LM1575,LM2575,LM2575HV LM1575/LM2575/LM2575HV SIMPLE SWITCHER 1A Step-Down Voltage Regulator Literature Number: SNVS106D LM1575/LM2575/LM2575HV SIMPLE SWITCHER(R) 1A Step-Down Voltage Regulator General Description Features The LM2575 series of regulators are monolithic integrated circuits that provide all the active functions for a step-down (buck) switching regulator, capable of driving a 1A load with excellent line and load regulation. These devices are available in fixed output voltages of 3.3V, 5V, 12V, 15V, and an adjustable output version. Requiring a minimum number of external components, these regulators are simple to use and include internal frequency compensation and a fixed-frequency oscillator. The LM2575 series offers a high-efficiency replacement for popular three-terminal linear regulators. It substantially reduces the size of the heat sink, and in many cases no heat sink is required. A standard series of inductors optimized for use with the LM2575 are available from several different manufacturers. This feature greatly simplifies the design of switch-mode power supplies. Other features include a guaranteed 4% tolerance on output voltage within specified input voltages and output load conditions, and 10% on the oscillator frequency. External shutdown is included, featuring 50 A (typical) standby current. The output switch includes cycle-by-cycle current limiting, as well as thermal shutdown for full protection under fault conditions. 3.3V, 5V, 12V, 15V, and adjustable output versions Adjustable version output voltage range, 1.23V to 37V (57V for HV version) 4% max over line and load conditions Guaranteed 1A output current Wide input voltage range, 40V up to 60V for HV version Requires only 4 external components 52 kHz fixed frequency internal oscillator TTL shutdown capability, low power standby mode High efficiency Uses readily available standard inductors Thermal shutdown and current limit protection P+ Product Enhancement tested Applications Simple high-efficiency step-down (buck) regulator Efficient pre-regulator for linear regulators On-card switching regulators Positive to negative converter (Buck-Boost) Typical Application (Fixed Output Voltage Versions) 1147501 Note: Pin numbers are for the TO-220 package. SIMPLE SWITCHER(R) is a registered trademark of National Semiconductor Corporation (c) 2007 National Semiconductor Corporation 11475 www.national.com LM1575/LM2575/LM2575HV Series SIMPLE SWITCHER 1A Step-Down Voltage Regulator April 2007 LM1575/LM2575/LM2575HV Block Diagram and Typical Application 1147502 3.3V, R2 = 1.7k 5V, R2 = 3.1k 12V, R2 = 8.84k 15V, R2 = 11.3k For ADJ. Version R1 = Open, R2 = 0 Note: Pin numbers are for the TO-220 package. FIGURE 1. www.national.com 2 (XX indicates output voltage option. See Ordering Information table for complete part number.) Straight Leads 5-Lead TO-220 (T) Bent, Staggered Leads 5-Lead TO-220 (T) 1147524 1147522 1147523 Top View LM2575T-XX or LM2575HVT-XX See NS Package Number T05A Top View 16-Lead DIP (N or J) Side View LM2575T-XX Flow LB03 or LM2575HVT-XX Flow LB03 See NS Package Number T05D 24-Lead Surface Mount (M) 1147525 *No Internal Connection Top View LM2575N-XX or LM2575HVN-XX See NS Package Number N16A LM1575J-XX-QML See NS Package Number J16A 1147526 *No Internal Connection Top View LM2575M-XX or LM2575HVM-XX See NS Package Number M24B TO-263(S) 5-Lead Surface-Mount Package 1147529 Top View 1147530 Side View LM2575S-XX or LM2575HVS-XX See NS Package Number TS5B 3 www.national.com LM1575/LM2575/LM2575HV Connection Diagrams LM1575/LM2575/LM2575HV Ordering Information Package Type NSC Package Number Standard Voltage Rating (40V) High Voltage Rating (60V) 5-Lead TO-220 Straight Leads T05A LM2575T-3.3 LM2575T-5.0 LM2575T-12 LM2575T-15 LM2575T-ADJ LM2575HVT-3.3 LM2575HVT-5.0 LM2575HVT-12 LM2575HVT-15 LM2575HVT-ADJ 5-Lead TO-220 Bent and Staggered Leads T05D LM2575T-3.3 Flow LB03 LM2575T-5.0 Flow LB03 LM2575T-12 Flow LB03 LM2575T-15 Flow LB03 LM2575T-ADJ Flow LB03 LM2575HVT-3.3 Flow LB03 LM2575HVT-5.0 Flow LB03 LM2575HVT-12 Flow LB03 LM2575HVT-15 Flow LB03 LM2575HVT-ADJ Flow LB03 16-Pin Molded DIP N16A LM2575N-5.0 LM2575N-12 LM2575N-15 LM2575N-ADJ LM2575HVN-5.0 LM2575HVN-12 LM2575HVN-15 LM2575HVN-ADJ 24-Pin Surface Mount M24B LM2575M-5.0 LM2575M-12 LM2575M-15 LM2575M-ADJ LM2575HVM-5.0 LM2575HVM-12 LM2575HVM-15 LM2575HVM-ADJ 5-Lead TO-263 Surface Mount TS5B LM2575S-3.3 LM2575S-5.0 LM2575S-12 LM2575S-15 LM2575S-ADJ LM2575HVS-3.3 LM2575HVS-5.0 LM2575HVS-12 LM2575HVS-15 LM2575HVS-ADJ 16-Pin Ceramic DIP J16A LM1575J-3.3-QML LM1575J-5.0-QML LM1575J-12-QML -40C TJ +125C -55C TJ +150C LM1575J-15-QML LM1575J-ADJ-QML www.national.com Temperature Range 4 Minimum ESD Rating If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. (C = 100 pF, R = 1.5 k) Lead Temperature (Soldering, 10 sec.) Maximum Supply Voltage LM1575/LM2575 LM2575HV ON /OFF Pin Input Voltage Output Voltage to Ground (Steady State) Power Dissipation Storage Temperature Range Maximum Junction Temperature 2 kV 260C Operating Ratings 45V 63V Temperature Range LM1575 -0.3V V +VIN -55C TJ +150C -40C TJ +125C LM2575/LM2575HV -1V Internally Limited -65C to +150C 150C Supply Voltage LM1575/LM2575 LM2575HV 40V 60V LM1575-3.3, LM2575-3.3, LM2575HV-3.3 Electrical Characteristics Specifications with standard type face are for TJ = 25C, and those with boldface type apply over full Operating Temperature Range . Symbol Parameter Conditions Typ LM1575-3.3 LM2575-3.3 Units LM2575HV-3.3 (Limits) Limit (Note 2) Limit (Note 3) 3.267 3.333 3.234 3.366 V(Min) V(Max) 3.200/3.168 3.400/3.432 3.168/3.135 3.432/3.465 V(Min) V(Max) SYSTEM PARAMETERS (Note 4) Test Circuit Figure 2 VOUT Output Voltage VIN = 12V, ILOAD = 0.2A 3.3 V Circuit of Figure 2 VOUT VOUT Output Voltage 4.75V VIN 40V, 0.2A ILOAD 1A LM1575/LM2575 Circuit of Figure 2 Output Voltage 4.75V VIN 60V, 0.2A ILOAD 1A LM2575HV Circuit of Figure 2 Efficiency VIN = 12V, ILOAD = 1A 3.3 V 3.3 V 3.200/3.168 3.416/3.450 3.168/3.135 3.450/3.482 75 V(Min) V(Max) % LM1575-5.0, LM2575-5.0, LM2575HV-5.0 Electrical Characteristics Specifications with standard type face are for TJ = 25C, and those with boldface type apply over full Operating Temperature Range. Symbol Parameter Conditions Typ LM1575-5.0 LM2575-5.0 LM2575HV-5.0 Limit (Note 2) Limit (Note 3) Units (Limits) SYSTEM PARAMETERS (Note 4) Test Circuit Figure 2 VOUT Output Voltage VIN = 12V, ILOAD = 0.2A 5.0 Circuit of Figure 2 VOUT V 4.950 5.050 4.900 5.100 V(Min) V(Max) Output Voltage 0.2A ILOAD 1A, LM1575/LM2575 8V VIN 40V 4.850/4.800 4.800/4.750 V(Min) Circuit of Figure 2 5.150/5.200 5.200/5.250 V(Max) 5.0 5 V www.national.com LM1575/LM2575/LM2575HV Absolute Maximum Ratings (Note 1) LM1575/LM2575/LM2575HV Symbol VOUT Parameter Conditions Output Voltage 0.2A ILOAD 1A, LM2575HV 8V VIN 60V Typ Efficiency LM2575-5.0 LM2575HV-5.0 Limit (Note 2) Limit (Note 3) 5.0 Circuit of Figure 2 LM1575-5.0 VIN = 12V, ILOAD = 1A Units (Limits) V 4.850/4.800 4.800/4.750 V(Min) 5.175/5.225 5.225/5.275 V(Max) 77 % LM1575-12, LM2575-12, LM2575HV-12 Electrical Characteristics Specifications with standard type face are for TJ = 25C, and those with boldface type apply over full Operating Temperature Range . Symbol Parameter Conditions Typ LM1575-12 LM2575-12 LM2575HV-12 Limit (Note 2) Limit (Note 3) Units (Limits) SYSTEM PARAMETERS (Note 4) Test Circuit Figure 2 VOUT Output Voltage VIN = 25V, ILOAD = 0.2A 12 Circuit of Figure 2 VOUT Output Voltage 0.2A ILOAD 1A, LM1575/LM2575 15V VIN 40V 11.88 12.12 11.76 12.24 12 Circuit of Figure 2 VOUT V V(Min) V(Max) V 11.64/11.52 11.52/11.40 V(Min) 12.36/12.48 12.48/12.60 V(Max) Output Voltage 0.2A ILOAD 1A, LM2575HV 15V VIN 60V 11.64/11.52 11.52/11.40 V(Min) Circuit of Figure 2 12.42/12.54 12.54/12.66 V(Max) Efficiency 12 VIN = 15V, ILOAD = 1A V 88 % LM1575-15, LM2575-15, LM2575HV-15 Electrical Characteristics Specifications with standard type face are for TJ = 25C, and those with boldface type apply over full Operating Temperature Range . Symbol Parameter Conditions Typ LM1575-15 LM2575-15 LM2575HV-15 Limit (Note 2) Limit (Note 3) 14.85 15.15 14.70 15.30 Units (Limits) SYSTEM PARAMETERS (Note 4) Test Circuit Figure 2 VOUT Output Voltage VIN = 30V, ILOAD = 0.2A 15 Circuit of Figure 2 VOUT VOUT Output Voltage 0.2A ILOAD 1A, LM1575/LM2575 18V VIN 40V 14.55/14.40 14.40/14.25 V(Min) Circuit of Figure 2 15.45/15.60 15.60/15.75 V(Max) 14.55/14.40 14.40/14.25 V(Min) 15.525/15.675 15.68/15.83 V(Max) Output Voltage 0.2A ILOAD 1A, LM2575HV 18V VIN 60V 15 Efficiency www.national.com V 15 Circuit of Figure 2 V V(Min) V(Max) VIN = 18V, ILOAD = 1A 88 6 V % Specifications with standard type face are for TJ= 25C, and those with boldface type apply over full Operating Temperature Range. Symbol Parameter Conditions Typ LM1575-ADJ LM2575-ADJ LM2575HV-ADJ Units (Limits) Limit (Note 2) Limit (Note 3) 1.217 1.217 V(Min) 1.243 1.243 V(Max) SYSTEM PARAMETERS (Note 4) Test Circuit Figure 2 VOUT Feedback Voltage VIN = 12V, ILOAD = 0.2A 1.230 V VOUT = 5V Circuit of Figure 2 VOUT VOUT Feedback Voltage 0.2A ILOAD 1A, LM1575/LM2575 8V VIN 40V 1.205/1.193 1.193/1.180 V(Min) VOUT = 5V, Circuit of Figure 2 1.255/1.267 1.267/1.280 V(Max) 1.230 V Feedback Voltage 0.2A ILOAD 1A, LM2575HV 8V VIN 60V 1.205/1.193 1.193/1.180 V(Min) VOUT = 5V, Circuit of Figure 2 1.261/1.273 1.273/1.286 V(Max) Efficiency 1.230 VIN = 12V, ILOAD = 1A, VOUT = 5V V 77 % All Output Voltage Versions Electrical Characteristics Specifications with standard type face are for TJ = 25C, and those with boldface type apply over full Operating Temperature Range. Unless otherwise specified, VIN = 12V for the 3.3V, 5V, and Adjustable version, VIN = 25V for the 12V version, and VIN = 30V for the 15V version. ILOAD = 200 mA. Symbol Parameter Conditions Typ LM1575-XX LM2575-XX LM2575HV-XX Units (Limits) Limit (Note 2) Limit (Note 3) 100/500 100/500 nA 47/43 58/62 47/42 58/63 kHz(Min) kHz(Max) DEVICE PARAMETERS Ib Feedback Bias Current VOUT = 5V (Adjustable Version Only) 50 fO Oscillator Frequency (Note 13) 52 VSAT Saturation Voltage IOUT = 1A (Note 5) 0.9 DC Max Duty Cycle (ON) (Note 6) 98 ICL IL Current Limit Output Leakage Peak Current (Notes 5, 13) (Notes 7, 8) Current ISTBY Quiescent Current Standby Quiescent V 1.2/1.4 1.2/1.4 V(Max) 93 93 % %(Min) 2.2 Output = 0V Output = -1V (Note 7) A 1.7/1.3 3.0/3.2 1.7/1.3 3.0/3.2 A(Min) A(Max) 2 2 mA(Max) 30 30 mA(Max) 10/12 10 mA(Max) 200/500 200 A(Max) 7.5 Output = -1V IQ kHz mA 5 ON /OFF Pin = 5V (OFF) mA A 50 Current 7 www.national.com LM1575/LM2575/LM2575HV LM1575-ADJ, LM2575-ADJ, LM2575HV-ADJ Electrical Characteristics LM1575/LM2575/LM2575HV Symbol JA Parameter Thermal Resistance Conditions Typ T Package, Junction to Ambient (Note 9) 65 JA T Package, Junction to Ambient (Note 10) 45 JC T Package, Junction to Case 2 JA N Package, Junction to Ambient (Note 11) 85 JA M Package, Junction to Ambient (Note 11) 100 JA S Package, Junction to Ambient (Note 12) 37 LM1575-XX LM2575-XX LM2575HV-XX Limit (Note 2) Limit (Note 3) Units (Limits) C/W ON /OFF CONTROL Test Circuit Figure 2 VIH ON /OFF Pin Logic VOUT = 0V 1.4 2.2/2.4 2.2/2.4 V(Min) VIL Input Level VOUT = Nominal Output Voltage 1.2 1.0/0.8 1.0/0.8 V(Max) IIH ON /OFF Pin Input ON /OFF Pin = 5V (OFF) 12 30 30 A(Max) 10 10 A(Max) Current IIL ON /OFF Pin = 0V (ON) A A 0 Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. Note 2: All limits guaranteed at room temperature (standard type face) and at temperature extremes (bold type face). All limits are used to calculate Average Outgoing Quality Level, and all are 100% production tested. Note 3: All limits guaranteed at room temperature (standard type face) and at temperature extremes (bold type face). All room temperature limits are 100% production tested. All limits at temperature extremes are guaranteed via correlation using standard Statistical Quality Control (SQC) methods. Note 4: External components such as the catch diode, inductor, input and output capacitors can affect switching regulator system performance. When the LM1575/ LM2575 is used as shown in the Figure 2 test circuit, system performance will be as shown in system parameters section of Electrical Characteristics. Note 5: Output (pin 2) sourcing current. No diode, inductor or capacitor connected to output pin. Note 6: Feedback (pin 4) removed from output and connected to 0V. Note 7: Feedback (pin 4) removed from output and connected to +12V for the Adjustable, 3.3V, and 5V versions, and +25V for the 12V and 15V versions, to force the output transistor OFF. Note 8: VIN = 40V (60V for the high voltage version). Note 9: Junction to ambient thermal resistance (no external heat sink) for the 5 lead TO-220 package mounted vertically, with 1/2 inch leads in a socket, or on a PC board with minimum copper area. Note 10: Junction to ambient thermal resistance (no external heat sink) for the 5 lead TO-220 package mounted vertically, with 1/2 inch leads soldered to a PC board containing approximately 4 square inches of copper area surrounding the leads. Note 11: Junction to ambient thermal resistance with approximately 1 square inch of pc board copper surrounding the leads. Additional copper area will lower thermal resistance further. See thermal model in Switchers made Simple software. Note 12: If the TO-263 package is used, the thermal resistance can be reduced by increasing the PC board copper area thermally connected to the package: Using 0.5 square inches of copper area, JA is 50C/W; with 1 square inch of copper area, JA is 37C/W; and with 1.6 or more square inches of copper area, JA is 32C/W. Note 13: The oscillator frequency reduces to approximately 18 kHz in the event of an output short or an overload which causes the regulated output voltage to drop approximately 40% from the nominal output voltage. This self protection feature lowers the average power dissipation of the IC by lowering the minimum duty cycle from 5% down to approximately 2%. Note 14: Refer to RETS LM1575J for current revision of military RETS/SMD. www.national.com 8 LM1575/LM2575/LM2575HV Typical Performance Characteristics (Circuit of Figure 2) Normalized Output Voltage Line Regulation 1147533 1147532 Dropout Voltage Current Limit 1147534 1147535 Quiescent Current Standby Quiescent Current 1147536 1147537 9 www.national.com LM1575/LM2575/LM2575HV Oscillator Frequency Switch Saturation Voltage 1147538 1147539 Efficiency Minimum Operating Voltage 1147541 1147540 Quiescent Current vs Duty Cycle Feedback Voltage vs Duty Cycle 1147542 www.national.com 1147543 10 LM1575/LM2575/LM2575HV Feedback Pin Current Maximum Power Dissipation (TO-263) (See (Note 12)) 1147505 1147528 Switching Waveforms Load Transient Response 1147506 VOUT = 5V A: Output Pin Voltage, 10V/div B: Output Pin Current, 1A/div C: Inductor Current, 0.5A/div D: Output Ripple Voltage, 20 mV/div, AC-Coupled Horizontal Time Base: 5 s/div 1147507 11 www.national.com LM1575/LM2575/LM2575HV by heavy lines should be kept as short as possible. Singlepoint grounding (as indicated) or ground plane construction should be used for best results. When using the Adjustable version, physically locate the programming resistors near the regulator, to keep the sensitive feedback wiring short. Test Circuit and Layout Guidelines As in any switching regulator, layout is very important. Rapidly switching currents associated with wiring inductance generate voltage transients which can cause problems. For minimal inductance and ground loops, the length of the leads indicated Fixed Output Voltage Versions 1147508 CIN -- 100 F, 75V, Aluminum Electrolytic COUT -- 330 F, 25V, Aluminum Electrolytic D1 -- Schottky, 11DQ06 L1 -- 330 H, PE-52627 (for 5V in, 3.3V out, use 100 H, PE-92108) Adjustable Output Voltage Version 1147509 where VREF = 1.23V, R1 between 1k and 5k. R1 -- 2k, 0.1% R2 -- 6.12k, 0.1% Note: Pin numbers are for the TO-220 package. FIGURE 2. www.national.com 12 PROCEDURE (Fixed Output Voltage Versions) Given: VOUT = Regulated Output Voltage (3.3V, 5V, 12V, or 15V) VIN(Max) = Maximum Input Voltage ILOAD(Max) = Maximum Load Current 1. Inductor Selection (L1) A. Select the correct Inductor value selection guide from Figures 3, 4, 5, 6 (Output voltages of 3.3V, 5V, 12V or 15V respectively). For other output voltages, see the design procedure for the adjustable version. B. From the inductor value selection guide, identify the inductance region intersected by VIN(Max) and ILOAD(Max), and note the inductor code for that region. C. Identify the inductor value from the inductor code, and select an appropriate inductor from the table shown in Figure 9. Part numbers are listed for three inductor manufacturers. The inductor chosen must be rated for operation at the LM2575 switching frequency (52 kHz) and for a current rating of 1.15 x ILOAD. For additional inductor information, see the inductor section in the Application Hints section of this data sheet. 2. Output Capacitor Selection (COUT) A. The value of the output capacitor together with the inductor defines the dominate pole-pair of the switching regulator loop. For stable operation and an acceptable output ripple voltage, (approximately 1% of the output voltage) a value between 100 F and 470 F is recommended. B. The capacitor's voltage rating should be at least 1.5 times greater than the output voltage. For a 5V regulator, a rating of at least 8V is appropriate, and a 10V or 15V rating is recommended. Higher voltage electrolytic capacitors generally have lower ESR numbers, and for this reason it may be necessary to select a capacitor rated for a higher voltage than would normally be needed. 3. Catch Diode Selection (D1) A. The catch-diode current rating must be at least 1.2 times greater than the maximum load current. Also, if the power supply design must withstand a continuous output short, the diode should have a current rating equal to the maximum current limit of the LM2575. The most stressful condition for this diode is an overload or shorted output condition. B. The reverse voltage rating of the diode should be at least 1.25 times the maximum input voltage. 4. Input Capacitor (CIN) An aluminum or tantalum electrolytic bypass capacitor located close to the regulator is needed for stable operation. EXAMPLE (Fixed Output Voltage Versions) Given: VOUT = 5V VIN(Max) = 20V ILOAD(Max) = 0.8A 1. Inductor Selection (L1) A. Use the selection guide shown in Figure 4. B. From the selection guide, the inductance area intersected by the 20V line and 0.8A line is L330. C. Inductor value required is 330 H. From the table in Figure 9, choose AIE 415-0926, Pulse Engineering PE-52627, or RL1952. 2. Output Capacitor Selection (COUT) A. COUT = 100 F to 470 F standard aluminum electrolytic. B. Capacitor voltage rating = 20V. 3. Catch Diode Selection (D1) A. For this example, a 1A current rating is adequate. B. Use a 30V 1N5818 or SR103 Schottky diode, or any of the suggested fast-recovery diodes shown in Figure 8. 4. Input Capacitor (CIN) A 47 F, 25V aluminum electrolytic capacitor located near the input and ground pins provides sufficient bypassing. 13 www.national.com LM1575/LM2575/LM2575HV LM2575 Series Buck Regulator Design Procedure LM1575/LM2575/LM2575HV Inductor Value Selection Guides (For Continuous Mode Operation) 1147512 1147510 FIGURE 5. LM2575(HV)-12 FIGURE 3. LM2575(HV)-3.3 1147513 1147511 FIGURE 6. LM2575(HV)-15 FIGURE 4. LM2575(HV)-5.0 1147514 FIGURE 7. LM2575(HV)-ADJ www.national.com 14 EXAMPLE (Adjustable Output Voltage Versions) Given: VOUT = 10V VIN(Max) = 25V ILOAD(Max) = 1A F = 52 kHz 1.Programming Output Voltage (Selecting R1 and R2) R1 can be between 1k and 5k. (For best temperature coefficient and stability with time, use 1% metal film resistors) R2 = 1k (8.13 - 1) = 7.13k, closest 1% value is 7.15k 2. Inductor Selection (L1) A. Calculate the inductor Volt * microsecond constant, E * T (V * s), from the following formula: 2. Inductor Selection (L1) A. Calculate E * T (V * s) B. Use the E * T value from the previous formula and match it with the E * T number on the vertical axis of the Inductor Value Selection Guide shown in Figure 7. C. On the horizontal axis, select the maximum load current. D. Identify the inductance region intersected by the E * T value and the maximum load current value, and note the inductor code for that region. E. Identify the inductor value from the inductor code, and select an appropriate inductor from the table shown in Figure 9. Part numbers are listed for three inductor manufacturers. The inductor chosen must be rated for operation at the LM2575 switching frequency (52 kHz) and for a current rating of 1.15 x ILOAD. For additional inductor information, see the inductor section in the application hints section of this data sheet. 3. Output Capacitor Selection (COUT) A. The value of the output capacitor together with the inductor defines the dominate pole-pair of the switching regulator loop. For stable operation, the capacitor must satisfy the following requirement: B. E * T = 115 V * s C. ILOAD(Max) = 1A D. Inductance Region = H470 E. Inductor Value = 470 H Choose from AIE part #430-0634, Pulse Engineering part #PE-53118, or Renco part #RL-1961. 3. Output Capacitor Selection (COUT) A. However, for acceptable output ripple voltage select COUT 220 F COUT = 220 F electrolytic capacitor The above formula yields capacitor values between 10 F and 2000 F that will satisfy the loop requirements for stable operation. But to achieve an acceptable output ripple voltage, (approximately 1% of the output voltage) and transient response, the output capacitor may need to be several times larger than the above formula yields. B. The capacitor's voltage rating should be at last 1.5 times greater than the output voltage. For a 10V regulator, a rating of at least 15V or more is recommended. Higher voltage electrolytic capacitors generally have lower ESR numbers, and for this reason it may be necessary to select a capacitor rate for a higher voltage than would normally be needed. (Continued) (Continued) 15 www.national.com LM1575/LM2575/LM2575HV PROCEDURE (Adjustable Output Voltage Versions) Given: VOUT = Regulated Output Voltage VIN(Max) = Maximum Input Voltage ILOAD(Max) = Maximum Load Current F = Switching Frequency (Fixed at 52 kHz) 1. Programming Output Voltage (Selecting R1 and R2, as shown in Figure 2 ) Use the following formula to select the appropriate resistor values. LM1575/LM2575/LM2575HV PROCEDURE (Adjustable Output Voltage Versions) 4. Catch Diode Selection (D1) A. The catch-diode current rating must be at least 1.2 times greater than the maximum load current. Also, if the power supply design must withstand a continuous output short, the diode should have a current rating equal to the maximum current limit of the LM2575. The most stressful condition for this diode is an overload or shorted output. See diode selection guide in Figure 8. B. The reverse voltage rating of the diode should be at least 1.25 times the maximum input voltage. 5. Input Capacitor (CIN) An aluminum or tantalum electrolytic bypass capacitor located close to the regulator is needed for stable operation. EXAMPLE (Adjustable Output Voltage Versions) 4. Catch Diode Selection (D1) A. For this example, a 3A current rating is adequate. B. Use a 40V MBR340 or 31DQ04 Schottky diode, or any of the suggested fast-recovery diodes in Figure 8. 5. Input Capacitor (CIN) A 100 F aluminum electrolytic capacitor located near the input and ground pins provides sufficient bypassing. To further simplify the buck regulator design procedure, National Semiconductor is making available computer design software to be used with the Simple Switcher line of switching regulators. Switchers Made Simple (version 3.3) is available on a (31/2) diskette for IBM compatible computers from a National Semiconductor sales office in your area. www.national.com 16 Schottky 1A Fast Recovery 3A 20V 1N5817 MBR120P SR102 1N5820 MBR320 SR302 30V 1N5818 MBR130P 11DQ03 SR103 1N5821 MBR330 31DQ03 SR303 1N5819 MBR140P 11DQ04 SR104 IN5822 MBR340 31DQ04 SR304 50V MBR150 11DQ05 SR105 MBR350 31DQ05 SR305 60V MBR160 11DQ06 SR106 MBR360 31DQ06 SR306 40V LM1575/LM2575/LM2575HV VR 1A 3A The following diodes are all rated to 100V The following diodes are all rated to 100V 11DF1 MUR110 HER102 31DF1 MURD310 HER302 FIGURE 8. Diode Selection Guide Inductor Code Inductor Value Schott (Note 15) Pulse Eng. (Note 16) Renco (Note 17) L100 100 H 67127000 PE-92108 RL2444 L150 150 H 67127010 PE-53113 RL1954 L220 220 H 67127020 PE-52626 RL1953 L330 330 H 67127030 PE-52627 RL1952 L470 470 H 67127040 PE-53114 RL1951 L680 680 H 67127050 PE-52629 RL1950 H150 150 H 67127060 PE-53115 RL2445 H220 220 H 67127070 PE-53116 RL2446 H330 330 H 67127080 PE-53117 RL2447 H470 470 H 67127090 PE-53118 RL1961 H680 680 H 67127100 PE-53119 RL1960 H1000 1000 H 67127110 PE-53120 RL1959 H1500 1500 H 67127120 PE-53121 RL1958 H2200 2200 H 67127130 PE-53122 RL2448 Note 15: Schott Corp., (612) 475-1173, 1000 Parkers Lake Rd., Wayzata, MN 55391. Note 16: Pulse Engineering, (619) 674-8100, P.O. Box 12236, San Diego, CA 92112. Note 17: Renco Electronics Inc., (516) 586-5566, 60 Jeffryn Blvd. East, Deer Park, NY 11729. FIGURE 9. Inductor Selection by Manufacturer's Part Number 17 www.national.com LM1575/LM2575/LM2575HV circuits, or can give incorrect scope readings because of induced voltages in the scope probe. The inductors listed in the selection chart include ferrite pot core construction for AIE, powdered iron toroid for Pulse Engineering, and ferrite bobbin core for Renco. An inductor should not be operated beyond its maximum rated current because it may saturate. When an inductor begins to saturate, the inductance decreases rapidly and the inductor begins to look mainly resistive (the DC resistance of the winding). This will cause the switch current to rise very rapidly. Different inductor types have different saturation characteristics, and this should be kept in mind when selecting an inductor. The inductor manufacturer's data sheets include current and energy limits to avoid inductor saturation. Application Hints INPUT CAPACITOR (CIN) To maintain stability, the regulator input pin must be bypassed with at least a 47 F electrolytic capacitor. The capacitor's leads must be kept short, and located near the regulator. If the operating temperature range includes temperatures below -25C, the input capacitor value may need to be larger. With most electrolytic capacitors, the capacitance value decreases and the ESR increases with lower temperatures and age. Paralleling a ceramic or solid tantalum capacitor will increase the regulator stability at cold temperatures. For maximum capacitor operating lifetime, the capacitor's RMS ripple current rating should be greater than INDUCTOR RIPPLE CURRENT When the switcher is operating in the continuous mode, the inductor current waveform ranges from a triangular to a sawtooth type of waveform (depending on the input voltage). For a given input voltage and output voltage, the peak-to-peak amplitude of this inductor current waveform remains constant. As the load current rises or falls, the entire sawtooth current waveform also rises or falls. The average DC value of this waveform is equal to the DC load current (in the buck regulator configuration). If the load current drops to a low enough level, the bottom of the sawtooth current waveform will reach zero, and the switcher will change to a discontinuous mode of operation. This is a perfectly acceptable mode of operation. Any buck switching regulator (no matter how large the inductor value is) will be forced to run discontinuous if the load current is light enough. INDUCTOR SELECTION All switching regulators have two basic modes of operation: continuous and discontinuous. The difference between the two types relates to the inductor current, whether it is flowing continuously, or if it drops to zero for a period of time in the normal switching cycle. Each mode has distinctively different operating characteristics, which can affect the regulator performance and requirements. The LM2575 (or any of the Simple Switcher family) can be used for both continuous and discontinuous modes of operation. The inductor value selection guides in Figure 3 through Figure 7 were designed for buck regulator designs of the continuous inductor current type. When using inductor values shown in the inductor selection guide, the peak-to-peak inductor ripple current will be approximately 20% to 30% of the maximum DC current. With relatively heavy load currents, the circuit operates in the continuous mode (inductor current always flowing), but under light load conditions, the circuit will be forced to the discontinuous mode (inductor current falls to zero for a period of time). This discontinuous mode of operation is perfectly acceptable. For light loads (less than approximately 200 mA) it may be desirable to operate the regulator in the discontinuous mode, primarily because of the lower inductor values required for the discontinuous mode. The selection guide chooses inductor values suitable for continuous mode operation, but if the inductor value chosen is prohibitively high, the designer should investigate the possibility of discontinuous operation. The computer design software Switchers Made Simple will provide all component values for discontinuous (as well as continuous) mode of operation. Inductors are available in different styles such as pot core, toriod, E-frame, bobbin core, etc., as well as different core materials, such as ferrites and powdered iron. The least expensive, the bobbin core type, consists of wire wrapped on a ferrite rod core. This type of construction makes for an inexpensive inductor, but since the magnetic flux is not completely contained within the core, it generates more electromagnetic interference (EMI). This EMI can cause problems in sensitive www.national.com OUTPUT CAPACITOR An output capacitor is required to filter the output voltage and is needed for loop stability. The capacitor should be located near the LM2575 using short pc board traces. Standard aluminum electrolytics are usually adequate, but low ESR types are recommended for low output ripple voltage and good stability. The ESR of a capacitor depends on many factors, some which are: the value, the voltage rating, physical size and the type of construction. In general, low value or low voltage (less than 12V) electrolytic capacitors usually have higher ESR numbers. The amount of output ripple voltage is primarily a function of the ESR (Equivalent Series Resistance) of the output capacitor and the amplitude of the inductor ripple current (IIND). See the section on inductor ripple current in Application Hints. The lower capacitor values (220 F-680 F) will allow typically 50 mV to 150 mV of output ripple voltage, while largervalue capacitors will reduce the ripple to approximately 20 mV to 50 mV. Output Ripple Voltage = (IIND) (ESR of COUT) To further reduce the output ripple voltage, several standard electrolytic capacitors may be paralleled, or a higher-grade capacitor may be used. Such capacitors are often called "high-frequency," "low-inductance," or "low-ESR." These will reduce the output ripple to 10 mV or 20 mV. However, when operating in the continuous mode, reducing the ESR below 0.05 can cause instability in the regulator. Tantalum capacitors can have a very low ESR, and should be carefully evaluated if it is the only output capacitor. Because of their good low temperature characteristics, a tantalum can 18 With the N or M packages, all the pins labeled ground, power ground, or signal ground should be soldered directly to wide printed circuit board copper traces. This assures both low inductance connections and good thermal properties. HEAT SINK/THERMAL CONSIDERATIONS In many cases, no heat sink is required to keep the LM2575 junction temperature within the allowed operating range. For each application, to determine whether or not a heat sink will be required, the following must be identified: CATCH DIODE Buck regulators require a diode to provide a return path for the inductor current when the switch is off. This diode should be located close to the LM2575 using short leads and short printed circuit traces. Because of their fast switching speed and low forward voltage drop, Schottky diodes provide the best efficiency, especially in low output voltage switching regulators (less than 5V). FastRecovery, High-Efficiency, or Ultra-Fast Recovery diodes are also suitable, but some types with an abrupt turn-off characteristic may cause instability and EMI problems. A fast-recovery diode with soft recovery characteristics is a better choice. Standard 60 Hz diodes (e.g., 1N4001 or 1N5400, etc.) are also not suitable. See Figure 8 for Schottky and "soft" fastrecovery diode selection guide. 1. 2. 3. Maximum ambient temperature (in the application). Maximum regulator power dissipation (in application). Maximum allowed junction temperature (150C for the LM1575 or 125C for the LM2575). For a safe, conservative design, a temperature approximately 15C cooler than the maximum temperature should be selected. 4. LM2575 package thermal resistances JA and JC. Total power dissipated by the LM2575 can be estimated as follows: PD = (VIN) (IQ) + (VO/VIN) (ILOAD) (VSAT) OUTPUT VOLTAGE RIPPLE AND TRANSIENTS The output voltage of a switching power supply will contain a sawtooth ripple voltage at the switcher frequency, typically about 1% of the output voltage, and may also contain short voltage spikes at the peaks of the sawtooth waveform. The output ripple voltage is due mainly to the inductor sawtooth ripple current multiplied by the ESR of the output capacitor. (See the inductor selection in the application hints.) The voltage spikes are present because of the fast switching action of the output switch, and the parasitic inductance of the output filter capacitor. To minimize these voltage spikes, special low inductance capacitors can be used, and their lead lengths must be kept short. Wiring inductance, stray capacitance, as well as the scope probe used to evaluate these transients, all contribute to the amplitude of these spikes. An additional small LC filter (20 H & 100 F) can be added to the output (as shown in Figure 15) to further reduce the amount of output ripple and transients. A 10 x reduction in output ripple voltage and transients is possible with this filter. where IQ (quiescent current) and VSAT can be found in the Characteristic Curves shown previously, VIN is the applied minimum input voltage, VO is the regulated output voltage, and ILOAD is the load current. The dynamic losses during turnon and turn-off are negligible if a Schottky type catch diode is used. When no heat sink is used, the junction temperature rise can be determined by the following: TJ = (PD) (JA) To arrive at the actual operating junction temperature, add the junction temperature rise to the maximum ambient temperature. TJ = TJ + TA If the actual operating junction temperature is greater than the selected safe operating junction temperature determined in step 3, then a heat sink is required. When using a heat sink, the junction temperature rise can be determined by the following: FEEDBACK CONNECTION The LM2575 (fixed voltage versions) feedback pin must be wired to the output voltage point of the switching power supply. When using the adjustable version, physically locate both output voltage programming resistors near the LM2575 to avoid picking up unwanted noise. Avoid using resistors greater than 100 k because of the increased chance of noise pickup. TJ = (PD) (JC + interface + Heat sink) The operating junction temperature will be: TJ = TA + TJ As above, if the actual operating junction temperature is greater than the selected safe operating junction temperature, then a larger heat sink is required (one that has a lower thermal resistance). When using the LM2575 in the plastic DIP (N) or surface mount (M) packages, several items about the thermal properties of the packages should be understood. The majority of the heat is conducted out of the package through the leads, with a minor portion through the plastic parts of the package. Since the lead frame is solid copper, heat from the die is readily conducted through the leads to the printed circuit board copper, which is acting as a heat sink. For best thermal performance, the ground pins and all the unconnected pins should be soldered to generous amounts of printed circuit board copper, such as a ground plane. Large areas of copper provide the best transfer of heat to the surrounding air. Copper on both sides of the board is also helpful in getting the heat away from the package, even if there is no direct copper contact between the two sides. Thermal resis- ON /OFF INPUT For normal operation, the ON /OFF pin should be grounded or driven with a low-level TTL voltage (typically below 1.6V). To put the regulator into standby mode, drive this pin with a high-level TTL or CMOS signal. The ON /OFF pin can be safely pulled up to +VIN without a resistor in series with it. The ON /OFF pin should not be left open. GROUNDING To maintain output voltage stability, the power ground connections must be low-impedance (see Figure 2). For the TO-3 style package, the case is ground. For the 5-lead TO-220 style package, both the tab and pin 3 are ground and either connection may be used, as they are both part of the same copper lead frame. 19 www.national.com LM1575/LM2575/LM2575HV be used in parallel with aluminum electrolytics, with the tantalum making up 10% or 20% of the total capacitance. The capacitor's ripple current rating at 52 kHz should be at least 50% higher than the peak-to-peak inductor ripple current. LM1575/LM2575/LM2575HV tance numbers as low as 40C/W for the SO package, and 30C/W for the N package can be realized with a carefully engineered pc board. Included on the Switchers Made Simple design software is a more precise (non-linear) thermal model that can be used to determine junction temperature with different input-output parameters or different component values. It can also calculate the heat sink thermal resistance required to maintain the regulators junction temperature below the maximum operating temperature. would allow the input voltage to rise to a high enough level before the switcher would be allowed to turn on. Because of the structural differences between the buck and the buck-boost regulator topologies, the buck regulator design procedure section can not be used to select the inductor or the output capacitor. The recommended range of inductor values for the buck-boost design is between 68 H and 220 H, and the output capacitor values must be larger than what is normally required for buck designs. Low input voltages or high output currents require a large value output capacitor (in the thousands of micro Farads). The peak inductor current, which is the same as the peak switch current, can be calculated from the following formula: Additional Applications INVERTING REGULATOR Figure 10 shows a LM2575-12 in a buck-boost configuration to generate a negative 12V output from a positive input voltage. This circuit bootstraps the regulator's ground pin to the negative output voltage, then by grounding the feedback pin, the regulator senses the inverted output voltage and regulates it to -12V. For an input voltage of 12V or more, the maximum available output current in this configuration is approximately 0.35A. At lighter loads, the minimum input voltage required drops to approximately 4.7V. The switch currents in this buck-boost configuration are higher than in the standard buck-mode design, thus lowering the available output current. Also, the start-up input current of the buck-boost converter is higher than the standard buck-mode regulator, and this may overload an input power source with a current limit less than 1.5A. Using a delayed turn-on or an undervoltage lockout circuit (described in the next section) Where fosc = 52 kHz. Under normal continuous inductor current operating conditions, the minimum VIN represents the worst case. Select an inductor that is rated for the peak current anticipated. Also, the maximum voltage appearing across the regulator is the absolute sum of the input and output voltage. For a -12V output, the maximum input voltage for the LM2575 is +28V, or +48V for the LM2575HV. The Switchers Made Simple (version 3.3) design software can be used to determine the feasibility of regulator designs using different topologies, different input-output parameters, different components, etc. 1147515 FIGURE 10. Inverting Buck-Boost Develops -12V www.national.com 20 LM1575/LM2575/LM2575HV NEGATIVE BOOST REGULATOR Another variation on the buck-boost topology is the negative boost configuration. The circuit in Figure 11 accepts an input voltage ranging from -5V to -12V and provides a regulated -12V output. Input voltages greater than -12V will cause the output to rise above -12V, but will not damage the regulator. Because of the boosting function of this type of regulator, the switch current is relatively high, especially at low input voltages. Output load current limitations are a result of the maximum current rating of the switch. Also, boost regulators can not provide current limiting load protection in the event of a shorted load, so some other means (such as a fuse) may be necessary. 1147517 Note: Complete circuit not shown. Note: Pin numbers are for the TO-220 package. FIGURE 12. Undervoltage Lockout for Buck Circuit 1147516 Typical Load Current 200 mA for VIN = -5.2V 500 mA for VIN = -7V Note: Pin numbers are for TO-220 package. 1147518 Note: Complete circuit not shown (see Figure 10). Note: Pin numbers are for the TO-220 package. FIGURE 11. Negative Boost UNDERVOLTAGE LOCKOUT In some applications it is desirable to keep the regulator off until the input voltage reaches a certain threshold. An undervoltage lockout circuit which accomplishes this task is shown in Figure 12, while Figure 13 shows the same circuit applied to a buck-boost configuration. These circuits keep the regulator off until the input voltage reaches a predetermined level. FIGURE 13. Undervoltage Lockout for Buck-Boost Circuit VTH VZ1 + 2VBE (Q1) DELAYED STARTUP The ON /OFF pin can be used to provide a delayed startup feature as shown in Figure 14. With an input voltage of 20V and for the part values shown, the circuit provides approximately 10 ms of delay time before the circuit begins switching. Increasing the RC time constant can provide longer delay times. But excessively large RC time constants can cause problems with input voltages that are high in 60 Hz or 120 Hz ripple, by coupling the ripple into the ON /OFF pin. 1147519 Note: Complete circuit not shown. Note: Pin numbers are for the TO-220 package. FIGURE 14. Delayed Startup ADJUSTABLE OUTPUT, LOW-RIPPLE POWER SUPPLY A 1A power supply that features an adjustable output voltage is shown in Figure 15. An additional L-C filter that reduces the output ripple by a factor of 10 or more is included in this circuit. 21 www.national.com LM1575/LM2575/LM2575HV 1147520 Note: Pin numbers are for the TO-220 package. FIGURE 15. 1.2V to 55V Adjustable 1A Power Supply with Low Output Ripple www.national.com 22 BUCK REGULATOR A switching regulator topology in which a higher voltage is converted to a lower voltage. Also known as a step-down switching regulator. OUTPUT RIPPLE VOLTAGE The AC component of the switching regulator's output voltage. It is usually dominated by the output capacitor's ESR multiplied by the inductor's ripple current (IIND). The peakto-peak value of this sawtooth ripple current can be determined by reading the Inductor Ripple Current section of the Application hints. BUCK-BOOST REGULATOR A switching regulator topology in which a positive voltage is converted to a negative voltage without a transformer. DUTY CYCLE (D) Ratio of the output switch's on-time to the oscillator period. CAPACITOR RIPPLE CURRENT RMS value of the maximum allowable alternating current at which a capacitor can be operated continuously at a specified temperature. STANDBY QUIESCENT CURRENT (ISTBY) Supply current required by the LM2575 when in the standby mode (ON /OFF pin is driven to TTL-high voltage, thus turning the output switch OFF). CATCH DIODE OR CURRENT STEERING DIODE The diode which provides a return path for the load current when the LM2575 switch is OFF. EFFICIENCY () The proportion of input power actually delivered to the load. INDUCTOR RIPPLE CURRENT (IIND) The peak-to-peak value of the inductor current waveform, typically a sawtooth waveform when the regulator is operating in the continuous mode (vs. discontinuous mode). CONTINUOUS/DISCONTINUOUS MODE OPERATION Relates to the inductor current. In the continuous mode, the inductor current is always flowing and never drops to zero, vs. the discontinuous mode, where the inductor current drops to zero for a period of time in the normal switching cycle. CAPACITOR EQUIVALENT SERIES RESISTANCE (ESR) The purely resistive component of a real capacitor's impedance (see Figure 16). It causes power loss resulting in capacitor heating, which directly affects the capacitor's operating lifetime. When used as a switching regulator output filter, higher ESR values result in higher output ripple voltages. INDUCTOR SATURATION The condition which exists when an inductor cannot hold any more magnetic flux. When an inductor saturates, the inductor appears less inductive and the resistive component dominates. Inductor current is then limited only by the DC resistance of the wire and the available source current. OPERATING VOLT MICROSECOND CONSTANT (E*Top) The product (in VoIt*s) of the voltage applied to the inductor and the time the voltage is applied. This E*Top constant is a measure of the energy handling capability of an inductor and is dependent upon the type of core, the core area, the number of turns, and the duty cycle. 1147521 FIGURE 16. Simple Model of a Real Capacitor Most standard aluminum electrolytic capacitors in the 100 F-1000 F range have 0.5 to 0.1 ESR. Higher-grade capacitors ("low-ESR", "high-frequency", or "low-inductance"') in the 100 F-1000 F range generally have ESR of less than 0.15. 23 www.national.com LM1575/LM2575/LM2575HV EQUIVALENT SERIES INDUCTANCE (ESL) The pure inductance component of a capacitor (see Figure 16). The amount of inductance is determined to a large extent on the capacitor's construction. In a buck regulator, this unwanted inductance causes voltage spikes to appear on the output. Definition of Terms LM1575/LM2575/LM2575HV Physical Dimensions inches (millimeters) unless otherwise noted 16-Lead Ceramic Dual-in-Line (J) Order Number LM1575J-3.3/883, LM1575J-5.0/883, LM1575J-12/883, LM1575J-15/883, or LM1575J-ADJ/883 NS Package Number J16A 24-Lead Wide Surface Mount (WM) Order Number LM2575M-5.0, LM2575HVM-5.0, LM2575M-12, LM2575HVM-12, LM2575M-15, LM2575HVM-15, LM2575M-ADJ or LM2575HVM-ADJ NS Package Number M24B www.national.com 24 LM1575/LM2575/LM2575HV 16-Lead Molded DIP (N) Order Number LM2575N-5.0, LM2575HVN-5.0, LM2575N-12, LM2575HVN-12, LM2575N-15, LM2575HVN-15, LM2575N-ADJ or LM2575HVN-ADJ NS Package Number N16A 5-Lead TO-220 (T) Order Number LM2575T-3.3, LM2575HVT-3.3, LM2575T-5.0, LM2575HVT-5.0, LM2575T-12, LM2575HVT-12, LM2575T-15, LM2575HVT-15, LM2575T-ADJ or LM2575HVT-ADJ NS Package Number T05A 25 www.national.com LM1575/LM2575/LM2575HV TO-263, Molded, 5-Lead Surface Mount Order Number LM2575S-3.3, LM2575HVS-3.3, LM2575S-5.0, LM2575HVS-5.0, LM2575S-12, LM2575HVS-12, LM2575S-15, LM2575HVS-15, LM2575S-ADJ or LM2575HVS-ADJ NS Package Number TS5B www.national.com 26 LM1575/LM2575/LM2575HV Bent, Staggered 5-Lead TO-220 (T) Order Number LM2575T-3.3 Flow LB03, LM2575HVT-3.3 Flow LB03, LM2575T-5.0 Flow LB03, LM2575HVT-5.0 Flow LB03, LM2575T-12 Flow LB03, LM2575HVT-12 Flow LB03, LM2575T-15 Flow LB03, LM2575HVT-15 Flow LB03, LM2575T-ADJ Flow LB03 or LM2575HVT-ADJ Flow LB03 NS Package Number T05D 27 www.national.com LM1575/LM2575/LM2575HV Series SIMPLE SWITCHER 1A Step-Down Voltage Regulator Notes THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2007 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530-85-86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +49 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated