramic Flat (W) Packages, and Ceramic (J) DIPs 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 2Q 3Q 4Q 5Q 6Q 8D GND LE 8Q 7Q D description These octal latches are designed specifically for low-voltage (3.3-V) VCC operation, but with the capability to provide a TTL interface to a 5-V system environment. The eight latches of the 'LVT573 are transparent D-type latches. While the latch-enable (LE) input is high, the Q outputs follow the data (D) inputs. When LE is taken low, the Q outputs are latched at the logic levels set up at the D inputs. A buffered output-enable (OE) input can be used to place the eight outputs in either a normal logic state (high or low logic levels) or a high-impedance state. In the high-impedance state, the outputs neither load nor drive the bus lines significantly. The high-impedance state and increased drive provide the capability to drive bus lines without need for interface or pullup components. OE does not affect the internal operations of the latches. Old data can be retained or new data can be entered while the outputs are in the high-impedance state. Active bus-hold circuitry is provided to hold unused or floating data inputs at a valid logic level. To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. The SN74LVT573 is available in TI's shrink small-outline package (DB), which provides the same I/O pin count and functionality of standard small-outline packages in less than half the printed-circuit-board area. The SN54LVT573 is characterized for operation over the full military temperature range of - 55C to 125C. The SN74LVT573 is characterized for operation from - 40C to 85C. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 1995, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 SN54LVT573, SN74LVT573 3.3-V ABT OCTAL TRANSPARENT D-TYPE LATCHES WITH 3-STATE OUTPUTS SCBS138D - MAY 1992 - REVISED JULY 1995 FUNCTION TABLE (each latch) INPUTS OE LE D OUTPUT Q L H H H L H L L L L X Q0 H X X Z logic symbol OE LE 1D 2D 3D 4D 5D 6D 7D 8D 1 11 2 logic diagram (positive logic) EN OE C1 1D 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 LE 1 11 1Q C1 2Q 3Q 1D 2 19 1Q 1D 4Q 5Q 6Q 7Q To Seven Other Channels 8Q This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 0.5 V to 4.6 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 0.5 V to 7 V Voltage range applied to any output in the high state or power-off state, VO (see Note 1) . . . . - 0.5 V to 7 V Current into any output in the low state, IO: SN54LVT573 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 mA SN74LVT573 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 mA Current into any output in the high state, IO (see Note 2): SN54LVT573 . . . . . . . . . . . . . . . . . . . . . . . . . 48 mA SN74LVT573 . . . . . . . . . . . . . . . . . . . . . . . . . 64 mA Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 50 mA Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 50 mA Maximum power dissipation at TA = 55C (in still air) (see Note 3): DB package . . . . . . . . . . . . . . . . . . . . 0.6 W DW package . . . . . . . . . . . . . . . . . . . 1.6 W PW package . . . . . . . . . . . . . . . . . . . 0.7 W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65C to 150C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. 2. This current flows only when the output is in the high state and VO > VCC. 3. The maximum package power dissipation is calculated using a junction temperature of 150C and a board trace length of 750 mils. For more information, refer to the Package Thermal Considerations application note in the 1994 ABT Advanced BiCMOS Technology Data Book, literature number SCBD002B. 2 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN54LVT573, SN74LVT573 3.3-V ABT OCTAL TRANSPARENT D-TYPE LATCHES WITH 3-STATE OUTPUTS SCBS138D - MAY 1992 - REVISED JULY 1995 recommended operating conditions (see Note 4) SN54LVT573 SN74LVT573 MIN MAX MIN MAX 2.7 3.6 2.7 3.6 UNIT VCC VIH Supply voltage VIL VI Low-level input voltage 0.8 0.8 Input voltage 5.5 5.5 V IOH IOL High-level output current - 24 - 32 mA 48 64 mA t /v Input transition rise or fall rate 10 10 ns / V 85 C High-level input voltage 2 Low-level output current Outputs enabled TA Operating free-air temperature NOTE 4: Unused control inputs must be held high or low to prevent them from floating. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 - 55 2 125 - 40 V V V 3 SN54LVT573, SN74LVT573 3.3-V ABT OCTAL TRANSPARENT D-TYPE LATCHES WITH 3-STATE OUTPUTS SCBS138D - MAY 1992 - REVISED JULY 1995 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VIK VOH VCC = 2.7 V, VCC = MIN to MAX, II = -18 mA IOH = -100 A VCC = 2.7 V, IOH = - 8 mA IOH = - 24 mA VCC = 3 V VCC = 2 2.7 7V VOL VCC = 3 V VCC = 0 or MAX, 36V VCC = 3.6 Ioff VCC = 0, II(hold) I(h ld) VCC = 3 V IOZH IOZL VCC = 3.6 V, VCC = 3.6 V, VCC = 3.6 V, VI = VCC or GND ICC MIN SN74LVT573 TYP MAX MIN -1.2 VCC - 0.2 2.4 -1.2 VCC - 0.2 2.4 0.2 IOL = 24 mA IOL = 16 mA 0.5 0.5 0.4 0.4 IOL = 32 mA IOL = 48 mA 0.5 0.5 VI = 2 V VO = 3 V 0.55 Control inputs Data inputs 50 10 1 1 1 1 -5 -5 100 Data inputs 75 75 -75 -75 VO = 0.5 V IO = 0, V 0.55 IOL = 64 mA VI = 5.5 V VI or VO = 0 to 4.5 V VI = 0.8 V V 2 0.2 VI = VCC VI = 0 UNIT V 2 IOH = - 32 mA IOL = 100 A VI = VCC or GND II SN54LVT573 TYP MAX TEST CONDITIONS 1 1 A -1 -1 A 0.13 0.39 0.13 0.19 Outputs low 8.6 14 8.6 12 0.13 0.39 0.13 0.19 ICC VCC = 3 V to 3.6 V, One input at VCC - 0.6 V, Other inputs at VCC or GND Ci VI = 3 V or 0 VO = 3 V or 0 A A Outputs high Outputs disabled A 0.3 0.2 4 Co 8 All typical values are at VCC = 3.3 V, TA = 25C. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions. This is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND. mA mA 4 pF 8 pF timing requirements over recommended operating free-air temperature range (unless otherwise noted) (see Figure 1) SN54LVT573 VCC = 3.3 V 0.3 V MIN tw tsu Pulse duration, LE high th Hold time, data after LE 4 MAX SN74LVT573 VCC = 2.7 V MIN MAX VCC = 3.3 V 0.3 V MIN MAX VCC = 2.7 V MIN UNIT MAX 3.3 3.3 3.3 3.3 ns 1 0.9 0.7 0.6 ns 1.8 2 1.6 1.8 ns Setup time, data before LE POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN54LVT573, SN74LVT573 3.3-V ABT OCTAL TRANSPARENT D-TYPE LATCHES WITH 3-STATE OUTPUTS SCBS138D - MAY 1992 - REVISED JULY 1995 switching characteristics over recommended operating free-air temperature range, CL = 50 pF (unless otherwise noted) (see Figure 1) SN54LVT573 PARAMETER FROM (INPUT) TO (OUTPUT) tPLH tPHL D Q tPLH tPHL LE Q tPZH tPZL OE Q tPHZ tPLZ OE Q VCC = 3.3 V 0.3 V SN74LVT573 VCC = 2.7 V MIN MAX VCC = 3.3 V 0.3 V MIN TYP MAX VCC = 2.7 V MIN MAX MIN 0.5 4.7 4.9 1 2.5 4.2 4.7 0.5 4.9 5.4 1 2.7 4.3 5.2 1 6 6.9 1.6 3.5 5.6 6.3 1.4 6.9 7.6 2.5 4.3 6.5 7.2 0.5 5.3 6.4 1 2.8 5.1 6.2 0.7 5.7 7.2 1.3 3.3 5.5 6.6 1.2 5.9 6.9 2 3.7 5.7 6.7 1 5.4 5.5 1.5 3 4.6 5.1 UNIT MAX ns ns ns ns All typical values are at VCC = 3.3 V, TA = 25C. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 5 SN54LVT573, SN74LVT573 3.3-V ABT OCTAL TRANSPARENT D-TYPE LATCHES WITH 3-STATE OUTPUTS SCBS138D - MAY 1992 - REVISED JULY 1995 PARAMETER MEASUREMENT INFORMATION 6V S1 500 From Output Under Test Open GND CL = 50 pF (see Note A) TEST S1 tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open 6V GND 500 2.7 V LOAD CIRCUIT FOR OUTPUTS 1.5 V Timing Input 0V tw tsu 2.7 V Input 1.5 V 1.5 V th 2.7 V 1.5 V Data Input 1.5 V 0V 0V VOLTAGE WAVEFORMS PULSE DURATION VOLTAGE WAVEFORMS SETUP AND HOLD TIMES 2.7 V 1.5 V Input 1.5 V 0V VOH 1.5 V Output 1.5 V VOL tPLH tPHL VOH Output 1.5 V 1.5 V VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES INVERTING AND NONINVERTING OUTPUTS 1.5 V 1.5 V 0V tPZL tPHL tPLH 2.7 V Output Control tPLZ Output Waveform 1 S1 at 6 V (see Note B) Output Waveform 2 S1 at GND (see Note B) 1.5 V tPZH 3V VOL + 0.3 V VOL tPHZ 1.5 V VOH - 0.3 V VOH [0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES LOW- AND HIGH-LEVEL ENABLING NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR 10 MHz, ZO = 50 , tr 2.5 ns, tf 2.5 ns. D. The outputs are measured one at a time with one transition per measurement. Figure 1. Load Circuit and Voltage Waveforms 6 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 PACKAGE OPTION ADDENDUM www.ti.com 8-Dec-2005 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty SN74LVT573DBLE OBSOLETE SSOP DB 20 SN74LVT573DBR NRND SSOP DB 20 SN74LVT573DBRE4 ACTIVE SSOP DB 20 SN74LVT573DW NRND SOIC DW 20 SN74LVT573DWE4 ACTIVE SOIC DW 20 SN74LVT573DWR NRND SOIC DW 20 SN74LVT573DWRE4 ACTIVE SOIC DW 20 TBD Call TI Call TI SN74LVT573NSR OBSOLETE SO NS 20 TBD Call TI Call TI SN74LVT573PWLE OBSOLETE TSSOP PW 20 TBD Call TI Call TI SN74LVT573PWR NRND TSSOP PW 20 SN74LVT573PWRE4 ACTIVE TSSOP PW 20 TBD Call TI Call TI SNJ54LVT573FK OBSOLETE LCCC FK 20 TBD Call TI Call TI SNJ54LVT573J OBSOLETE CDIP J 20 TBD Call TI Call TI SNJ54LVT573W OBSOLETE CFP W 20 TBD Call TI Call TI TBD 2000 Green (RoHS & no Sb/Br) 25 Lead/Ball Finish Call TI CU NIPDAU TBD Call TI Green (RoHS & no Sb/Br) CU NIPDAU TBD 2000 Green (RoHS & no Sb/Br) 2000 Green (RoHS & no Sb/Br) Call TI CU NIPDAU CU NIPDAU MSL Peak Temp (3) Call TI Level-1-260C-UNLIM Call TI Level-1-260C-UNLIM Call TI Level-1-260C-UNLIM Level-1-260C-UNLIM (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 MECHANICAL DATA MLCC006B - OCTOBER 1996 FK (S-CQCC-N**) LEADLESS CERAMIC CHIP CARRIER 28 TERMINAL SHOWN 18 17 16 15 14 13 NO. OF TERMINALS ** 12 19 11 20 10 A B MIN MAX MIN MAX 20 0.342 (8,69) 0.358 (9,09) 0.307 (7,80) 0.358 (9,09) 28 0.442 (11,23) 0.458 (11,63) 0.406 (10,31) 0.458 (11,63) 21 9 22 8 44 0.640 (16,26) 0.660 (16,76) 0.495 (12,58) 0.560 (14,22) 23 7 52 0.739 (18,78) 0.761 (19,32) 0.495 (12,58) 0.560 (14,22) 24 6 68 0.938 (23,83) 0.962 (24,43) 0.850 (21,6) 0.858 (21,8) 84 1.141 (28,99) 1.165 (29,59) 1.047 (26,6) 1.063 (27,0) B SQ A SQ 25 5 26 27 28 1 2 3 4 0.080 (2,03) 0.064 (1,63) 0.020 (0,51) 0.010 (0,25) 0.020 (0,51) 0.010 (0,25) 0.055 (1,40) 0.045 (1,14) 0.045 (1,14) 0.035 (0,89) 0.045 (1,14) 0.035 (0,89) 0.028 (0,71) 0.022 (0,54) 0.050 (1,27) 4040140 / D 10/96 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. This package can be hermetically sealed with a metal lid. The terminals are gold plated. Falls within JEDEC MS-004 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 MECHANICAL DATA MSSO002E - JANUARY 1995 - REVISED DECEMBER 2001 DB (R-PDSO-G**) PLASTIC SMALL-OUTLINE 28 PINS SHOWN 0,38 0,22 0,65 28 0,15 M 15 0,25 0,09 8,20 7,40 5,60 5,00 Gage Plane 1 14 0,25 A 0-8 0,95 0,55 Seating Plane 2,00 MAX 0,10 0,05 MIN PINS ** 14 16 20 24 28 30 38 A MAX 6,50 6,50 7,50 8,50 10,50 10,50 12,90 A MIN 5,90 5,90 6,90 7,90 9,90 9,90 12,30 DIM 4040065 /E 12/01 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-150 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 MECHANICAL DATA MTSS001C - JANUARY 1995 - REVISED FEBRUARY 1999 PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 14 PINS SHOWN 0,30 0,19 0,65 14 0,10 M 8 0,15 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 1 7 0- 8 A 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 8 14 16 20 24 28 A MAX 3,10 5,10 5,10 6,60 7,90 9,80 A MIN 2,90 4,90 4,90 6,40 7,70 9,60 DIM 4040064/F 01/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-153 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2005, Texas Instruments Incorporated