TPS61130 TPS61131 TPS61132 www.ti.com SLVS431B - JUNE 2002 - REVISED JANUARY 2008 SYNCHRONOUS SEPIC / FLYBACK CONVERTER WITH 1.1A SWITCH AND INTEGRATED LDO FEATURES APPLICATIONS * Synchronous, Up To 90% Efficient, SEPIC Converter With 300-mA Output Current From 2.5-V Input * Integrated 200-mA Reverse Voltage Protected LDO for DC/DC Output Voltage Post Regulation or Second Output Voltage * 40-A (Typical) Quiescent Current * Input Voltage Range: 1.8-V to 5.5-V * Fixed and Adjustable Output Voltage Options up to 5.5-V * Power Save Mode for Improved Efficiency at Low Output Power * Low Battery Comparator * Power Good Output * Low EMI-Converter (Integrated Antiringing Switch) * Load Disconnect During Shutdown * Overtemperature Protection * Available in a Small 4mm x 4mm QFN-16 or in a TSSOP-16 Package * 1 2 * * All Single Cell Li, Dual or Triple Cell Battery or USB Powered Products as MP-3 Player, PDAs, and Other Portable Equipment Dual Input or Dual Output Mode High Efficient Li-Ion to 3.3-V Conversion DESCRIPTION The TPS6113x devices provide a complete power supply solution for products powered by either a one-cell Li-Ion or Li-Polymer, or two- to four-cell Alkaline, NiCd, or NiMH batteries. The devices can generate two regulated output voltages. It provides a simple and efficient buck-boost solution for generating 3.3 V out of an input voltage that can be both higher and lower than the output voltage. The converter provides a maximum output current of at least 300 mA with supply voltages down to 1.8 V. The implemented SEPIC converter is based on a fixed frequency, pulse-width-modulation (PWM) controller using a synchronous rectifier to obtain maximum efficiency. The maximum peak current in the SEPIC switch is limited to a value of 1600 mA. 22 mH SWN VBAT 1.8 V up to 6 V Input 10 mF SWP VOUT LBI TPS61130 FB Control Inputs OFF ON OFF ON OFF ON SKIPEN PGOOD LBO EN 10 mF 22 mH VOut1 e.g. 3.3 V up to 300 mA 100 mF Control Outputs LDOIN LDOEN GND LDOOUT PGND LDOSENSE VOut2 e.g. 1.5 V up to 300 mA 2.2 mF 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PowerPAD is a trademark of Texas Instruments. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2002-2008, Texas Instruments Incorporated TPS61130 TPS61131 TPS61132 www.ti.com SLVS431B - JUNE 2002 - REVISED JANUARY 2008 Description (continued) The converter can be disabled to minimize battery drain. During shutdown, the load is completely disconnected from the battery. A low-EMI mode is implemented to reduce ringing, and in effect, lower radiated electromagnetic energy when the converter enters the discontinuous conduction mode. A power good output at the SEPIC stage provides additional control of any connected circuits like cascaded power supply stages, or microprocessors. The built-in LDO can be used for a second output voltage derived either from the SEPIC output or directly from the battery. The output voltage of this LDO can be programmed by an external resistor divider or is fixed internally on the chip. The LDO can be enabled separately, i.e., using the power good of the SEPIC stage. The device is packaged in a 16-pin QFN package measuring 4 mm x 4 mm (RSA) or in a 16-pin TSSOP (PW) package. AVAILABLE OUTPUT VOLTAGE OPTIONS (1) TA 40C to 85C (1) (2) OUTPUT VOLTAGE DC/DC OUTPUT VOLTAGE LDO Adjustable Adjustable 3.3 V 3.3 V 3.3 V 1.5 V Adjustable Adjustable 3.3 V 1.5 V PART NUMBER (2) PACKAGE TPS61130PW 16-Pin TSSOP TPS61131PW TPS61132PW TPS61130RSA 16-Pin QFN TPS61132RSA Contact the factory to check availability of other fixed output voltage versions. The packages are available taped and reeled. Add R suffix to device type (e.g., TPS61130PWR or TPS61130RSAR) to order quantities of 2000 devices per reel for the TSSOP (PW) package and 3000 devices per reel for the QFN (RSA) package. ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range (unless otherwise noted) (1) TPS61130 TPS61131 TPS61132 Input voltage range on FB -0.3 V to 3.6 V Input voltage range on SWN -0.3 V to 12 V Input voltage range on SWP -7.0 V to 7.0 V Maximum voltage between SWP and VOUT -12 V Input voltage range on VOUT, LDOIN, LDOOUT, LDOEN, LDOSENSE, PGOOD, LBO, VBAT, LBI, SKIPEN, EN -0.3 V to 7 V Operating virtual junction temperature TJ -40C to 150C Storage temperature range Tstg -65C to 150C (1) Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. RECOMMENDED OPERATING CONDITIONS MIN Supply voltage at VBAT 1.8 Operating free air temperature range, TA Operating virtual junction temperature, TJ 2 Submit Documentation Feedback NOM MAX UNIT 6.5 V -40 85 C -40 125 C Copyright (c) 2002-2008, Texas Instruments Incorporated Product Folder Link(s): TPS61130 TPS61131 TPS61132 TPS61130 TPS61131 TPS61132 www.ti.com SLVS431B - JUNE 2002 - REVISED JANUARY 2008 ELECTRICAL CHARACTERISTICS over recommended free-air temperature range and over recommended input voltage range (typical at an ambient temperature range of 25C) (unless otherwise noted) DC/DC STAGE PARAMETER TEST CONDITIONS MIN TYP MAX UNIT VI Input voltage range 1.8 6.5 V VO Adjustable output voltage range (TPS61130) 2.5 5.5 V Vref Reference voltage 485 500 515 mV f Oscillator frequency 400 500 600 kHz ISW Switch current limit 1300 1600 mA VOUT= 3.3 V 1100 Startup current limit 0.4 x ISW VOUT= 3.3 V 200 350 m SWP switch on resistance VOUT= 3.3 V 250 500 m 3 % Total accuracy (including line and load regulation) DC/DC quiescent current into VBAT IO= 0 mA, VEN = VBAT = 1.8 V, VOUT = 3.3 V, ENLDO = 0 V 10 25 A into VOUT IO = 0 mA, VEN = VBAT = 1.8 V, VOUT = 3.3 V, ENLDO = 0 V 10 25 A VEN= 0 V 0.2 1 A TYP MAX DC/DC shutdown current LDO STAGE mA SWN switch on resistance PARAMETER TEST CONDITIONS MIN UNIT VI(LDO) Input voltage range 1.8 7 V VO(LDO) Adjustable output voltage range (TPS61130) 0.9 5.5 V IO(max) Output current 200 320 LDO short circuit current limit CONTROL STAGE VIL mA 500 mA 300 mV Minimum voltage drop IO =200 mA Total accuracy (including line and load regulation) IO 1 mA 3% Line regulation LDOIN change from 1.8 V to 2.6 V at 100 mA, LDOOUT = 1.5 V 0.6% Load regulation Load change from 10% to 90%, LDOIN = 3.3 V 0.6% LDO quiescent current LDOIN = 7 V, VBAT = 1.8 V, EN = VBAT LDO shutdown current LDOEN = 0 V, LDOIN = 7 V PARAMETER TEST CONDITIONS LBI voltage threshold VLBI voltage decreasing 20 30 A A 0.1 1 MIN TYP MAX UNIT 490 500 510 mV LBI input hysteresis 10 mV LBI input current EN = VBAT or GND 0.01 0.1 A LBO output low voltage VO = 3.3 V, IOI = 100 A 0.04 0.4 V VLBO = 7 V 0.01 LBO output low current LBO output leakage current VIL EN, SKIPEN input low voltage VIH EN, SKIPEN input high voltage VIL LDOEN input low voltage VIH LDOEN input high voltage A 100 0.1 A 0.2 x VBAT V 0.8 x VBAT V 0.2 x VLDOIN 0.8 x VLDOIN Copyright (c) 2002-2008, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TPS61130 TPS61131 TPS61132 V V 3 TPS61130 TPS61131 TPS61132 www.ti.com SLVS431B - JUNE 2002 - REVISED JANUARY 2008 ELECTRICAL CHARACTERISTICS (continued) over recommended free-air temperature range and over recommended input voltage range (typical at an ambient temperature range of 25C) (unless otherwise noted) CONTROL STAGE (continued) PARAMETER TEST CONDITIONS EN, SKIPEN input current Clamped on GND or VBAT Power-Good threshold VO = 3.3 V MIN 0.9 x Vo Power-Good delay TYP MAX 0.01 0.1 UNIT A 0.92 x Vo 0.95 x Vo V s 30 Power-Good output low voltage VO = 3.3 V, IOI = 100A 0.04 Power-Good output low current 0.4 A 100 Power-Good output leakage current VPG = 7 V 0.01 V 0.1 A Over-Temperature protection 140 C Over-Temperature hysteresis 20 C PIN ASSIGNMENTS PW PACKAGE (TOP VIEW) 4 16 15 14 13 12 11 10 9 Submit Documentation Feedback VOUT FB PGOOD LBO GND LDOSENSE LDOOUT LDOIN SWN SWP VOUT FB 1 2 3 4 5 6 7 8 PGND VBAT LBI SKIPEN PGOOD LBO GND LDOSENSE EN LDOEN LDOIN LDOOUT SWP SWN PGND VBAT LBI SKIPEN EN LDOEN RSA PACKAGE (TOP VIEW) Copyright (c) 2002-2008, Texas Instruments Incorporated Product Folder Link(s): TPS61130 TPS61131 TPS61132 TPS61130 TPS61131 TPS61132 www.ti.com SLVS431B - JUNE 2002 - REVISED JANUARY 2008 Terminal Functions TERMINAL NAME NO. PW I/O DESCRIPTION RSA EN 7 5 I DC/DC-enable input. (1/VBAT enabled, 0/GND disabled) FB 15 13 I DC/DC voltage feedback of adjustable versions GND 12 10 LBI 5 3 I Low battery comparator input (comparator enabled with EN) LBO 13 11 O Low battery comparator output (open drain) LDOEN 8 6 I LDO-enable input (1/LDOIN enabled, 0/GND disabled) LDOOUT 10 8 O LDO output LDOIN 9 7 I LDO input LDOSENSE 11 9 I LDO feedback for voltage adjustment, must be connected to LDOOUT at fixed output voltage versions Control/logic ground PGND 3 1 PGOOD 14 12 O Power ground DC/DC output power good (1 : good, 0 : failure) (open drain) SKIPEN 6 4 I Enable/disable power save mode (1/VBAT enabled, 0/GND disabled) SWN 2 16 I DC/DC switch input SWP 1 15 I DC/DC rectifying switch input VBAT 4 2 I Supply pin VOUT 16 14 O DC/DC output PowerPADTM Must be soldered to achieve appropriate power dissipation. Should be connected to PGND. Copyright (c) 2002-2008, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TPS61130 TPS61131 TPS61132 5 TPS61130 TPS61131 TPS61132 www.ti.com SLVS431B - JUNE 2002 - REVISED JANUARY 2008 Functional Block Diagram SWN SWP Backgate Control AntiRinging VBAT VOUT 100 k VOUT Vmax Control 20 pF Gate Control PGND PGND Regulator PGND Error Amplifier _ FB + Vref = 0.5 V Control Logic + _ GND Oscillator Temperature Control EN PGOOD ENLDO SKIPEN LDOIN Backgate Control GND LDOOUT Error Amplifier LBO Low Battery Comparator _ LBI LDOSENSE + Vref = 0.5 V + + _ _ + _ GND Vref = 0.5 V GND 6 Submit Documentation Feedback Copyright (c) 2002-2008, Texas Instruments Incorporated Product Folder Link(s): TPS61130 TPS61131 TPS61132 TPS61130 TPS61131 TPS61132 www.ti.com SLVS431B - JUNE 2002 - REVISED JANUARY 2008 PARAMETER MEASUREMENT INFORMATION C7 10 F U1 L1-A L1-B 22 H Power Supply C3 10 F SWN SWP VBAT VOUT 22 H R3 R1 C6 2.2 F FB VCC1 SEPIC Output C4 100 F LBI R2 LDOIN SKIPEN R6 VCC2 LDO Output LDOOUT R5 C5 2.2 F LDOSENSE EN R7 R4 List of Components: U1 = TPS6113xPW L1 = Coiltronics DRQ74-220 C3, C5, C6, C7 = X7R/X5R Ceramic C4 = Low ESR Tantalum LDOEN R9 LBO Control Outputs PGOOD PGND GND TPS6113xPW TYPICAL CHARACTERISTICS Table of Graphs SEPIC Converter Maximum output current Efficiency Figure vs Input voltage (TPS61130) (VO = 3.3 V, 5.0V, 2.5V) 1, 2 vs Output current (TPS61130) (VO = 2.5 V, VI = 1.8 V) 3 vs Output current (TPS61132) (VO = 3.3 V, VI = 1.8 V, 3.8 V) 4 vs Output current (TPS61130) (VO = 5.0 V, VI = 3.6 V, 6.0 V) 5 vs Input voltage (TPS61132) 6 Output voltage vs Output current (TPS61132) 7 No-load supply current into VBAT vs Input voltage (TPS61132) 8 No-load supply current into VOUT vs Input voltage (TPS61132) 9 Output voltage in continuous mode (TPS61132) 10 Output voltage in power save mode (TPS61132) 11 Load transient response (TPS61132) 12 Line transient response (TPS61132) 13 Start-up after enable (TPS61132) 14 vs Input voltage (VO = 2.5 V, 3.3 V) 15 vs Input voltage (VO = 1.5 V, 1.8 V) 16 Output voltage vs Output current (TPS61131) 17 Dropout voltage vs Output current (TPS61131, TPS61132) 18 Supply current into LDOIN vs LDOIN input voltage (TPS61132) 19 PSRR vs Frequency (TPS61132) 20 Load transient response 21 Line transient response 22 Start-up after enable 23 Waveforms LDO Maximum output current Waveforms Copyright (c) 2002-2008, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TPS61130 TPS61131 TPS61132 7 TPS61130 TPS61131 TPS61132 www.ti.com SLVS431B - JUNE 2002 - REVISED JANUARY 2008 TPS61130 MAXIMUM SEPIC CONVERTER OUTPUT CURRENT vs INPUT VOLTAGE 0.7 TPS61130 MAXIMUM SEPIC CONVERTER OUTPUT CURRENT vs INPUT VOLTAGE 0.70 0.65 0.60 Maximum Output Current - A Maximum Output CURRENT - A 0.6 VO = 3.3 V 0.5 VO = 5 V 0.4 0.3 0.2 VO = 2.5 V 0.55 0.50 0.45 0.40 0.35 0.30 0.25 0.20 0.15 0.10 0.1 0 1.8 2 3 4 5 VI - Input Voltage - V 0.05 0 6 7 1.8 2.2 2.6 3 Figure 1. TPS61130 SEPIC CONVERTER EFFICIENCY vs OUTPUT CURRENT TPS61132 SEPIC CONVERTER EFFICIENCY vs OUTPUT CURRENT 100 100 90 3.4 3.8 4.2 4.6 5 5.4 5.8 6.2 6.6 7 VI - Input Voltage - V Figure 2. TPS61132 VO = 2.5 V VI = 1.8 V VBAT = 3.8 V 90 80 80 70 70 Efficiency - % Efficiency - % VBAT = 1.8 V 60 50 40 60 50 40 30 30 20 20 10 10 0 0.10 0 1 10 100 IO - Output Current - mA 1000 0.1 1 10 100 IO - Output Current - mA Figure 3. 8 Submit Documentation Feedback 1000 Figure 4. Copyright (c) 2002-2008, Texas Instruments Incorporated Product Folder Link(s): TPS61130 TPS61131 TPS61132 TPS61130 TPS61131 TPS61132 www.ti.com SLVS431B - JUNE 2002 - REVISED JANUARY 2008 TPS61130 SEPIC CONVERTER EFFICIENCY vs OUTPUT CURRENT TPS61132 SEPIC CONVERTER EFFICIENCY vs INPUT VOLTAGE 100 100 TPS61130 90 80 VBAT = 6 V 95 VBAT = 3.6 V IO = 100 mA 90 IO = 200 mA Efficiency - % Efficiency - % 70 60 50 40 85 IO = 10 mA 80 75 30 70 20 65 10 60 0 0.1 1 10 100 IO - Output Current - mA 7 Figure 5. Figure 6. TPS61132 SEPIC CONVERTER OUTPUT VOLTAGE vs OUTPUT CURRENT TPS61132 NO-LOAD SUPPLY CURRENT INTO VBAT vs INPUT VOLTAGE 3.40 14 No-Load Supply Current Into VBAT - A VI = 2.4 V 3.38 3.36 VO - Output Voltage - V 3 5 VI - Input Voltage - V 1.8 1000 3.34 3.32 3.30 3.28 3.26 3.24 3.22 3.20 0 100 200 300 IO - Output Current - mA 400 85C 12 25C 10 -40C 8 6 4 2 0 1.8 2 2.2 2.4 2.6 2.8 VI - Input Voltage - V Figure 7. Copyright (c) 2002-2008, Texas Instruments Incorporated 3 3.2 Figure 8. Submit Documentation Feedback Product Folder Link(s): TPS61130 TPS61131 TPS61132 9 TPS61130 TPS61131 TPS61132 www.ti.com SLVS431B - JUNE 2002 - REVISED JANUARY 2008 TPS61132 NO-LOAD SUPPLY CURRENT INTO VOUT vs INPUT VOLTAGE TPS61132 SEPIC CONVERTER OUTPUT VOLTAGE IN CONTINUOUS MODE No-Load Supply Current Into VOUT - A 14 VI = 3.3 V, RL = 33 W 85C 12 Output Voltage 20 mV/Div, AC 25C -40C 10 8 6 Inductor Current 100 mA/Div, DC 4 2 VO = 3.3 V 0 1.8 2 2.2 2.4 2.6 2.8 VI - Input Voltage - V 3 Timebase - 1 s/Div 3.2 Figure 9. Figure 10. TPS61132 SEPIC CONVERTER OUTPUT VOLTAGE IN POWER SAVE MODE TPS61132 SEPIC CONVERTER LOAD TRANSIENT RESPONSE VI = 3.3 V IL = 60 mA to 140 mA VI = 3.3 V, RL = 330 W Current 100 mA/Div, DC Output Voltage 50 mV/Div, AC Output Voltage 20 mV/Div, AC Inductor Current 100 mA/Div, DC VO = 3.3 V VO = 3.3 V Timebase - 200 s/Div Timebase - 500 s/Div Figure 11. 10 Submit Documentation Feedback Figure 12. Copyright (c) 2002-2008, Texas Instruments Incorporated Product Folder Link(s): TPS61130 TPS61131 TPS61132 TPS61130 TPS61131 TPS61132 www.ti.com SLVS431B - JUNE 2002 - REVISED JANUARY 2008 TPS61132 SEPIC CONVERTER LINE TRANSIENT RESPONSE VI = 3.0 V to 4.2 V RL = 33 W TPS61132 SEPIC CONVERTER START-UP AFTER ENABLE Enable 5 V/Div, DC Input Voltage 1 V/Div, DC Output Voltage 2 V/Div, DC Voltage at SW 5 V/Div, DC Output Voltage 50 mV/Div, AC Input Current 200 mA/Div, DC VI = 3.6 V, RL = 66 W VO = 3.3 V VO = 3.3 V Timebase - 400 s/Div Timebase - 200 s/Div Figure 13. Figure 14. MAXIMUM LDO OUTPUT CURRENT vs LDO INPUT VOLTAGE TPS61130 MAXIMUM LDO OUTPUT CURRENT vs LDO INPUT VOLTAGE 400 400 VO = 1.5 V 350 350 Maximum LDO Output Current - mA Maximum LDO Output Current - mA VO = 3.3 V 300 250 VO = 2.5 V 200 150 100 50 300 250 VO = 1.8 V 200 150 100 50 0 0 2.5 3 3.5 4 4.5 5 5.5 LDO Input Voltage - V 6 6.5 7 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 LDO Input Voltage - V Figure 15. Copyright (c) 2002-2008, Texas Instruments Incorporated 6.5 7 Figure 16. Submit Documentation Feedback Product Folder Link(s): TPS61130 TPS61131 TPS61132 11 TPS61130 TPS61131 TPS61132 www.ti.com SLVS431B - JUNE 2002 - REVISED JANUARY 2008 TPS61131 LDO OUTPUT VOLTAGE vs LDO OUTPUT CURRENT LDO DROPOUT VOLTAGE vs LDO OUTPUT CURRENT 3.5 3.4 3.38 3 LDO Dropout Voltage - V LDO Output Voltage - V 3.36 3.34 3.32 3.3 3.28 3.26 TPS61131 (LDO OUTPUT VOLTAGE 1.5 V) 2.5 2 TPS61132 (LDO OUTPUT VOLTAGE 3.3 V) 1.5 1 3.24 0.5 3.22 0 3.2 0 50 100 150 200 250 300 LDO Output Current - mA Figure 17. 350 10 400 60 110 160 210 260 LDO Output Current - mA 310 Figure 18. TPS61132 PSRR vs FREQUENCY TPS61132 SUPPLY CURRENT INTO LDOIN vs LDOIN INPUT VOLTAGE 20 LDOIN = 3.3 V 70 25C 60 LDO Output Current 10 mA 15 PSRR - dB Supply Current Into LDOIN - A 80 85C -40C 10 50 40 30 LDO Output Current 200 mA 20 5 10 0 1.8 12 2 2.2 2.4 2.6 2.8 LDOIN Input Voltage - V Figure 19. Submit Documentation Feedback 3 3.2 0 1k 10k 100k f - Frequency - Hz 1M 10M Figure 20. Copyright (c) 2002-2008, Texas Instruments Incorporated Product Folder Link(s): TPS61130 TPS61131 TPS61132 TPS61130 TPS61131 TPS61132 www.ti.com SLVS431B - JUNE 2002 - REVISED JANUARY 2008 TPS61132 LDO LOAD TRANSIENT RESPONSE VI = 3.3 V IL = 20 mA to 180 mA Output Current 100 mA/Div, DC TPS61132 LDO LINE TRANSIENT RESPONSE VI = 1.8 V to 2.6 V RL = 15 W Input Voltage 1 V/Div, DC Output Voltage 10 mV/Div, AC Output Voltage 20 mV/Div, AC VO = 1.5 V VO = 1.5 V Timebase - 500 s/Div Timebase - 2 ms/Div Figure 21. Figure 22. TPS61132 LDO START-UP AFTER ENABLE VI = 3.3 V RL = 15 W LDO-Enable 5 V/Div, DC LDO-Output Voltage 1 V/Div, DC Input Current 200 mA/Div, DC VO = 1.5 V Timebase - 20 s/Div Figure 23. Copyright (c) 2002-2008, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TPS61130 TPS61131 TPS61132 13 TPS61130 TPS61131 TPS61132 www.ti.com SLVS431B - JUNE 2002 - REVISED JANUARY 2008 DETAILED DESCRIPTION Controller Circuit The controller circuit of the device is based on a fixed frequency multiple feedforward controller topology. Input voltage, output voltage, and voltage drop on the NMOS switch are monitored and forwarded to the regulator. So changes in the operating conditions of the converter directly affect the duty cycle and must not take the indirect and slow way through the control loop and the error amplifier. The control loop, determined by the error amplifier, only has to handle small signal errors. The input for it is the feedback voltage on the FB pin or, at fixed output voltage versions, the voltage on the internal resistor divider. It is compared with the internal reference voltage to generate an accurate and stable output voltage. The peak current of the NMOS switch is also sensed to limit the maximum current flowing through the switch and the inductor. The typical peak current limit is set to 1300 mA. An internal temperature sensor prevents the device from getting overheated in case of excessive power dissipation. Synchronous Rectifier The device integrates an N-channel and a P-channel MOSFET transistor to realize a synchronous rectifier. Because the commonly used discrete Schottky rectifier is replaced with a low RDS(ON) PMOS switch, the power conversion efficiency reaches 90%. To avoid ground shift due to the high currents in the NMOS switch, two separate ground pins are used. The reference for all control functions is the GND pin. The source of the NMOS switch is connected to PGND. Both grounds must be connected on the PCB at only one point close to the GND pin. Due to the nature of the SEPIC topology, there is no dc path from the battery to the output. No additional components must be added in a SEPIC or Flyback topology to make sure the battery is disconnected from the output of the converter. Nevertheless, the backgate diode of the high-side PMOS which is forward biased in standard operation, is turned off in shutdown. This is done by a special circuit which takes the cathode of the backgate diode of the high-side PMOS and disconnects it from the source when the regulator is not enabled (EN = low). Device Enable The device is put into operation when EN is set high. It is put into a shutdown mode when EN is set to GND. In shutdown mode, the regulator stops switching, all internal control circuitry including the low-battery comparator is switched off, and the backgate diode of the rectifying switch is turned off (as described in the Synchronous Rectifier Section). This also means that the output voltage can drop below the input voltage during shutdown. During start-up of the converter, the duty cycle and the peak current are limited in order to avoid high peak currents drawn from the battery. Undervoltage Lockout An undervoltage lockout function prevents device start-up if the supply voltage on VBAT is lower than approximately 1.6 V. When in operation and the battery is being discharged, the device automatically enters the shutdown mode if the voltage on VBAT drops below approximately 1.6 V. This undervoltage lockout function is implemented in order to prevent the malfunctioning of the converter. Softstart When the SEPIC section is enabled, the internal startup cycle starts with switching at a duty cycle of 50%. After the output voltage has reached approximately 1.4V the device continues switching with a variable duty cycle. Until the programmed output voltage is reached, the main switch current limit is set to 40% of its nominal value to avoid high peak inrush currents at the battery during startup. Also the maximum output power during output short circuit conditions is reduced. When the programmed output voltage is reached, the regulator takes control and the switch current limit is set back to 100%. Power Good The PGOOD pin stays high impedance when the dc/dc converter delivers an output voltage within a defined voltage window. So it can be used to enable any connected circuitry such as cascaded converters (LDO) or microprocessor circuits. 14 Submit Documentation Feedback Copyright (c) 2002-2008, Texas Instruments Incorporated Product Folder Link(s): TPS61130 TPS61131 TPS61132 TPS61130 TPS61131 TPS61132 www.ti.com SLVS431B - JUNE 2002 - REVISED JANUARY 2008 Power Save Mode The SKIPEN pin can be used to select different operation modes. To enable the power save mode, SKIPEN must be set high. Power save mode is used to improve efficiency at light loads. In power save mode, the converter only operates when the output voltage trips below a set threshold voltage. It ramps up the output voltage with several pulses, and goes again into power save mode once the output voltage exceeds the set threshold voltage. The power save mode can be disabled by setting the SKIPEN to GND. Low Battery Detector Circuit--LBI/LBO The low-battery detector circuit is typically used to supervise the battery voltage and to generate an error flag when the battery voltage drops below a user-set threshold voltage. The function is active only when the device is enabled. When the device is disabled, the LBO pin is high-impedance. The switching threshold is 500 mV at LBI. During normal operation, LBO stays at high impedance when the voltage, applied at LBI, is above the threshold. It is active low when the voltage at LBI goes below 500 mV. The battery voltage, at which the detection circuit switches, can be programmed with a resistive divider connected to the LBI pin. The resistive divider scales down the battery voltage to a voltage level of 500 mV, which is then compared to the LBI threshold voltage. The LBI pin has a built-in hysteresis of 10 mV. See the application section for more details about the programming of the LBI threshold. If the low-battery detection circuit is not used, the LBI pin should be connected to GND (or to VBAT) and the LBO pin can be left unconnected. Do not let the LBI pin float. Low-EMI Switch The device integrates a circuit that removes the ringing that typically appears on the SW node when the converter enters discontinuous current mode. In this case, the current through the inductor ramps to zero and the rectifying PMOS switch is turned off to prevent a reverse current flowing from the output capacitors back to the battery. Due to the remaining energy that is stored in parasitic components of the semiconductor and the inductor, a ringing on the SW pin is induced. The integrated antiringing switch clamps this voltage to VBAT and therefore dampens ringing. LDO The built-in LDO can be used to generate a second output voltage derived from the dc/dc converter output, from the battery, or from another power source like an ac adapter or a USB power rail. The LDO is capable of being back biased. This allows the user just to connect the outputs of dc/dc converter and LDO. So the device is able to supply the load via dc/dc converter when the energy comes from the battery and efficiency is most important and from another external power source via the LDO when lower efficiency is not critical. The LDO must be disabled if the LDOIN voltage drops below LDOOUT to block reverse current flowing. The status of the dc/dc stage (enabled or disabled) does not matter. LDO Enable The LDO can be separately enabled and disabled by using the LDOEN pin in the same way as the EN pin at the dc/dc converter stage described above. This is completely independent of the status of the EN pin. The voltage levels of the logic signals which need to be applied at LDOEN are related to LDOIN. Copyright (c) 2002-2008, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TPS61130 TPS61131 TPS61132 15 TPS61130 TPS61131 TPS61132 www.ti.com SLVS431B - JUNE 2002 - REVISED JANUARY 2008 APPLICATION INFORMATION DESIGN PROCEDURE The TPS6113x dc/dc converters are intended for systems powered by a dual up to 4 cell NiCd or NiMH battery with a typical terminal voltage between 1.8 V and 6.5 V. They can also be used in systems powered by one-cell Li-Ion with a typical stack voltage between 2.5 V and 4.2 V. Additionally, two up to four primary alkaline battery cells can be the power source in systems where the TPS6113x is used. Programming the Output Voltage DC/DC Converter The output voltage of the TPS61130 dc/dc converter section can be adjusted with an external resistor divider. The typical value of the voltage on the FB pin is 500 mV. The maximum recommended value for the output voltage is 5.5 V. The current through the resistive divider should be about 100 times greater than the current into the FB pin. The typical current into the FB pin is 0.01 A and the voltage across R6 is typically 500 mV. Based on those two values, the recommended value for R6 should be lower than 500 k, in order to set the divider current at 1 A or higher. Because of internal compensation circuitry the value for this resistor should be in the range of 200 k. From that, the value of resistor R3, depending on the needed output voltage (VO), can be calculated using Equation 1: R3 + R6 V O *1 V FB + 180 kW V O *1 500 mV (1) If as an example, an output voltage of 3.3 V is needed, a 1-M resistor should be chosen for R3. If for any reason the value for R6 is chosen significantly lower than 200 k additional capacitance in parallel to R3 is recommended. The required capacitance value can be easily calculated using Equation 2. C parR3 + 20 pF 200R6kW * 1 (2) C7 U1 L1-A 22 H Power Supply C3 10 F 10 F L1-B SWN SWP VBAT VOUT 22 H R3 R1 VCC1 SEPIC Output C4 100 F C6 2.2 F FB LBI R2 LDOIN SKIPEN R6 LDOOUT LDOSENSE EN R4 LDOEN GND VCC2 LDO Output C5 2.2 F R5 R7 R9 LBO Control Outputs PGOOD PGND TPS6113xPW Figure 24. Typical Application Circuit for Adjustable Output Voltage Option 16 Submit Documentation Feedback Copyright (c) 2002-2008, Texas Instruments Incorporated Product Folder Link(s): TPS61130 TPS61131 TPS61132 TPS61130 TPS61131 TPS61132 www.ti.com SLVS431B - JUNE 2002 - REVISED JANUARY 2008 LDO Programming the output voltage of the LDO follows almost the same rules as at the dc/dc converter section. The maximum recommended output voltage of the LDO is 5.5 V. Since reference and internal feedback circuitry are similar, as they are at the dc/dc converter section, R4 also should be in the 200-k range. The calculation of the value of R5 can be done using the following Equation 3: R5 + R4 V O -1 V FB V O -1 500 mV + 180 kW (3) If as an example, an output voltage of 1.5 V is needed, a 360 k-resistor should be chosen for R5. Programming the LBI/LBO Threshold Voltage The current through the resistive divider should be about 100 times greater than the current into the LBI pin. The typical current into the LBI pin is 0.01 A, and the voltage across R2 is equal to the LBI voltage threshold that is generated on-chip, which has a value of 500 mV. The recommended value for R2 is therefore in the range of 500 k. From that, the value of resistor R1, depending on the desired minimum battery voltage VBAT, can be calculated using Equation 4. R1 + R2 V V BAT LBI*threshold *1 V BAT * 1 500 mV + 390 kW (4) The output of the low battery supervisor is a simple open-drain output that goes active low if the dedicated battery voltage drops below the programmed threshold voltage on LBI. The output requires a pullup resistor with a recommended value of 1 M. The maximum voltage which is used to pull up the LBO outputs should not exceed the output voltage of the dc/dc converter. If not used, the LBO pin can be left floating or tied to GND. Inductor Selection A SEPIC converter normally requires three main passive components for storing energy during the conversion. Two inductors, a flying capacitor, and a storage capacitor at the output are required. To select the two inductors, it is recommended to keep the possible peak inductor current below the current limit threshold of the power switch in the chosen configuration. For example, the typical current limit threshold of the TPS6113x's switch is 1300 mA at an output voltage of 3.3 V. The highest peak current through the switch is the sum of the two inductor currents and depends on the output load, the input (VBAT), and the output voltage (VOUT). Estimation of the maximum average inductor current of each inductor can be done using Equation 5: V OUT I +I +I L1*A L1*B OUT V 0.8 BAT (5) For example, for an output current of 300 mA at 3.3 V, at least 680 mA of average current flows through each of the the inductors at a minimum input voltage of 1.8 V. The second parameter for choosing the inductor is the desired current ripple in the inductor. Normally, it is advisable to work with a ripple of around 20% of the average inductor current. A smaller ripple reduces the magnetic hysteresis losses in the inductor, as well as output voltage ripple and EMI. But in the same way, regulation time at load changes rises. In addition, a larger inductor increases the total system costs. With those parameters, it is possible to calculate the value for the inductor by using Equation 6: V V BAT OUT L1 * A + L1 * B + DI V )V L OUT BAT (6) Parameter f is the switching frequency and IL is the ripple current in the inductor, i.e., 40% IL. In this example, the desired inductance is in the range of 20 H. With this calculated value and the calculated currents, it is possible to choose a suitable inductor. In typical applications a 22 H inductance is recommended. The device Copyright (c) 2002-2008, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TPS61130 TPS61131 TPS61132 17 TPS61130 TPS61131 TPS61132 www.ti.com SLVS431B - JUNE 2002 - REVISED JANUARY 2008 has been optimized to operate with inductance values between 10 H and 47 H. Nevertheless operation with higher inductance values may be possible in some applications. Detailed stability analysis is recommended. Care has to be taken that load transients and losses in the circuit can lead to higher currents as estimated in Equation 6. Also, the losses in the inductor caused by magnetic hysteresis losses and copper losses are a major parameter for total circuit efficiency. The following inductor series from different suppliers have been used with the TPS6113X converters: List of Inductors VENDOR Coilcraft RECOMMENDED INDUCTOR SERIES COUPLED INDUCTOR SERIES LPS4012 LPD4012 LPS3015 Cooper Electronics Technologies DR73 DRQ73 DR74 DRQ74 EPCOS B82462G Sumida CDRH5D18 Wurth Electronik 7447789___ 744878220 7447779___ 744877220 Capacitor Selection Input Capacitor At least a 10-F input capacitor is recommended to improve transient behavior of the regulator and EMI behavior of the total power supply circuit. A ceramic capacitor or a tantalum capacitor with a 100-nF ceramic capacitor in parallel, placed close to the IC, is recommended. Flying Capacitor DC/DC Converter In the normal operating mode, the flying capacitor (C7) must be large enough so that the voltage across the capacitor is small. This means the resonance frequency formed by the flying capacitor and the inductors must be at least ten times lower than the switching frequency (see Equation 7). C + 100 min 4p 2 2 L (7) Where L is the inductance of L1-A or L1-B. To optimize efficiency, capacitors with very low ESR such as ceramic capacitors are recommended. The voltage rating of the flying capacitor must be higher than the input voltage VBAT. Output Capacitor DC/DC Converter The major parameter necessary to define the output capacitor is the maximum allowed output voltage ripple of the converter. This ripple is determined by two parameters of the capacitor, the capacitance and the ESR. It is possible to calculate the minimum capacitance needed for the defined ripple, supposing that the ESR is zero, by using Equation 8: I V OUT OUT C + min DV V )V OUT BAT (8) Parameter f is the switching frequency and V is the maximum allowed ripple. With a chosen ripple voltage of 15 mV, a minimum capacitance of 26 F is needed. The total ripple is larger due to the ESR of the output capacitor. This additional component of the ripple can be calculated using Equation 9: DV +I R ESR OUT ESR (9) An additional ripple of 24 mV is the result of using a tantalum capacitor with a low ESR of 80 m. The total ripple is the sum of the ripple caused by the capacitance and the ripple caused by the ESR of the capacitor. In this example, the total ripple is 39 mV. Additional ripple is caused by load transients. This means that the output 18 Submit Documentation Feedback Copyright (c) 2002-2008, Texas Instruments Incorporated Product Folder Link(s): TPS61130 TPS61131 TPS61132 TPS61130 TPS61131 TPS61132 www.ti.com SLVS431B - JUNE 2002 - REVISED JANUARY 2008 capacitance needs to be larger than calculated above to meet the total ripple requirements. The output capacitor has to completely supply the load during the charging phase of the inductor. A reasonable value of the output capacitance depends on the speed of the load transients and the load current during the load change. With the calculated minimum value of 26 Fand load transient considerations the recommended output capacitance value is in a 100 F range. For economical reasons this usually is a tantalum capacitor. Because of this the control loop has been optimized for using output capacitors with an ESR of above 30 m. The minimum value for the output capacitor is 22 F. Small Signal Stability When using output capacitors with lower ESR, like ceramics, it is recommended to use the adjustable voltage version. The missing ESR can be easily compensated there in the feedback divider. Typically a capacitor in the range of 10 pF in parallel with R3 helps to obtain small signal stability, with the lowest ESR output capacitors. For more detailed analysis the small signal transfer function of the error amplifier and regulator, which is given in Equation 10, can be used. 10 (R3 ) R6) A + d + REG V R6 (1 ) i w 1.6 ms) FB (10) Output Capacitor LDO To ensure stable output regulation, it is required to use an output capacitor at the LDO output. Ceramic capacitors in the range from 1 F up to 4.7 F are recommend. At 4.7 F and above it is recommended to use standard ESR tantalum. There is no maximum capacitance value. Layout Considerations For all switching power supplies, the layout is an important step in the design, especially at high peak currents and high switching frequencies. If the layout is not carefully done, the regulator could show stability problems as well as EMI problems. Therefore, use wide and short traces for the main current path and for the power ground tracks. The input capacitor, output capacitor, and the inductor should be placed as close as possible to the IC. Use a common ground node for power ground and a different one for control ground to minimize the effects of ground noise. Connect these ground nodes at any place close to one of the ground pins of the IC. The feedback divider should be placed as close as possible to the control ground pin of the IC. To lay out the control ground, it is recommended to use short traces as well, separated from the power ground traces. This avoids ground shift problems, which can occur due to superimposition of power ground current and control ground current. Copyright (c) 2002-2008, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TPS61130 TPS61131 TPS61132 19 TPS61130 TPS61131 TPS61132 www.ti.com SLVS431B - JUNE 2002 - REVISED JANUARY 2008 APPLICATION EXAMPLES C7 10 F U1 L1-A L1-B 22 H SWN SWP VBAT VOUT 22 H C6 2.2 F R1 C3 10 F LBI R2 3.3 V, >250 mA C4 100 F LDOIN SKIPEN LDOOUT C5 2.2 F LDOSENSE EN R7 LDOEN List of Components: U1 = TPS61132PW L1 = Coiltronics DRQ74-220 C3, C5, C6, C7 = X7R/X5R Ceramic C4 = Low ESR Tantalum R9 LBO LBO PGOOD PGND GND 1.5 V, >120 mA PGOOD TPS61132PW Figure 25. Solution for Maximum Output Power C7 10 F U1 L1 L2 22 H SWN SWP VBAT VOUT 22 H 3.3 V C6 2.2 F R1 C3 10 F LBI R2 LDOIN SKIPEN 1.5 V LDOOUT C5 2.2 F LDOSENSE EN R7 List of Components: U1 = TPS61132PW L1 , L2 = Sumida 5D18-220 C3, C5, C6, C7 = X7R/X5R Ceramic C4 = Low ESR, Low Profile Tantalum C4 100 F LDOEN GND LBO R9 LBO PGOOD PGND PGOOD TPS61132PW Figure 26. Low Profile Solution, Maximum Height 1,8 mm 20 Submit Documentation Feedback Copyright (c) 2002-2008, Texas Instruments Incorporated Product Folder Link(s): TPS61130 TPS61131 TPS61132 TPS61130 TPS61131 TPS61132 www.ti.com SLVS431B - JUNE 2002 - REVISED JANUARY 2008 C7 10 F U1 L1-A L1-B 22 H SWN SWP VBAT VOUT R3 R1 C3 10 F 22 H C6 22 F FB LBI R6 R2 LDOIN LDOOUT SKIPEN 3.3 V R5 LDOSENSE EN R7 R4 LDOEN List of Components: U1 = TPS61130PW L1 = Coiltronics DRQ74-220 C3, C5, C7 = X7R/X5R Ceramic C6 = X7R/X5R Ceramic or Low ESR Tantalum R9 C5 2.2 F LBO LBO PGOOD PGOOD PGND GND TPS61130PW Figure 27. Single Output Using LDO as Filter USB Input 4.2 V...5.5 V D1 C7 10 F U1 L1-B L1-A SWN 22 H VBAT C3 10 F SWP 22 H VOUT R3 1 M R1 FB LBI R2 LDOIN SYNC EN List of Components: U1 = TPS61130PW L1 = Coiltronics DRQ74-220 C3, C5, C6, C7 = X7R/X5R Ceramic C4 = Low ESR Tantalum D1 = On-Semiconductor MBR0520 LDOOUT LDOSENSE R5 1.022 M R7 LBO GND C4 100 F R6 180 k R4 180 k LDOEN C6 2.2 F VCC 3.3 V System Supply R8 Control Outputs PGOOD PGND TPS61130PW Figure 28. Dual Input Power Supply Solution Copyright (c) 2002-2008, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TPS61130 TPS61131 TPS61132 21 TPS61130 TPS61131 TPS61132 www.ti.com SLVS431B - JUNE 2002 - REVISED JANUARY 2008 THERMAL INFORMATION Implementation of integrated circuits in low-profile and fine-pitch surface-mount packages typically requires special attention to power dissipation. Many system-dependent issues such as thermal coupling, airflow, added heat sinks and convection surfaces, and the presence of other heat-generating components affect the power-dissipation limits of a given component. Three basic approaches for enhancing thermal performance are listed below. * Improving the power dissipation capability of the PCB design. * Improving the thermal coupling of the component to the PCB. * Introducing airflow in the system. The maximum recommended junction temperature (TJ) of the TPS6113x devices is 150C. The thermal resistance of the 16-pin TSSOP package (PW) is RJA = 155 C/W. The 16-pin QFN PowerPAD package (RSA) has a thermal resistance of RJA = 38.1 C/W, if the PowerPAD is soldered and the board layout is optimized. Specified regulator operation is assured to a maximum ambient temperature TA of 85C. Therefore, the maximum power dissipation is about 420 mW for the TSSOP (PW) package and 1700 mW for the QFN (RSA) package. More power can be dissipated if the maximum ambient temperature of the application is lower (see Equation 11). T *T J(MAX) A P + + 150C * 85C + 420 mW D(MAX) R 155CW qJA (11) If designing for a lower junction temperature of 125C, which is recommended, maximum heat dissipation is lower. Using the above Equation 11 results in 1050 mW power dissipation for the RSA package and 260 mW for the PW package. 22 Submit Documentation Feedback Copyright (c) 2002-2008, Texas Instruments Incorporated Product Folder Link(s): TPS61130 TPS61131 TPS61132 PACKAGE MATERIALS INFORMATION www.ti.com 17-Aug-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device TPS61130PWR Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant TSSOP PW 16 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 TPS61130RSAR QFN RSA 16 3000 330.0 12.4 4.3 4.3 1.5 8.0 12.0 Q2 TPS61131PWR TSSOP PW 16 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 TPS61132RSAR QFN RSA 16 3000 330.0 12.4 4.3 4.3 1.5 8.0 12.0 Q2 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 17-Aug-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TPS61130PWR TSSOP PW 16 2000 367.0 367.0 35.0 TPS61130RSAR QFN RSA 16 3000 338.1 338.1 20.6 TPS61131PWR TSSOP PW 16 2000 367.0 367.0 35.0 TPS61132RSAR QFN RSA 16 3000 338.1 338.1 20.6 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated