4 ADC with PLL, 192 kHz, 24-Bit ADC AD1974 Data Sheet FEATURES GENERAL DESCRIPTION Phase-locked loop generated or direct master clock Low EMI design 107 dB dynamic range and SNR -94 dB THD + N Single 3.3 V supply Tolerance for 5 V logic inputs Supports 24 bits and 8 kHz to 192 kHz sample rates Differential ADC input SPI(R)-controllable for flexibility Software-controllable clickless mute Software power-down Right justified, left justified, I2S, and TDM modes Master and slave modes up to 16-channel input/output Available in a 48-lead LQFP Qualified for automotive applications The AD1974 is a high performance, single-chip ADC that provides four analog-to-digital converters (ADCs) with differential inputs using the Analog Devices, Inc. patented multibit sigmadelta (-) architecture. An SPI port is included, allowing a microcontroller to enable mutes and adjust many other parameters. The AD1974 operates from 3.3 V digital and analog supplies. The AD1974 is available in a single-ended output 48-lead LQFP. The AD1974 is designed for low EMI. This consideration is apparent in both the system and circuit design architectures. By using the on-board phase-locked loop (PLL) to derive the master clock from the LR clock or from an external crystal, the AD1974 eliminates the need for a separate high frequency master clock and can also be used with a suppressed bit clock. The ADCs are designed using the latest continuous time architectures from Analog Devices to further minimize EMI. By using 3.3 V supplies, power consumption is minimized, further reducing emissions. APPLICATIONS Automotive audio systems Home Theater Systems Set-top boxes Digital audio effects processors FUNCTIONAL BLOCK DIAGRAM DIGITAL AUDIO INPUT/OUTPUT AD1974 SERIAL DATA PORT ANALOG AUDIO INPUTS ADC ADC QUAD DEC FILTER 48kHz/ 96kHz/192kHz CLOCKS TIMING MANAGEMENT AND CONTROL (CLOCK AND PLL) ADC PRECISION VOLTAGE REFERENCE SDATA OUT CONTROL PORT SPI 12.48MHz CONTROL DATA INPUT/OUTPUT 06614-001 ADC Figure 1. Rev. D Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 (c)2007-2013 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com AD1974 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Theory of Operation ...................................................................... 11 Applications ....................................................................................... 1 Analog-to-Digital Converters (ADCs) .................................... 11 General Description ......................................................................... 1 Clock Signals ............................................................................... 11 Functional Block Diagram .............................................................. 1 Reset and Power-Down ............................................................. 11 Revision History ............................................................................... 2 Serial Control Port ..................................................................... 12 Specifications..................................................................................... 3 Power Supply and Voltage Reference....................................... 12 Test Conditions ............................................................................. 3 Serial Data Ports--Data Format ............................................... 12 Analog Performance Specifications ........................................... 3 TDM Modes ................................................................................ 13 Crystal Oscillator Specifications................................................. 4 Daisy-Chain Mode ..................................................................... 14 Digital Input/Output Specifications........................................... 4 Control Registers ............................................................................ 18 Power Supply Specifications........................................................ 5 PLL and Clock Control Registers ............................................. 18 Digital Filters ................................................................................. 5 AUXPORT Control Registers ................................................... 19 Timing Specifications .................................................................. 5 ADC Control Registers.............................................................. 20 Absolute Maximum Ratings ............................................................ 7 Additional Modes ....................................................................... 21 Thermal Resistance ...................................................................... 7 Application Circuits ....................................................................... 23 ESD Caution .................................................................................. 7 Outline Dimensions ....................................................................... 24 Pin Configuration and Function Descriptions ............................. 8 Ordering Guide .......................................................................... 24 Typical Performance Characteristics ........................................... 10 Automotive Products ................................................................. 24 REVISION HISTORY 3/13--Rev. C to Rev. B 11/09--Rev. 0 to Rev. A Change to tCLH Parameter, Table 7 ................................................... 6 Changes to Serial Control Port Section ........................................12 Changed Codec to ADC ............................................... Throughout Changes to Features and General Description Sections ..............1 Changes to Clock Signals Section ................................................ 11 Changes to Figure 12 and Figure 13 ............................................ 16 Changes to Control Registers Section ......................................... 18 2/11--Rev. B to Rev. C Changes to Features Section............................................................ 1 Changes to Ordering Guide .......................................................... 24 Added Automotive Products Section .......................................... 24 4/07--Revision 0: Initial Version 6/10--Rev. A to Rev. B Changed 130C to 125C Throughout........................................... 4 Changed TA to TC Throughout ....................................................... 4 Changes to Endnote 2 in Ordering Guide .................................. 24 Rev. D | Page 2 of 24 Data Sheet AD1974 SPECIFICATIONS TEST CONDITIONS Performance of all channels is identical, exclusive of the interchannel gain mismatch and interchannel phase deviation specifications. Supply Voltages (AVDD, DVDD) 3.3 V Temperature Range 1 As specified in Table 1 and Table 2 Master Clock 12.288 MHz (48 kHz fS, 256 x fS mode) Input Sample Rate 48 kHz Measurement Bandwidth 20 Hz to 20 kHz Word Width 24 bits Load Capacitance (Digital Output) 20 pF Load Current (Digital Output) 1 mA or 1.5 k to 1/2 DVDD supply Input Voltage High 2.0 V Input Voltage Low 0.8 V 1 Functionally guaranteed at -40C to +125C case temperature. ANALOG PERFORMANCE SPECIFICATIONS Specifications guaranteed at 25C (ambient). Table 1. Parameter ANALOG-TO-DIGITAL CONVERTERS ADC Resolution Full-Scale Input Voltage (Differential) Dynamic Range No Filter (RMS) With A-Weighted Filter (RMS) Total Harmonic Distortion + Noise (THD + N) Gain Error Interchannel Gain Mismatch Offset Error Gain Drift Interchannel Isolation CMRR Input Resistance Input Capacitance Input Common-Mode Bias Voltage REFERENCE Internal Reference Voltage External Reference Voltage Common-Mode Reference Output Conditions Min All ADCs Typ Max Unit 24 1.9 Bits V rms 102 105 -96 dB dB dB % dB mV ppm/C dB dB dB k pF V 20 Hz to 20 kHz, -60 dB input 98 100 -1 dBFS -10 -0.25 -10 100 mV rms, 1 kHz 100 mV rms, 20 kHz FILTR pin FILTR pin CM pin 1.32 Rev. D | Page 3 of 24 0 100 -110 55 55 14 10 1.5 1.50 1.50 1.50 -87 +10 +0.25 +10 1.68 V V V AD1974 Data Sheet Specifications measured at 125C (case). Table 2. Parameter ANALOG-TO-DIGITAL CONVERTERS ADC Resolution Full-Scale Input Voltage (Differential) Dynamic Range No Filter (RMS) With A-Weighted Filter (RMS) Total Harmonic Distortion + Noise (THD + N) Gain Error Interchannel Gain Mismatch Offset Error REFERENCE Internal Reference Voltage External Reference Voltage Common-Mode Reference Output Conditions Min All ADCs Typ Max Unit 24 1.9 Bits V rms 102 105 -96 dB dB dB % dB mV 20 Hz to 20 kHz, -60 dB input 95 97 -1 dBFS -10 -0.25 -10 FILTR pin FILTR pin CM pin 1.32 0 1.50 1.50 1.50 -87 +10 +0.25 +10 1.68 V V V CRYSTAL OSCILLATOR SPECIFICATIONS Table 3. Parameter Transconductance Min Typ 3.5 Max Unit Mmhos DIGITAL INPUT/OUTPUT SPECIFICATIONS -40C < TC < +125C, DVDD = 3.3 V 10%. Table 4. Parameter Input Voltage High (VIH) Input Voltage High (VIH) Input Voltage Low (VIL) Input Leakage High Level Output Voltage (VOH) Low Level Output Voltage (VOL) Input Capacitance Conditions/Comments MCLKI pin IIH @ VIH = 2.4 V IIL @ VIL = 0.8 V IOH = 1 mA IOL = 1 mA Rev. D | Page 4 of 24 Min 2.0 2.2 Typ Max 0.8 10 10 DVDD - 0.60 0.4 5 Unit V V V A A V V pF Data Sheet AD1974 POWER SUPPLY SPECIFICATIONS Table 5. Parameter SUPPLIES Voltage Digital Current Normal Operation Power-Down Analog Current Normal Operation Power-Down DISSIPATION Operation All Supplies Digital Supply Analog Supply Power-Down, All Supplies POWER SUPPLY REJECTION RATIO Signal at Analog Supply Pins Conditions/Comments Min Typ Max Unit DVDD AVDD MCLK = 256 fS fS = 48 kHz fS = 96 kHz fS = 192 kHz fS = 48 kHz to 192 kHz 3.0 3.0 3.3 3.3 3.6 3.6 V V 56 65 95 2.0 mA mA mA mA 74 23 mA mA 429 185 244 83 mW mW mW mW 50 50 dB dB MCLK = 256 fS, 48 kHz 1 kHz, 200 mV p-p 20 kHz, 200 mV p-p DIGITAL FILTERS Table 6. Parameter ADC DECIMATION FILTER Pass Band Pass-Band Ripple Transition Band Stop Band Stop-Band Attenuation Group Delay Mode All modes @ 48 kHz Factor Min 0.4375 fS Typ Max Unit 21 0.015 24 27 0.5 fS 0.5625 fS kHz dB kHz kHz dB s 79 22.9844 fS 479 TIMING SPECIFICATIONS -40C < TC < +125C, DVDD = 3.3 V 10%. Table 7. Parameter INPUT MASTER CLOCK (MCLK) AND RESET tMH tMH fMCLK fMCLK tPDR tPDRR Condition Comments Min Max Unit MCLK duty cycle ADC clock source = PLL clock @ 256 fS, 384 fS, 512 fS, 768 fS ADC clock source = direct MCLK @ 512 fS (bypass on-chip PLL) PLL mode, 256 fS reference Direct 512 fS mode 40 40 60 60 % % 6.9 13.8 27.6 MHz MHz ns tMCLK MCLK frequency Low Recovery Reset to active output Rev. D | Page 5 of 24 15 4096 AD1974 Parameter PLL Lock Time 256 fS VCO Clock Output Duty Cycle MCLK_O Pin SPI PORT tCCH tCCL fCCLK tCDS tCDH tCLS tCLH tCLHIGH tCOE tCOD tCOH tCOTS ADC SERIAL PORT tABH tABL tALS tALH tALS tABDD AUXILIARY INTERFACE tXDS tXDH tXBH tXBL tXLS tXLH Data Sheet Condition Comments Min Max Unit 40 10 60 ms % 10 ns ns MHz MCLK and LRCLK input See Figure 5 CCLK high CCLK low CCLK frequency CDATA setup CDATA hold Setup Hold High COUT enable COUT delay COUT hold COUT tristate ABCLK high ABCLK low ALRCLK setup ALRCLK hold ALRCLK skew ASDATA delay AAUXDATA setup AAUXDATA hold AUXBCLK high AUXBCLK low AUXLRCLK setup AUXLRCLK hold 35 35 fCCLK = 1/tCCP; only tCCP shown in Figure 5 To CCLK rising From CCLK rising To CCLK rising From CCLK rising Not shown in Figure 5 From CCLK falling From CCLK falling From CCLK falling, not shown in Figure 5 From CCLK falling See Figure 13 Slave mode Slave mode To ABCLK rising, slave mode From ABCLK rising, slave mode From ABCLK falling, master mode From ABCLK falling See Figure 12 To AUXBCLK rising From AUXBCLK rising To AUXBCLK rising From AUXBCLK rising Rev. D | Page 6 of 24 10 10 10 10 10 30 ns ns ns ns ns ns ns ns ns +8 18 ns ns ns ns ns ns 30 30 30 10 10 10 5 -8 10 5 10 10 10 5 ns ns ns ns ns ns Data Sheet AD1974 ABSOLUTE MAXIMUM RATINGS Table 8. Parameter Analog (AVDD) Digital (DVDD) Input Current (Except Supply Pins) Analog Input Voltage (Signal Pins) Digital Input Voltage (Signal Pins) Operating Temperature Range (Case) Storage Temperature Range Rating -0.3 V to +3.6 V -0.3 V to +3.6 V 20 mA -0.3 V to AVDD + 0.3 V -0.3 V to DVDD + 0.3 V -40C to +125C -65C to +150C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. THERMAL RESISTANCE JA represents thermal resistance, junction-to-ambient; JC represents the thermal resistance, junction-to-case. All characteristics are for a 4-layer board. Table 9. Package Type 48-Lead LQFP ESD CAUTION Rev. D | Page 7 of 24 JA 50.1 JC 17 Unit C/W AD1974 Data Sheet AVDD 41 CM 42 ADC1LN 43 ADC1LP 44 ADC1RP 45 ADC2LP ADC2LN 46 ADC1RN ADC2RN 47 ADC2RP AVDD 48 40 39 38 37 1 36 AGND MCLKI/XI 2 35 FILTR MCLKO/XO 3 34 AGND AGND 4 33 AVDD AVDD 5 AD1974 32 AGND NC 6 NC TOP VIEW (Not to Scale) 7 NC 8 29 NC NC 9 28 NC PD/RST 10 27 CLATCH SINGLE-ENDED OUTPUT 31 NC 30 NC 17 18 19 20 21 22 23 24 ASDATA1 ABCLK ALRCLK CIN COUT 16 ASDATA2 15 AUXBCLK 14 AUXLRCLK DVDD 13 NC CCLK DGND AUXDATA1 26 25 AUXDATA2 NC 11 DGND 12 NC = NO CONNECT 06614-020 AGND LF PIN CONFIGURATION AND FUNCTION DESCRIPTIONS Figure 2. AD1974 Single-Ended Output, 48-Lead LQFP Pin Configuration Table 10. Pin Function Description Pin No. 1, 4, 32, 34, 36 2 3 5, 33, 37, 48 6 to 9, 11, 16, 28 to 31 10 12, 25 13 14 15 17 18 19 20 21 22 23 24 26 27 35 38 39 40 41 42 43 Type 1 I I O I I I I I/O I/O I/O I/O I/O O I/O I/O I I/O I I O O I I I I I Mnemonic AGND MCLKI/XI MCLKO/XO AVDD NC PD/RST DGND DVDD AUXDATA2 AUXDATA1 AUXBCLK AUXLRCLK ASDATA2 ASDATA1 ABCLK ALRCLK CIN COUT CCLK CLATCH FILTR CM ADC1LP ADC1LN ADC1RP ADC1RN ADC2LP Description Analog Ground. Master Clock Input/Crystal Oscillator Input. Master Clock Output/Crystal Oscillator Output. Analog Power Supply. Connect to analog 3.3 V supply. No Connect. Power-Down/Reset (Active Low). Digital Ground. Digital Power Supply. Connect to digital 3.3 V supply. Auxiliary Data Input 2 (From External ADC 2). Auxiliary Data Input 1 (From External ADC 1). Auxiliary Bit Clock. Auxiliary Left-Right Framing Clock. ADC Serial Data Output 2 (ADC 2 Left and ADC 2 Right)/ADC TDM Data Input. ADC Serial Data Output 1 (ADC 1 Left and ADC 1 Right)/ADC TDM Data Output. Serial Bit Clock for ADCs. Left-Right Framing Clock for ADCs. Control Data Input (SPI). Control Data Output (SPI). Control Clock Input (SPI). Latch Input for Control Data (SPI). Voltage Reference Filter Capacitor Connection. Bypass with 10 F||100 nF to AGND. Common-Mode Reference Filter Capacitor Connection. Bypass with 47 F||100 nF to AGND. ADC1 Left Positive Input. ADC1 Left Negative Input. ADC1 Right Positive Input. ADC1 Right Negative Input. ADC2 Left Positive Input. Rev. D | Page 8 of 24 Data Sheet Pin No. 44 45 46 47 1 AD1974 Type 1 I I I O Mnemonic ADC2LN ADC2RP ADC2RN LF Description ADC2 Left Negative Input. ADC2 Right Positive Input. ADC2 Right Negative Input. PLL Loop Filter, Return to AVDD. I = input, O = output. Rev. D | Page 9 of 24 AD1974 Data Sheet TYPICAL PERFORMANCE CHARACTERISTICS 0 -10 0.06 -20 0.04 -30 MAGNITUDE (dB) 0.08 0.02 0 -0.02 -40 -50 -60 -0.06 -80 -0.08 -90 -0.10 0 2000 4000 6000 8000 10000 12000 14000 16000 18000 FREQUENCY (kHz) -100 0 5000 10000 15000 20000 25000 30000 35000 40000 FREQUENCY (kHz) Figure 4. ADC Stop-Band Filter Response, 48 kHz Figure 3. ADC Pass-Band Filter Response, 48 kHz Rev. D | Page 10 of 24 06614-003 -70 -0.04 06614-002 MAGNITUDE (dB) 0.10 Data Sheet AD1974 THEORY OF OPERATION ANALOG-TO-DIGITAL CONVERTERS (ADCS) There are four ADC channels in the AD1974 configured as two stereo pairs with differential inputs. The ADCs can operate at a nominal sample rate of 48 kHz, 96 kHz, or 192 kHz. The ADCs include on-board digital antialiasing filters with a 79 dB stopband attenuation and a linear phase response, operating at an oversampling ratio of 128 (48 kHz, 96 kHz, and 192 kHz modes). Digital outputs are supplied through two serial data output pins (one for each stereo pair) as well as a common frame (ALRCLK) and bit clock (ABCLK). Alternatively, one of the time division multiplexed (TDM) modes can be used to access up to 16 channels on a single TDM data line. The ADCs must be driven from a differential signal source for best performance. The input pins of the ADCs connect to internal switched capacitors. To isolate the external driving op amp from the glitches caused by the internal switched capacitors, each input pin should be isolated by using a series connected, external, 100 resistor together with a 1 nF capacitor connected from each input to ground. This capacitor must be of high quality, for instance, a ceramic NP0 capacitor or a polypropylene film capacitor. The differential inputs have a nominal common-mode voltage of 1.5 V. The voltage at the common-mode reference pin (CM) can be used to bias external op amps to buffer the input signals (see the Power Supply and Voltage Reference section). The inputs can also be ac-coupled and do not need an external dc bias to CM. A digital high-pass filter can be switched in line with the ADCs under serial control to remove residual dc offsets. It has a 1.4 Hz, 6 dB per octave cutoff at a 48 kHz sample rate. The cutoff frequency scales directly with sample frequency. The voltage at CM can be used to bias the external op amps that buffer the output signals (see the Power Supply and Voltage Reference section). CLOCK SIGNALS The on-chip PLL can be selected to reference the input sample rate from either the LRCLK or AUXLRCK pins or 256, 384, 512, or 768 times the sample rate, referenced to the 48 kHz mode from the MCLKI/XI pin. The default at power-up is 256 x fS from MCLKI. In 96 kHz mode, the master clock frequency stays at the same absolute frequency; therefore, the actual multiplication rate is divided by 2. In 192 kHz mode, the actual multiplication rate is divided by 4. For example, if the AD1974 is programmed in 256 x fS mode, the frequency of the master clock input is 256 x 48 kHz = 12.288 MHz. If the AD1974 is then switched to 96 kHz operation (by writing to the SPI port), the frequency of the master clock should remain at 12.288 MHz (128 x fS). In 192 kHz mode, this becomes 64 x fS. The internal clock for the ADCs is 256 x fS for all clock modes. By default, the on-board PLL generates this internal master clock from an external clock. A direct 512 x fS (referenced to 48 kHz mode) master clock can be used for the ADCs if selected in the PLL and Clock Control 1 register. Note that it is not possible to use a direct clock for the ADCs set to the 192 kHz mode. It is required that the on-chip PLL be used in this mode. The PLL can be powered down in the PLL and Clock Control 0 register. To ensure reliable locking when changing PLL modes, or if the reference clock is unstable at power-on, power down the PLL and then power it back up when the reference clock has stabilized. The internal MCLK can be disabled in the PLL and Clock Control 0 register to reduce power dissipation when the AD1974 is idle. The clock should be stable before it is enabled. Unless a standalone mode is selected (see the Serial Control Port section), the clock is disabled by reset and must be enabled by writing to the SPI port for normal operation. To maintain the highest performance possible, it is recommended that the clock jitter of the internal master clock signal be limited to less than 300 ps rms time interval error (TIE). Even at these levels, extra noise or tones can appear in the outputs if the jitter spectrum contains large spectral peaks. If the internal PLL is not being used, it is highly recommended that an independent crystal oscillator generate the master clock. In addition, it is especially important that the clock signal should not be passed through an FPGA, CPLD, DSP, or other large digital chip before being applied to the AD1974. In most cases, this induces clock jitter due to the sharing of common power and ground connections with other unrelated digital output signals. When the PLL is used, jitter in the reference clock is attenuated above a certain frequency depending on the loop filter. RESET AND POWER-DOWN The reset pin sets all the control registers to their default settings. To avoid pops, reset does not power down the analog outputs. After reset is deasserted, and the PLL acquires a lock condition, an initialization routine runs inside the AD1974. This initialization lasts for approximately 256 master clock cycles. The PLL and Clock Control 0 register and the ADC Control 1 register power down their respective sections using power down bits. All other register settings are retained. The PD/RST pin should be pulled low by an external resistor to guarantee proper startup. Rev. D | Page 11 of 24 AD1974 Data Sheet Table 11. Standalone Mode Selection ADC Clocks Slave Master CIN 0 0 COUT 0 1 tCLS CLATCH 0 0 tCLH tCCH tCCL tCCP CLATCH CCLK 0 0 tCOTS CCLK tCDS tCDH COUT D23 D22 D9 tCOE D9 D8 D0 D8 D0 06614-010 CIN tCOD Figure 5. Format of the SPI Signal SERIAL CONTROL PORT The AD1974 has an SPI control port that permits programming and reading back of the internal control registers for the ADCs, DACs, and clock system. A standalone mode is also available for operation without serial control; standalone is configured at reset by connecting CIN, CCLK, and CLATCH to ground. In standalone mode, all registers are set to default, except the internal MCLK enable, which is set to 1. The ADC, ABCLK, and ALRCLK clock ports are set to master/slave by the connecting the COUT pin to either DVDD or ground. Standalone mode only supports stereo mode with an I2S data format and 256 fS MCLK rate. Refer to Table 11 for details. If CIN, CCLK, and CLATCH are not grounded, the AD1974 SPI port is active. It is recommended to use a weak pull-up resistor on CLATCH in applications that have a microcontroller. This pull-up resistor ensures that the AD1939 recognizes the presence of a microcontroller. The SPI control port of the AD1974 is a 4-wire serial control port. The format is similar to that of the Motorola SPI(R) format except that the input data-word is 24 bits wide. The serial bit clock and latch can be completely asynchronous to the sample rate of the ADCs. Figure 5 shows the format of the SPI signal. The first byte is a global address with a read/write bit. For the AD1974, the address is 0x04, shifted left one bit due to the R/W bit. The second byte is the AD1974 register address and the third byte is the data. POWER SUPPLY AND VOLTAGE REFERENCE The AD1974 is designed for 3.3 V supplies. Separate power supply pins (Pin 5, Pin 13, Pin 33, Pin 37, and Pin 38) are provided for the analog and digital sections. These pins should be bypassed with 100 nF ceramic chip capacitors, as close to the pins as possible, to minimize noise pickup. A bulk aluminum electrolytic capacitor of at least 22 F should also be placed on the same PC board as the ADC. For critical applications, improved performance is obtained with separate supplies for the analog and digital sections. If this is not possible, it is rec- ommended that the analog and digital supplies be isolated by means of a ferrite bead in series with each supply. It is important that the analog supply be as clean as possible. All digital inputs are compatible with TTL and CMOS levels. All outputs are driven from the 3.3 V DVDD supply and are compatible with TTL and 3.3 V CMOS levels. The ADC internal voltage reference (VREF) is brought out on FILTR and should be bypassed as close as possible to the AD1974 with a parallel combination of 10 F and 100 nF. Any external current drawn should be limited to less than 50 A. VREF can be disabled in the PLL and Clock Control 1 register and FILTR can be driven from an external source. The ADC input gain varies by the inverse ratio. CM is the internal common-mode reference. It should be bypassed as close as possible to the AD1974, with a parallel combination of 47 F and 100 nF. This voltage can be used to bias external op amps to the common-mode voltage of the input and output signal pins. The output current should be limited to less than 0.5 mA source and 2 mA sink. SERIAL DATA PORTS--DATA FORMAT The four ADC channels use a common serial bit clock (ABCLK) and a left-right framing clock (ALRCLK) in the serial data port. The clock signals are all synchronous with the sample rate. The normal stereo serial modes are shown in Figure 11. The ADC serial data modes default to I2S. The ports can also be programmed for left justified, right justified, and TDM modes. The word width is 24 bits by default and can be programmed for 16 or 20 bits. The ADC serial formats and serial clock polarity are programmable according to the ADC Control 1 register. The ADC serial ports are programmable to become the bus masters according to the ADC Control 2 register. By default, both ADC serial ports are in the slave mode. Rev. D | Page 12 of 24 Data Sheet AD1974 The AD1974 serial ports also have several different TDM serial data modes. The first and most commonly used configuration is shown in Figure 6 where the ADC serial port outputs one data stream consisting of four on-chip ADCs followed by four unused slots. In this mode, ABCLK is set to 256 fS (8-channel TDM mode). put stream follow four on-chip ADC channel slots. It should be noted that due to the high ABCLK frequency, this mode is available only in the 48 kHz/44.1 kHz/32 kHz sample rate. ALRCLK 256 BCLKs ABCLK ADATA 32 BCLKs SLOT 1 LEFT 1 SLOT 2 RIGHT 1 SLOT 3 LEFT 2 SLOT 4 RIGHT 2 UNUSED UNUSED UNUSED UNUSED The I/O pins of the serial ports are defined according to the serial mode selected. For a detailed description of the function of each pin in TDM and AUX Modes, see Table 12. ALRCLK ABCLK MSB The AD1974 allows system configurations with more than four ADC channels (see Figure 7 and Figure 8) that use 8 ADCs and 16 ADCs. In this mode, four AUX channel slots in the TDM out- MSB-1 MSB-2 06614-016 TDM MODES ADATA Figure 6. ADC TDM (8-Channel I2S Mode) Table 12. Pin Function Changes in TDM and AUX Modes Pin Name ASDATA1 ASDATA2 AUXDATA1 AUXDATA2 ALRCLK ABCLK AUXLRCLK AUXBCLK Stereo Mode ADC1 data output ADC2 data output Not used (ground) Not used (ground) ADC LRCLK input/output ADC BCLK input/output Not used (ground) Not used (ground) TDM Mode ADC TDM data output ADC TDM data input Not used (ground) Not used (ground) ADC TDM frame sync input/output ADC TDM BCLK input/output Not used (ground) Not used (ground) AUX Mode ADCTDM data output Not used (float) AUXDATA in 1 (from external ADC1) AUXDATA in 2 (from external ADC2) ADCTDM frame sync input/output ADCTDM BCLK input/output AUXLRCLK input/output AUXBCLK input/output ALRCLK ABCLK ASDATA1 (TDM_OUT) FOUR-AUX ADC CHANNELS FOUR-ON-CHIP DAC CHANNELS ADCL1 ADCR1 ADCL2 ADCR2 AUXL1 AUXR1 AUXL2 AUXR2 32 BITS MSB AUXLRCLK (AUX PORT) LEFT RIGHT AUXDATA1 (AUX1_IN) MSB MSB AUXDATA2 (AUX2_IN) MSB MSB Figure 7. 8-Channel AUX ADC Mode Rev. D | Page 13 of 24 06614-050 AUXBCLK (AUX PORT) AD1974 Data Sheet ALRCLK ABCLK ASDATA1 (TDM_OUT) FOUR-ON-CHIP ADC CHANNELS ADCL1 ADCR1 ADCL2 AUXILIARY ADC CHANNELS ADCR2 AUXL1 AUXR1 AUXL2 UNUSED SLOTS AUXR2 UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED 32 BITS MSB AUXLRCLK (AUX PORT) LEFT RIGHT AUXDATA1 (AUX1_IN) MSB MSB AUXDATA2 (AUX2_IN) MSB MSB 06614-052 AUXBCLK (AUX PORT) Figure 8. 16-Channel AUX ADC Mode AD1974 must be grounded in all modes of operation. The second AD1974 is the device attached to the DSP TDM port. DAISY-CHAIN MODE The AD1974 also allows a daisy-chain configuration to expand the system to 8 ADCs and 16 ADCs (see Figure 9 and Figure 10). There are two configurations for the ADC port to work in daisy-chain mode. The first one is with an ABCLK at 256 fS shown in Figure 9. The second configuration is with an ABCLK at 512 fS shown in Figure 10. Note that in the 512 fS ABCLK mode, the ADC channels occupy the first eight slots, the second eight slots are empty. The TDM_IN of the first The I/O pins of the serial ports are defined according to the serial mode selected. See Table 13 for a detailed description of the function of each pin. See Figure 14 for a typical AD1974 configuration with two external stereo ADCs. Figure 11 through Figure 13 show the serial mode formats. For maximum flexibility, the polarity of LRCLK and BCLK are programmable. All of the clocks are shown with their normal polarity. The default mode is I2S. ALRCLK ABCLK ASDATA1 (TDM_OUT OF THE SECOND AD1974 IN THE CHAIN) ASDATA2 (TDM_IN OF THE SECOND AD1974 IN THE CHAIN) FOUR ADC CHANNELS OF THE SECOND IC IN THE CHAIN ADCL1 ADCR1 ADCL2 ADCR2 ADCL1 ADCR1 ADCL2 ADCR2 FOUR ADC CHANNELS OF THE FIRST IC IN THE CHAIN ADCL1 ADCR1 ADCL2 ADCR2 32 BITS SECOND AD1974 DSP MSB Figure 9. ADC TDM Daisy-Chain Mode (256 fS ABCLK, Two AD1974 Daisy Chains) Rev. D | Page 14 of 24 06614-056 FIRST AD1974 Data Sheet AD1974 ALRCLK ABCLK ASDATA1 (TDM_OUT OF THE SECOND AD1974 IN THE CHAIN) ASDATA2 (TDM_IN OF THE SECOND AD1974 IN THE CHAIN) FOUR ADC CHANNELS OF THE SECOND IC IN THE CHAIN FOUR ADC CHANNELS OF THE FIRST IC IN THE CHAIN ADCL1 ADCR1 ADCL2 ADCR2 ADCL1 ADCR1 ADCL2 ADCR2 UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED ADCL1 ADCR1 ADCL2 ADCR2 UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED UNUSED 32 BITS SECOND AD1974 DSP 06614-057 FIRST AD1974 MSB Figure 10. ADC TDM Daisy-Chain Mode (512 fS ABCLK, Two AD1974 Daisy Chains) LEFT CHANNEL ALRCLK RIGHT CHANNEL ABCLK ASDATA MSB MSB LSB LSB LEFT JUSTIFIED MODE--16 BITS TO 24 BITS PER CHANNEL LEFT CHANNEL ALRCLK RIGHT CHANNEL ABCLK ASDATA MSB MSB LSB LSB I2S MODE--16 BITS TO 24 BITS PER CHANNEL LEFT CHANNEL ALRCLK RIGHT CHANNEL ABCLK ASDATA MSB MSB LSB LSB RIGHT JUSTIFIED MODE--SELECT NUMBER OF BITS PER CHANNEL ALRCLK ABCLK MSB MSB LSB LSB DSP MODE--16 BITS TO 24 BITS PER CHANNEL 1/fS NOTES 1. DSP MODE DOES NOT IDENTIFY CHANNEL. 2. LRCLK NORMALLY OPERATES AT fS EXCEPT FOR DSP MODE WHICH IS 2 x fS. 3. BCLK FREQUENCY IS NORMALLY 64 x LRCLK BUT MAY BE OPERATED IN BURST MODE. Figure 11. Stereo Serial Modes Rev. D | Page 15 of 24 06614-013 ASDATA AD1974 Data Sheet tXBH AUXBCLK tXBL tXLH tXLS AUXRCLK tXDS AUXDATA LEFT JUSTIFIED MODE MSB MSB-1 tXDH tXDS AUXDATA I2S JUSTIFIED MODE MSB tXDH tXDS MSB LSB tXDH tXDH 06614-014 tXDS AUXDATA RIGHT JUSTIFIED MODE Figure 12. Auxiliary Serial Timing tABH ABCLK tABL tALH tALS ALRCLK tABDD ASDATA LEFT JUSTIFIED MODE MSB MSB-1 tABDD ASDATA I2S JUSTIFIED MODE MSB ASDATA RIGHT JUSTIFIED MODE MSB LSB 06614-015 tABDD Figure 13. ADC Serial Timing Table 13. Pin Function Changes in TDM and AUX Modes (Replication of Table 12) Pin Name ASDATA1 ASDATA2 AUXDATA1 AUXDATA2 ALRCLK ABCLK AUXLRCLK AUXBCLK Stereo Mode ADC1 data output ADC2 data output Not used (ground) Not used (ground) ADC LRCLK input/output ADC BCLK input/output Not used (ground) Not used (ground) TDM Mode ADC TDM data output ADC TDM data input Not used (ground) Not used (ground) ADC TDM Frame Sync input/output ADC TDM BCLK input/output Not used (ground) Not used (ground) Rev. D | Page 16 of 24 AUX Mode ADCTDM data output Not used (float) AUXDATA in 1 (from external ADC1) AUXDATA in 2 (from external ADC2) ADCTDM frame sync input/output ADCTDM BCLK input/output AUXLRCLK input/output AUXBCLK input/output Data Sheet AD1974 SHARC IS RUNNING IN SLAVE MODE (INTERRUPT-DRIVEN) TxCLK TFS (NC) RxDATA SHARC RxCLK 12.288MHz FSYNC-TDM (RFS) 30MHz LRCLK AUX ADC 1 BCLK DATA ASDATA1 ALRCLK ABCLK MCLK AUXLRCLK AD1974 BCLK AUXDATA1 DATA AUXDATA2 TDM MASTER AUX MASTER MCLK MCLK LRCLK AUX ADC 2 06614-019 AUXBCLK Figure 14. Example of AUX Mode Connection to SHARC(R) (AD1974 as TDM Master/AUX Master Shown) Rev. D | Page 17 of 24 AD1974 Data Sheet CONTROL REGISTERS The global address for the AD1974 is 0x04, shifted left one bit due to the R/W bit. All registers are reset to 0. Note that the first setting in each control register parameter is the default setting. Table 14. Register Format Bit Global Address R/W Register Address Data 23:17 16 15:8 7:0 Table 15. Register Addresses Description Address 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Function PLL and Clock Control 0 PLL and Clock Control 1 AUXPORT Control 0 AUXPORT Control 1 AUXPORT Control 2 Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved ADC Control 0 ADC Control 1 ADC Control 2 PLL AND CLOCK CONTROL REGISTERS Table 16. PLL and Clock Control 0 Bit 0 2:1 4:3 6:5 7 Value 0 1 00 01 10 11 00 01 10 11 00 01 10 11 0 1 Function Normal operation Power-down INPUT 256 (x44.1 kHz or 48 kHz) INPUT 384 (x44.1 kHz or 48 kHz) INPUT 512 (x44.1 kHz or 48 kHz) INPUT 768 (x44.1 kHz or 48 kHz) XTAL oscillator enabled 256 x fS VCO output 512 x fS VCO output Off MCLKI/XI AUXLRCLK ALRCLK Reserved Disable: ADC idle Enable: ADC active Description PLL power-down MCLKI/XI pin functionality (PLL active), master clock rate setting MCLKO/XO pin, master clock rate setting PLL input Internal MCLK enable Rev. D | Page 18 of 24 Data Sheet AD1974 Table 17. PLL and Clock Control 1 Bit 0 1 2 3 7:4 Value 0 1 0 1 0 1 0 1 0000 Function PLL clock MCLK PLL clock MCLK Enabled Disabled Not locked Locked Reserved Description AUXPORT clock source select ADC clock source select On-chip voltage reference PLL lock indicator (read only) AUXPORT CONTROL REGISTERS Table 18. AUXPORT Control 0 Bit 0 2:1 5:3 7:6 Value 0 1 00 01 10 11 000 001 010 011 100 101 110 111 00 01 10 11 Function Reserved Reserved 32 kHz/44.1 kHz/48 kHz 64 kHz/88.2 kHz/96 kHz 128 kHz/176.4 kHz/192 kHz Reserved 1 0 8 12 16 Reserved Reserved Reserved Stereo (normal) Reserved ADC AUX mode (ADC-, TDM-coupled) Reserved Description Reserved Sample rate AUXDATA delay (AUXBCLK periods) Serial format Table 19. AUXPORT Control 1 Bit 0 2:1 3 4 5 6 7 Value 0 1 00 01 10 11 0 1 0 1 0 1 0 1 0 1 Function Reserved Reserved 64 (two channels) Reserved Reserved Reserved Left low Left high Slave Master Slave Master AUXBCLK pin Internally generated Normal Inverted Description AUXBCLKs per frame AUXLRCLK polarity AUXLRCLK master/slave AUXBCLK master/slave AUXBCLK source AUXBCLK polarity Rev. D | Page 19 of 24 AD1974 Data Sheet Table 20. AUXPORT Control 2 Bit 0 2:1 4:3 5 7:6 Value 0 1 00 01 10 11 00 01 10 11 0 1 00 Function Reserved Reserved Reserved Reserved Reserved Reserved 24 20 Reserved 16 Reserved Reserved Reserved Description Word width ADC CONTROL REGISTERS Table 21. ADC Control 0 Bit 0 1 2 3 4 5 7:6 Value 0 1 0 1 0 1 0 1 0 1 0 1 00 01 10 11 Function Normal Power down Off On Unmute Mute Unmute Mute Unmute Mute Unmute Mute 32 kHz/44.1 kHz/48 kHz 64 kHz/88.2 kHz/96 kHz 128 kHz/176.4 kHz/192 kHz Reserved Description Power-down Function 24 20 Reserved 16 1 0 8 12 16 Reserved Reserved Reserved Description Word width High-pass filter ADC1L mute ADC1R mute ADC2L mute ADC2R mute Output sample rate Table 22. ADC Control 1 Bit 1:0 4:2 Value 00 01 10 11 000 001 010 011 100 101 110 111 SDATA delay (BCLK periods) Rev. D | Page 20 of 24 Data Sheet Bit 6:5 7 AD1974 Value 00 01 10 11 0 1 Function Stereo TDM (daisy chain) ADC AUX mode (TDM-coupled) Reserved Latch in midcycle (normal) Latch in at end of cycle (pipeline) Description Serial format BCLK active edge (TDM_IN) Table 23. ADC Control 2 Bit 0 Value 0 1 0 1 0 1 0 1 00 01 10 11 0 1 0 1 1 2 3 5:4 6 7 Function 50/50 (allows 32-/24-/20-/16-BCLK per channel) Pulse (32-BCLK/channel) Drive out on falling edge (DEF) Drive out on rising edge Left low Left high Slave Master 64 128 256 512 Slave Master ABCLK pin Internally generated Description LRCLK format BCLK polarity LRCLK polarity LRCLK master/slave BCLKs per frame BCLK master/slave BCLK source ADDITIONAL MODES The AD1974 offers several additional modes for board level design enhancements. To reduce the EMI in board level design, serial data can be transmitted without an explicit BCLK. See Figure 15 for an example of an ADC TDM data transmission mode that does not require high speed ABCLK. This configuration is applicable when the AD1974 master clock is generated by the PLL with the ALRCLK as the PLL reference frequency. To relax the requirement for the setup time of the AD1974 in cases of high speed TDM data transmission, the AD1974 can latch in the data using the falling edge of ABCLK. This effectively dedicates the entire BCLK period to the setup time. This mode is useful in cases where the source has a large delay time in the serial data driver. Figure 16 shows this pipeline mode of data transmission. ALRCLK 32 BITS INTERNAL ABCLK ASDATA2 ALRCLK 06614-059 INTERNAL ABCLK ASDATA2 Figure 15. Serial ADC Data Transmission in TDM Format Without ABCLK (Applicable Only If PLL Locks to ALRCLK) Rev. D | Page 21 of 24 AD1974 Data Sheet ALRCLK ABCLK ASDATA1 06614-060 DATA MUST BE VALID AT THIS BCLK EDGE MSB Figure 16. I2S Pipeline Mode in ADC Serial Data Transmission (Applicable in Stereo and TDM Useful for High Frequency TDM Transmission) Rev. D | Page 22 of 24 Data Sheet AD1974 APPLICATION CIRCUITS Typical applications circuits are shown in Figure 17 and Figure 18. Figure 17 shows a typical ADC input filter circuit. Recommended loop filters for LR clock and master clock as the PLL reference are shown in Figure 18. 120pF 100pF 5.76k 2 3 + - OP275 AVDD2 4.7F 237 + 120pF 1nF NP0 5 - + 5.6nF 390pF 7 4.7F 237 1nF NP0 + ADCxP 562 AVDD2 Figure 18. Recommended Loop Filters for LRCLK or MCLK PLL Reference ADCxN 100pF 5.76k MCLK 2.2nF 3.32k + OP275 LF 39nF 1 5.76k 6 LRCLK LF 5.76k 06614-027 600Z 06614-023 AUDIO INPUT Figure 17. Typical ADC Input Filter Circuit Rev. D | Page 23 of 24 AD1974 Data Sheet OUTLINE DIMENSIONS 9.20 9.00 SQ 8.80 1.60 MAX 37 48 36 1 PIN 1 7.20 7.00 SQ 6.80 TOP VIEW 1.45 1.40 1.35 0.15 0.05 0.20 0.09 7 3.5 0 0.08 COPLANARITY SEATING PLANE VIEW A (PINS DOWN) 25 12 13 VIEW A 0.50 BSC LEAD PITCH 24 0.27 0.22 0.17 ROTATED 90 CCW COMPLIANT TO JEDEC STANDARDS MS-026-BBC 051706-A 0.75 0.60 0.45 Figure 19. 48-Lead Low Profile Quad Flat Package [LQFP] (ST-48) Dimensions shown in millimeters ORDERING GUIDE Model1, 2, 3 AD1974YSTZ AD1974YSTZ-RL AD1974WBSTZ AD1974WBSTZ-RL EVAL-AD1974AZ Temperature Range -40C to +105C -40C to +105C -40C to +105C -40C to +105C Package Description 48-Lead LQFP 48-Lead LQFP, 13" Tape and Reel 48-Lead LQFP 48-Lead LQFP, 13" Tape and Reel Evaluation Board Package Option ST-48 ST-48 ST-48 ST-48 1 Z = RoHS Compliant Part. W = Qualified for Automotive Applications. 3 SPI control port. 2 AUTOMOTIVE PRODUCTS The AD1974W models are available with controlled manufacturing to support the quality and reliability requirements of automotive applications. Note that these automotive models may have specifications that differ from the commercial models; therefore, designers should review the Specifications section of this data sheet carefully. Only the automotive grade products shown are available for use in automotive applications. Contact your local Analog Devices account representative for specific product ordering information and to obtain the specific Automotive Reliability reports for these models. (c)2007-2013 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D06614-0-3/13(D) Rev. D | Page 24 of 24