Notice for TAIYO YUDEN products Please read this notice before using the TAIYO YUDEN products. REMINDERS Product information in this catalog is as of October 2013. All of the contents specified herein are subject to change without notice due to technical improvements, etc. Therefore, please check for the latest information carefully before practical application or usage of the Products. Please note that TAIYO YUDEN CO., LTD. shall not be responsible for any defects in products or equipment incorporating such products, which are caused under the conditions other than those specified in this catalog or individual specification. Please contact TAIYO YUDEN CO., LTD. for further details of product specifications as the individual specification is available. Please conduct validation and verification of products in actual condition of mounting and operating environment before commercial shipment of the equipment. All electronic components or functional modules listed in this catalog are developed, designed and intended for use in general electronics equipment.(for AV, office automation, household, office supply, information service, telecommunications, (such as mobile phone or PC) etc.). Before incorporating the components or devices into any equipment in the field such as transportation,( automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network (telephone exchange, base station) etc. which may have direct influence to harm or injure a human body, please contact TAIYO YUDEN CO., LTD. for more detail in advance. Do not incorporate the products into any equipment in fields such as aerospace, aviation, nuclear control, submarine system, military, etc. where higher safety and reliability are especially required. In addition, even electronic components or functional modules that are used for the general electronic equipment, if the equipment or the electric circuit require high safety or reliability function or performances, a sufficient reliability evaluation check for safety shall be performed before commercial shipment and moreover, due consideration to install a protective circuit is strongly recommended at customer's design stage. The contents of this catalog are applicable to the products which are purchased from our sales offices or distributors (so called TAIYO YUDEN s official sales channel ). It is only applicable to the products purchased from any of TAIYO YUDEN s official sales channel. Please note that TAIYO YUDEN CO., LTD. shall have no responsibility for any controversies or disputes that may occur in connection with a third party's intellectual property rights and other related rights arising from your usage of products in this catalog. TAIYO YUDEN CO., LTD. grants no license for such rights. Caution for export Certain items in this catalog may require specific procedures for export according to Foreign Exchange and Foreign Trade Control Law of Japan, U.S. Export Administration Regulations , and other applicable regulations. Should you have any question or inquiry on this matter, please contact our sales staff. 14 MULTILAYER CHIP BEAD INDUCTORS(BK SERIES) MULTILAYER CHIP BEAD INDUCTORS (BK SERIES) PARTS NUMBER B K 1 6 0 8 H S 1 2 1 T Multilayer chip bead inductor FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS Code Typeinch 0402 0603 1005 1608 2125 040201005 06030201 10050402 16080603 21250805 Blank space Nominal impedance Code example 150 101 102 Series name DimensionsLxW Material Code HW HS HR HM LM LL TS TM REFLOW *Operating Temp. : -55+125 Series name Code BK BKH WAVE Except for BK0402, BK0603, BK1005, BKH1005 Dimensions LxWmm 0.4x0.2 0.6x0.3 1.0x0.5 1.6x0.8 2.0x1.25 Characteristics Code Packaging Code T 15 100 1000 Characteristics Standard Packaging Taping Internal code Code Material Nominal impedance Internal code Standard Refer to impedance curves for material differences STANDARD EXTERNAL DIMENSIONS / STANDARD QUANTITY Type BK 0402 01005 BK 0603 BKH0603 0201 BK 1005 BKH1005 0402 BK 1608 0603 BK 2125 0805 Standard quantity [pcs] Paper tape Embossed tape L W T e 0.400.02 0.0160.001 0.200.02 0.0080.001 0.200.02 0.0080.001 0.100.04/0.03 0.0040.002/0.001 20000 0.600.03 0.0240.001 0.300.03 0.0120.001 0.300.03 0.0120.001 0.150.05 0.0060.002 15000 1.000.05 0.0390.002 0.500.05 0.0200.002 0.500.05 0.0200.002 0.250.10 0.0100.004 10000 1.60.15 0.0630.006 2.00.3/0.1 0.0790.012/0.004 2.00.3/0.1 0.0790.012/0.004 0.80.15 0.0310.006 1.250.2 0.0490.008 1.250.2 0.0490.008 0.80.15 0.0310.006 0.850.2 0.0330.008 1.250.2 0.0490.008 0.30.2 0.0120.008 0.50.3 0.0200.012 0.50.3 0.0200.012 4000 4000 2000 Unitmminch This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please checki_mlci_BK_e-E02R01 our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . 92 14 PARTS NUMBER BK 0402 Parts number BK 0402HS100-T BK 0402HS700-T BK 0402HS121-T BK 0402HM100-T BK 0402HM750-T BK 0402HM121-T BK 0402HM151-T BK 0402HM181-T BK 0402LL220-T EHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Nominal impedance 10 70 120 10 75 120 150 180 22 Impedance tolerance 5 25 25 5 25 25 25 25 25 Measuring frequency MHz 100 100 100 100 100 100 100 100 100 DC Resistance max. 0.10 0.37 0.53 0.07 0.45 0.60 0.65 0.75 0.70 Rated current mAmax. 540 280 240 750 260 220 200 200 150 Thickness mm 0.20 0.02 0.20 0.02 0.20 0.02 0.20 0.02 0.20 0.02 0.20 0.02 0.20 0.02 0.20 0.02 0.20 0.02 Measuring frequency MHz 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 DC Resistance max. 0.065 0.070 0.40 0.45 0.65 1.20 0.25 0.40 0.80 1.05 1.20 0.25 0.45 0.55 0.70 1.00 1.30 1.50 0.18 0.23 0.32 0.75 0.18 0.23 0.38 0.85 1.50 2.50 3.20 Rated current mAmax. 500 500 200 200 200 150 200 200 200 100 100 200 200 150 150 100 100 100 500 450 400 270 450 400 300 250 160 130 115 Thickness mm 0.30 0.03 0.30 0.03 0.30 0.03 0.30 0.03 0.30 0.03 0.30 0.03 0.30 0.03 0.30 0.03 0.30 0.03 0.30 0.03 0.30 0.03 0.30 0.03 0.30 0.03 0.30 0.03 0.30 0.03 0.30 0.03 0.30 0.03 0.30 0.03 0.30 0.03 0.30 0.03 0.30 0.03 0.30 0.03 0.30 0.03 0.30 0.03 0.30 0.03 0.30 0.03 0.30 0.03 0.30 0.03 0.30 0.03 Measuring frequency MHz 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 DC Resistance max. 0.17 0.24 0.31 0.50 0.60 0.03 0.06 0.10 0.10 0.20 0.30 0.45 0.55 0.58 0.60 0.18 0.18 0.30 0.45 0.50 0.70 0.11 0.18 0.25 0.33 0.31 0.45 0.50 0.70 0.90 0.85 1.25 1.50 2.00 Rated current mAmax. 500 450 400 350 300 1,000 700 700 700 500 400 350 300 300 300 350 300 300 250 250 150 500 400 400 350 400 350 300 250 120 300 250 200 200 Thickness mm 0.50 0.05 0.50 0.05 0.50 0.05 0.50 0.05 0.50 0.05 0.50 0.05 0.50 0.05 0.50 0.05 0.50 0.05 0.50 0.05 0.50 0.05 0.50 0.05 0.50 0.05 0.50 0.05 0.50 0.05 0.50 0.05 0.50 0.05 0.50 0.05 0.50 0.05 0.50 0.05 0.50 0.05 0.50 0.05 0.50 0.05 0.50 0.05 0.50 0.05 0.50 0.05 0.50 0.05 0.50 0.05 0.50 0.05 0.50 0.05 0.50 0.05 0.50 0.05 0.50 0.05 0.50 0.05 BK 0603 EHS BK 0603HS220-T BK 0603HS330-T BK 0603HS800-T BK 0603HS121-T BK 0603HS241-T BK 0603HS601-T BK 0603HM600-T BK 0603HM121-T BK 0603HM241-T BK 0603HM471-T BK 0603HM601-T BK 0603LL100-T BK 0603LL220-T BK 0603LL330-T BK 0603LL470-T BK 0603LL560-T BK 0603LL800-T BK 0603LL121-T BK 0603TS800-T BK 0603TS121-T BK 0603TS241-T BK 0603TS601-T BK 0603TM800-T BK 0603TM121-T BK 0603TM241-T BK 0603TM601-T BKH0603LM601-T BKH0603LM102-T BKH0603LM152-T RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Nominal impedance 22 33 80 120 240 600 60 120 240 470 600 10 22 33 47 56 80 120 80 120 240 600 80 120 240 600 600 1000 1500 Impedance tolerance 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 BK 1005 Parts number EHS BK 1005HW680-T BK 1005HW121-T BK 1005HW241-T BK 1005HW431-T BK 1005HW601-T BK 1005HS100-T BK 1005HS330-T BK 1005HS680-T BK 1005HS800-T BK 1005HS121-T BK 1005HS241-T BK 1005HS431-T BK 1005HS601-T BK 1005HS102-T BK 1005HR601-T BK 1005HM750-T BK 1005HM121-T BK 1005HM241-T BK 1005HM471-T BK 1005HM601-T BK 1005HM102-T BK 1005LL100-T BK 1005LL220-T BK 1005LL330-T BK 1005LL470-T BK 1005LL680-T BK 1005LL121-T BK 1005LL181-T BK 1005LL241-T BK 1005LM182-T BKH1005LM601-T BKH1005LM102-T BKH1005LM152-T BKH1005LM182-T RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Nominal impedance 68 120 240 430 600 10 33 68 80 120 240 430 600 1000 600 75 120 240 470 600 1000 10 22 33 47 68 120 180 240 1800 600 1000 1500 1800 Impedance tolerance 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS Parts number i_mlci_BK_e-E02R01 This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . 14 93 PARTS NUMBER BK 1608 Parts number FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS BK 1608HW121-T BK 1608HW241-T BK 1608HW431-T BK 1608HW601-T BK 1608HS220-T BK 1608HS330-T BK 1608HS470-T BK 1608HS600-T BK 1608HS800-T BK 1608HS121-T BK 1608HS241-T BK 1608HS601-T BK 1608HS102-T BK 1608HM121-T BK 1608HM241-T BK 1608HM471-T BK 1608HM601-T BK 1608HM102-T BK 1608LL300-T BK 1608LL470-T BK 1608LL560-T BK 1608LL680-T BK 1608LL121-T BK 1608LL181-T BK 1608LL241-T BK 1608LL331-T BK 1608LL431-T BK 1608LL511-T BK 1608LL681-T BK 1608LM751-T BK 1608LM152-T BK 1608LM182-T BK 1608LM252-T BK 1608TS431-T BK 1608TS601-T BK 1608TS102-T EHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Nominal impedance 120 240 430 600 22 33 47 60 80 120 240 600 1000 120 240 470 600 1000 30 47 56 68 120 180 240 330 430 510 680 750 1500 1800 2500 430 600 1000 Impedance tolerance 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 Measuring frequency MHz 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 DC Resistance max. 0.15 0.25 0.30 0.40 0.05 0.08 0.10 0.10 0.10 0.18 0.25 0.45 0.60 0.20 0.35 0.45 0.60 0.70 0.20 0.30 0.30 0.35 0.50 0.65 0.80 0.85 0.85 0.90 1.00 0.60 0.75 0.85 1.10 0.2130 0.2730 0.3030 Rated current mAmax. 600 450 400 300 1,500 1,200 900 800 600 500 400 350 300 350 300 250 250 200 500 400 400 300 300 250 250 200 200 200 150 300 250 200 200 400 350 300 Thickness mm 0.80 0.15 0.80 0.15 0.80 0.15 0.80 0.15 0.80 0.15 0.80 0.15 0.80 0.15 0.80 0.15 0.80 0.15 0.80 0.15 0.80 0.15 0.80 0.15 0.80 0.15 0.80 0.15 0.80 0.15 0.80 0.15 0.80 0.15 0.80 0.15 0.80 0.15 0.80 0.15 0.80 0.15 0.80 0.15 0.80 0.15 0.80 0.15 0.80 0.15 0.80 0.15 0.80 0.15 0.80 0.15 0.80 0.15 0.80 0.15 0.80 0.15 0.80 0.15 0.80 0.15 0.80 0.15 0.80 0.15 0.80 0.15 Measuring frequency MHz 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 DC Resistance max. 0.05 0.05 0.05 0.05 0.10 0.10 0.15 0.20 0.25 0.30 0.40 0.15 0.20 0.25 0.25 0.35 0.20 0.30 0.35 0.30 0.35 0.45 0.75 Rated current mAmax. 1,200 1,200 1,200 1,000 1,000 900 800 600 500 500 300 800 600 500 500 400 600 400 300 400 400 300 200 Thickness mm 0.85 0.2 0.85 0.2 0.85 0.2 0.85 0.2 0.85 0.2 0.85 0.2 0.85 0.2 0.85 0.2 0.85 0.2 0.85 0.2 0.85 0.2 0.85 0.2 0.85 0.2 0.85 0.2 0.85 0.2 0.85 0.2 0.85 0.2 0.85 0.2 0.85 0.2 0.85 0.2 0.85 0.2 1.25 0.2 1.25 0.2 BK 2125 Parts number BK 2125HS150-T BK 2125HS220-T BK 2125HS330-T BK 2125HS470-T BK 2125HS750-T BK 2125HS101-T BK 2125HS121-T BK 2125HS241-T BK 2125HS431-T BK 2125HS601-T BK 2125HS102-T BK 2125HM121-T BK 2125HM241-T BK 2125HM471-T BK 2125HM601-T BK 2125HM102-T BK 2125LL560-T BK 2125LL121-T BK 2125LL241-T BK 2125LM751-T BK 2125LM152-T BK 2125LM182-T BK 2125LM252-T EHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Nominal impedance 15 22 33 47 75 100 120 240 430 600 1000 120 240 470 600 1000 56 120 240 750 1500 1800 2500 Impedance tolerance 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 25 i_mlci_BK_e-E02R01 This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . 94 14 ELECTRICAL CHARACTERISTICS BK0402 BK0402 HS700 80 200 200 25 60 40 10 100 1000 Frequency [MHz] 0 10000 10 100 1000 Frequency [MHz] 0 10000 15 10 250 200 200 150 10 100 1000 Frequency [MHz] BK0402 HM151 350 10 100 1000 Frequency [MHz] 10 100 1000 Frequency [MHz] 10000 BK0402 HM181 450 300 350 150 100 0 10000 1 400 250 200 150 100 50 50 0 10000 1 10 100 1000 Frequency [MHz] 200 150 50 0 1 10000 250 100 50 300 10 100 1000 Frequency [MHz] 0 10000 1 10 100 1000 Frequency [MHz] 10000 BK0603 BK0603 HS220 250 Impedance 150 100 100 80 80 200 60 150 60 40 20 50 0 1 10 100 1000 Frequency [MHz] 0 10000 0 10000 X 1 10 100 1000 FrequencyMHz 10000 BK0603 HS601 1000 200 800 200 600 150 Impedance 250 R Z 50 200 100 1000 1 10000 500 200 400 Impedance 250 150 100 50 10 100 1000 BK0603 LL100 250 1000 0 10000 R 200 X 1 BK0603 LL220 Z 50 100 Z 10 100 1000 FrequencyMHz 10000 0 400 1 10 100 1000 FrequencyMHz 1 10 100 1000 10000 BK0603 HM601 1 600 Z 400 R 200 10 100 1000 FrequencyMHz 0 10000 BK0603 LL330 BK0603 LL470 500 400 300 200 Z 300 Z 200 X X 10000 0 R 100 R 1 R 100 50 X 10000 800 400 150 1000 1000 Z 500 Impedance Impedance 100 10000 BK0603 HM471 600 0 10000 200 150 10 100 1000 FrequencyMHz 200 10 100 1000 FrequencyMHz 100 50 X 800 250 200 1 1000 Z 300 0 10000 100 BK0603 HM241 100 1 10 Impedance 10 R 10 100 Z X 1 0 400 1 250 Impedance[ ] 100 R Z 50 X 10 100 1000 Frequency [MHz] 150 Impedance 100 Z R 20 1 40 250 Impedance Impedance 200 BK0603 HS330 100 Impedance BK0402 LL220 FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS Impedance 250 1 BK0402 HM121 300 1 20 50 1 BK0402 HM750 100 100 BK0402 HM100 5 300 0 50 1 Impedance 0 100 150 Impedance 150 Impedance 30 Impedance 250 20 Impedance BK0402 HS121 250 Impedance Impedance BK0402 HS100 100 1 10 100 1000 FrequencyMHz 10000 0 1 10 100 1000 FrequencyMHz 10000 This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . 14 95 ELECTRICAL CHARACTERISTICS BK0603 LL560 500 BK0603 LL800 1000 BK0603 LL121 1000 BK0603 TS800 200 Z 1 0 10000 BK0603 TS121 250 Impedance BK0603 TS241 1 10 100 1000 FrequencyMHz 200 BK0603 TM121 1 10 100 1000 FrequencyMHz 0 BK0603 TM241 Impedance 100 200 50 100 1 10 100 1000 FrequencyMHz 0 10000 10 100 1000 FrequencyMHz 0 10000 BK0603 TM601 1 10 100 1000 FrequencyMHz 10000 X 1 10 100 1000 FrequencyMHz 10000 BK0603 LM601 2000 1500 400 0 R Z 50 1000 200 10000 BK0603 TM800 100 1 600 10 100 1000 FrequencyMHz 800 300 X 1 200 1000 400 150 0 10000 150 200 10000 R 50 BK0603 TS601 400 500 200 10 100 1000 FrequencyMHz 600 Z 1 1000 300 0 10000 100 800 100 250 Impedance 0 10000 Impedance Impedance 50 1 500 10 100 1000 FrequencyMHz 0 10000 1 10 100 1000 FrequencyMHz 10000 BK1005 1000 500 1000 1 10 100 1000 FrequencyMHz 0 10000 1 10 100 1000 FrequencyMHz Z R 100 400 Z 1 10000 R Z 20 100 Z 50 10 100 R 1 10 100 1000 FrequencyMHz 1000 10000 0 1 10 100 1000 FrequencyMHz 10000 60 40 10000 0 Z R 1 X 10 100 1000 FrequencyMHz 10000 250 200 200 150 150 100 100 Z 50 R 50 X X FrequencyMHz 10 100 1000 FrequencyMHz BK1005 HS100 20 BK1005 HS800 250 150 X 1 Z 400 10000 Impedance 40 1 80 600 0 200 60 0 10 100 1000 FrequencyMHz X BK1005 HS680 250 Impedance Impedance 1 100 200 BK1005 HS330 80 10000 BK1005 HW601 X 10 100 1000 FrequencyMHz 100 R 200 0 0 800 600 100 X 10 100 1000 FrequencyMHz 1000 X 0 1 150 50 R BK1005 HW431 Impedance Impedance 200 Z 10000 800 300 100 0 1000 400 150 50 500 BK1005 HW241 500 1500 200 Impedance BK1005 HW121 250 200 2000 Impedance 1500 BK1005 HW680 250 Impedance Impedance 3000 2500 2000 0 BKH0603 LM152 Impedance BKH0603 LM102 2500 Impedance FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS 100 0 1 400 150 0 200 X 10 100 1000 FrequencyMHz 500 200 Impedance 200 X 10 100 1000 FrequencyMHz 400 Impedance 0 R Z Impedance 100 Z 400 150 600 Impedance 200 800 600 Impedance 800 R 300 Impedance Impedance 400 10000 0 0 1 10 100 1000 FrequencyMHz 10000 This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . 96 14 ELECTRICAL CHARACTERISTICS BK1005 HS431 1000 BK1005 HS102 2000 Impedance Impedance 800 600 400 Z 1000 Z 200 0 1 R X 10 100 1000 FrequencyMHz BK1005 HR601 0 10000 BK1005 HM750 1000 200 800 Impedance 600 100 50 0 10000 10 10000 400 Z 150 300 R 200 100 100 50 0 0 1 X 10 100 1000 FrequencyMHz 0 10000 1 BK1005 HM102 100 1000 BK1005 LL100 2000 250 200 150 1000 100 50 0 1 BK1005 LL220 500 500 200 400 400 150 300 300 100 200 200 50 100 100 0 0 0 10 100 1000 10000 1 10 100 100 1000 0 10000 1 10 100 1000 10000 BK1005 LL470 BK1005 LL330 250 1 10 1000 BK1005 LL680 500 400 300 200 100 0 1 10000 10 100 1000 1 10000 10 100 1000 10000 BK1005 LM182 2500 2000 FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS 400 R X 10 100 1000 FrequencyMHz 500 200 150 200 BK1005 HM121 250 1 1500 Z 1000 R 500 X 0 1 BKH1005 LM601 BK1005 LM102 2000 1500 800 600 1000 400 Z 500 R 200 0 1 10 100 Frequency [MHz] 1000 10000 1 10 100 1500 R 1000 X 1000 10000 10000 2500 Z 2000 500 X 0 1000 3000 2500 1000 100 BKH1005 LM182 3000 Impedance[ ] Impedance BKH1005 LM152 2500 1200 Impedance[ ] 1400 10 0 Z 2000 1500 R 1000 500 X 0 This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . 14 97 ELECTRICAL CHARACTERISTICS BK1608 FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS BK1608 LL300 BK1608 LL470 500 500 250 250 0 0 1 BK1608 LL560 BK1608 LL680 500 1500 250 250 750 0 1 10 100 1000 10000 100 1000 10000 1 10 100 1000 10000 BK1608 LL121 500 0 10 0 1 10 100 1000 10000 1 10 100 1000 This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . 98 14 ELECTRICAL CHARACTERISTICS 4000 2000 FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS BK2125 This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . 14 99 ELECTRICAL CHARACTERISTICS 1000 Z 500 R X 0 1 10 100 1000 1000 Z R 500 FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS 0 X 1 10 100 1000 This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . 100 14 Multilayer chip inductors Multilayer chip inductors for high frequency, Multilayer chip bead inductors Multilayer common mode choke coilsMC series F type PACKAGING Minimum Quantity Tape & Reel Packaging Type CK16080603 CK21250805 CKS21250805 CKP16080603 CKP20120805 CKP20160806 CKP25201008 NM20120805 NM25201008 LK10050402 LK16080603 LK21250805 HK040201005 HK06030201 HK10050402 HK16080603 HK21250805 HKQ040201005 HKQ0603W0201 HKQ0603C0201 HKQ0603S0201 HKQ0603U0201 AQ1050402 BK040201005 BK06030201 BK10050402 BKH06030201 BKH10050402 BK16080603 BK21250805 BK20100804 BK32161206 BKP06030201 BKP10050402 BKP16080603 BKP21250805 MCF0605(0202) MCF0806(0302) MCF1210(0504) MCF2010(0804) Thickness mminch 0.8 0.031 0.850.033 1.250.049 0.850.033 1.250.049 0.8 0.031 0.9 0.035 0.9 0.035 0.7 0.028 0.9 0.035 1.1 0.043 0.9 0.035 0.9 0.035 1.1 0.043 0.5 0.020 0.8 0.031 0.850.033 1.250.049 0.2 0.008 0.3 0.012 0.5 0.020 0.8 0.031 0.850.033 1.0 0.039 0.2 0.008 0.3 0.012 0.3 0.012 0.3 0.012 0.3 0.012 0.5 0.020 0.2 0.008 0.3 0.012 0.5 0.020 0.3 0.012 0.5 0.020 0.8 0.031 0.850.033 1.250.049 0.450.018 0.8 0.031 0.3 0.012 0.5 0.020 0.8 0.031 0.850.033 0.3 0.012 0.4 0.016 0.550.022 0.450.018 Standard Quantity pcs Paper Tape Embossed Tape 4000 4000 2000 4000 2000 4000 3000 3000 3000 3000 2000 3000 3000 2000 10000 4000 4000 2000 20000 15000 10000 4000 4000 3000 20000 40000 15000 15000 15000 15000 10000 20000 15000 10000 15000 10000 4000 4000 2000 4000 4000 15000 10000 4000 4000 15000 10000 5000 4000 This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_pack_e-E02R01 Taping material Card board carrier tape Top tape Base tape Sprocket hole Bottom tape Chip cavity CK CKP CK CKS LK LK LK HK HK HK HK HKQ HKQ AQ 1608 1608 2125 2125 1005 1608 2125 0402 0603 1005 1608 0402 0603 105 BK BK BK BK BK BK BKP BKP BKP BKP BKH BKH MCF 0402 0603 1005 1608 2125 2010 0603 1005 1608 2125 0603 1005 0605 CK CKS CKP CKP CKP NM NM LK HKQ HK 2125 2125 2012 2016 2520 2012 2520 2125 0402 2125 BK BK MCF MCF MCF 2125 3216 0806 1210 2010 Chip Filled Chip Embossed Tape Top tape Sprocket hole Base tape Chip cavity Chip Filled Chip Taping Dimensions Paper tape (8mm wide) This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_pack_e-E02R01 Type Thickness mminch CK16080603 0.8 0.031 CK21250805 0.850.033 CKS21250805 0.850.033 CKP16080603 0.8 0.031 LK10050402 0.5 0.020 LK16080603 0.8 0.031 LK21250805 0.850.033 HK040201005 0.2 0.008 HK06030201 0.3 0.012 HK10050402 0.5 0.020 HK16080603 0.8 0.031 HKQ040201005 0.2 0.008 HKQ0603W0201 0.3 0.012 HKQ0603C0201 0.3 0.012 HKQ0603S0201 0.3 0.012 HKQ0603U0201 0.3 0.012 AQ1050402 0.5 0.020 BK040201005 0.2 0.008 BK06030201 0.3 0.012 BK10050402 0.5 0.020 BK16080603 0.8 0.031 BK21250805 0.850.033 BK20100804 0.450.018 BKP06030201 0.3 0.012 BKP10050402 0.5 0.020 BKP16080603 0.8 0.031 BKP21250805 0.850.033 BKH06030201 0.3 0.012 BKH10050402 0.5 0.020 MCF0605(0202) 0.3 0.012 Chip cavity 1.00.2 1.80.2 0.0390.008 0.0710.008 1.50.2 2.30.2 0.0590.008 0.0910.008 1.50.2 2.30.2 0.0590.008 0.0910.008 1.00.2 1.80.2 0.0390.008 0.0710.008 0.650.1 1.150.1 0.0260.004 0.0450.004 1.00.2 1.80.2 0.0390.008 0.0710.008 1.50.2 2.30.2 0.0590.008 0.0910.008 0.250.04 0.450.04 0.0100.002 0.0180.002 0.400.06 0.700.06 0.0160.002 0.0280.002 0.650.1 1.150.1 0.0260.004 0.0450.004 1.00.2 1.80.2 0.0390.008 0.0710.008 0.250.04 0.450.04 0.0100.002 0.0180.002 0.400.06 0.700.06 0.0160.002 0.0280.002 0.400.06 0.700.06 0.0160.002 0.0280.002 0.400.06 0.700.06 0.0160.002 0.0280.002 0.400.06 0.700.06 0.0160.002 0.0280.002 0.750.1 1.150.1 0.0300.004 0.0450.004 0.250.04 0.450.04 0.0100.002 0.0180.002 0.400.06 0.700.06 0.0160.002 0.0280.002 0.650.1 1.150.1 0.0260.004 0.0450.004 1.00.2 1.80.2 0.0390.008 0.0710.008 1.50.2 2.30.2 0.0590.008 0.0910.008 1.20.1 2.170.1 0.0470.004 0.0850.004 0.400.06 0.700.06 0.0160.002 0.0280.002 0.650.1 1.150.1 0.0260.004 0.0450.004 1.00.2 1.80.2 0.0390.008 0.0710.008 1.50.2 2.30.2 0.0590.008 0.0910.008 0.400.06 0.700.06 0.0160.002 0.0280.002 0.650.1 1.150.1 0.0260.004 0.0450.004 0.620.03 0.770.03 0.0240.001 0.0300.001 Insertion Pitch 4.00.1 0.1570.004 4.00.1 0.1570.004 4.00.1 0.1570.004 4.00.1 0.1570.004 2.00.05 0.0790.002 4.00.1 0.1570.004 4.00.1 0.1570.004 2.00.05 0.0790.002 2.00.05 0.0790.002 2.00.05 0.0790.002 4.00.1 0.1570.004 2.00.05 0.0790.002 2.00.05 0.0790.002 2.00.05 0.0790.002 2.00.05 0.0790.002 2.00.05 0.0790.002 2.00.05 0.0790.002 2.00.05 0.0790.002 2.00.05 0.0790.002 2.00.05 0.0790.002 4.00.1 0.1570.004 4.00.1 0.1570.004 4.00.1 0.1570.004 2.00.05 0.0790.002 2.00.05 0.0790.002 4.00.1 0.1570.004 4.00.1 0.1570.004 2.00.05 0.0790.002 2.00.05 0.0790.002 2.00.05 0.0790.002 Tape Thickness 1.1max 0.043max 1.1max 0.043max 1.1max 0.043max 1.1max 0.043max 0.8max 0.031max 1.1max 0.043max 1.1max 0.043max 0.36max 0.014max 0.45max 0.018max 0.8max 0.031max 1.1max 0.043max 0.36max 0.014max 0.45max 0.018max 0.45max 0.018max 0.45max 0.018max 0.45max 0.018max 0.8max 0.031max 0.36max 0.014max 0.45max 0.018max 0.8max 0.031max 1.1max 0.043max 1.1max 0.043max 0.8max 0.031max 0.45max 0.018max 0.8max 0.031max 1.1max 0.043max 1.1max 0.043max 0.45max 0.018max 0.8max 0.031max 0.45max 0.018max Unit : mminch This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_pack_e-E02R01 Embossed Tape (8mm wide) Type Thickness mminch CK21250805 1.250.049 CKS21250805 1.250.049 CKP20120805 0.9 0.035 CKP20160806 0.9 0.035 Chip cavity 1.50.2 2.30.2 0.0590.008 0.0910.008 1.50.2 2.30.2 0.0590.008 0.0910.008 1.550.2 2.30.2 0.0610.008 0.0910.008 1.80.1 2.20.1 0.0710.004 0.0870.004 Insertion Pitch 4.00.1 0.1570.004 4.00.1 0.1570.004 4.00.1 0.1570.004 4.00.1 0.1570.004 2.30.1 0.0910.004 2.80.1 0.1100.004 4.00.1 0.1570.004 1.550.2 0.0610.008 2.30.2 0.0910.008 4.00.1 0.1570.004 2.30.1 0.0910.004 2.80.1 0.1100.004 4.00.1 0.1570.004 1.50.2 0.0590.008 2.30.2 0.0910.008 4.00.1 0.1570.004 1.50.2 0.0590.008 2.30.2 0.0910.008 4.00.1 0.1570.004 1.50.2 0.0590.008 1.90.1 0.0750.004 0.750.05 0.0300.002 1.150.05 0.0450.002 1.10.1 0.0430.004 2.30.2 0.0910.008 3.50.1 0.1380.004 0.950.05 0.0370.002 1.400.05 0.0550.002 2.30.1 0.0910.004 4.00.1 0.1570.004 4.00.1 0.1570.004 2.00.05 0.0790.002 4.00.1 0.1570.004 4.00.1 0.1570.004 0.7 0.028 CKP25201008 0.9 0.035 1.1 0.043 NM20120805 0.9 0.035 0.9 0.035 NM25201008 1.1 0.043 LK21250805 1.250.049 0.850.033 HK21250805 1.0 0.039 BK21250805 1.250.049 BK32161206 0.80.031 MCF0806(0302) 0.4 0.016 MCF1210(0504) 0.550.022 MCF2010(0804) 0.450.018 Tape Thickness K T 2.0 0.3 0.079 0.012 2.0 0.3 0.079 0.012 1.3 0.3 0.051 0.012 1.3 0.25 0.051 0.01 1.4 0.055 1.4 0.3 0.055 0.012 1.7 0.067 1.3 0.3 0.051 0.012 1.4 0.055 0.3 0.012 1.7 0.067 2.0 0.3 0.079 0.012 1.5 0.059 0.3 0.012 2.0 0.079 2.0 0.3 0.079 0.012 1.4 0.3 0.055 0.012 0.55 0.3 0.022 0.012 0.65 0.3 0.026 0.012 0.85 0.3 0.033 0.012 Unit : mminch Embossed Tape (4mm wide) Type HKQ0402(01005) Thickness mminch 0.2 0.008 Chip cavity 0.23 0.43 Insertion Pitch 1.00.02 Tape Thickness K T 0.5max. 0.25max. Unit : mm This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_pack_e-E02R01 LEADER AND BLANK PORTION Blank portion Chip cavity Blank portion Leader 100mm or more (3.94inches or more) 160mm or more (6.3inches or more) Direction of tape feed 400mm or more (15.7inches or more) Reel Size t E C R B D A W A 1782.0 B 50 or more C 13.00.2 4mm width tape 8mm width tape t 1.5max. 2.5max. W 51.0 101.5 D 21.00.8 E 2.00.5 R 1.0 (Unit : mm) Top tape strength The top tape requires a peel-off force of 0.10.7N in the direction of the arrow as illustrated below. Pull direction 015 Top tape Base tape This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_pack_e-E02R01 Multilayer chip inductors Multilayer chip inductors for high frequency, Multilayer chip bead inductors Multilayer common mode choke coilsMC series F type RELIABILITY DATA 1. Operating Temperature Range BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY Specified Value 55125 BK2010 BK3216 BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 HK0402/HKQ0402 HK0603 HK1005 HK1608 HK2125 HKQ0603W/HKQ0603C/HKQ0603S/ HKQ0603U/ AQ105 5585 4085 4085 55125 4085 55125 This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E02R01 2. Storage Temperature Range BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY Specified Value 55125 BK2010 BK3216 BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 HK0402/HKQ0402 HK0603 HK1005 HK1608 HK2125 HKQ0603W/HKQ0603C/HKQ0603S/ HKQ0603U/ AQ105 5585 4085 4085 55125 4085 55125 This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E02R01 3. Rated Current BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY BK2010 BK3216 150750mA DC 100500mA DC 1201000mA DC 115160mA DC 200300mA DC 1501500mA DC 2001200mA DC 100mA DC 100200mA DC 0.81.8A DC 0.82.4A DC 1.03.0A DC 1.54.0A DC 0.05A DC 0.10.13A DC 0.1A DC 0.1A DC 5060mA DC 60500mA DC 110280mA DC 0.350.9A DC 0.71.2A DC 0.91.6A DC 1.11.8A DC 1.01.2A DC 0.91.2A DC 2025mA DC 1150mA DC 5300mA DC 160380mA DC 60470mA DC 110300mA DC (-55+125 200900mA DC (-55+85) 150300mA DC 300mA DC 90500mA DC 100850mA DC 160850mA DC 130600mA DC 190900mA DC 280710mA DC BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 Specified Value CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 HK0402 HK0603 HK1005 HK1608 HK2125 HKQ0402 HKQ0603W HKQ0603C HKQ0603S HKQ0603U AQ105 Definition of rated current In the CK, CKS and BK Series, the rated current is the value of current at which the temperature of the element is increased within 20. In the BK Series P type and CK Series P type, NM Series the rated current is the value of current at which the temperature of the element is increased within 40. In the LK, HK, HKQ, and AQ Series, the rated current is either the DC value at which the internal L value is decreased within 5% with the application of DC bias, or the value of current at which the temperature of the element is increased within 20. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E02R01 4. Impedance BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY Specified Value Test Methods and Remarks BK2010 BK3216 10180 5(10), 25%(Other) 10600 25% 101800 25% 6001500 25% 6001800 25% 222500 25% 152500 25% 51000 25% 601000 25% 10120 5(10), 25%(Other) 10330 5(EM100), 25%(Other) 33470 25% 33330 25% 1290 5(12), 20%(35), 25%(Other) 1290 5(12), 20%(Other) 4090 25% 90 25% BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 HK0402/HKQ0402 HK0603 HK1005 HK1608 HK2125 HKQ0603W/HKQ0603C/HKQ0603S/ HKQ0603U AQ105 BK0402Series Measuring frequency : 1001MHz Measuring equipment : E4991Aor its equivalent Measuring jig : 16197Aor its equivalent BK0603Series, BKP0603Series Measuring frequency : 1001MHz Measuring equipment : 4291Aor its equivalent Measuring jig : 16193Aor its equivalent BK1005Series, BKP1005Series ,BKH1005Series Measuring frequency : 1001MHz Measuring equipment : 4291Aor its equivalent Measuring jig : 16192Aor its equivalent, 16193Aor its equivalent BK16082125Series, BKP16082125Series Measuring frequency : 1001MHz Measuring equipment : 4291Aor its equivalent, 4195Aor its equivalent Measuring jig : 16092Aor its equivalent or 16192Aor its equivalent/HW BK20103216Series, MCFSeries Measuring frequency : 1001MHz Measuring equipment : 4291Aor its equivalent, 4195Aor its equivalent Measuring jig : 16192Aor its equivalent This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E02R01 5. Inductance BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY Specified Value BK2010 BK3216 BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 HK0402 HK0603 HK1005 HK1608 HK2125 HKQ0402 HKQ0603W HKQ0603C HKQ0603S HKQ0603U AQ105 CKLKCKPNM Series Measuring frequency Measuring frequency Measuring frequency Measuring frequency Measuring frequency Measuring frequency Measuring frequency Measuring equipment /jig Test Methods and Remarks Measuring current HKHKQAQ Series Measuring frequency Measuring frequency Measuring frequency Measuring frequency Measuring frequency Measuring equipment /jig 4.710.0H 20% 0.110.0H 20% 1.010.0H 20% 0.332.2H 20% 0.474.7H 20% 0.474.7H 20% 0.474.7H 20% 0.821.0H 20% 1.02.2H 20% 0.122.2H 10 or 20% 0.04733.0H 20% 0.1012.0H 10% 0.04733.0H 20% 0.1012.0H 10% 1.05.6nH 0.3nH 6.812nH 5% 1.06.2nH 0.3nH 6.8100nH 5% 1.06.2nH 0.3nH 6.8270nH 5% 1.05.6nH 0.3nH 6.8470nH 5% 1.55.6nH 0.3nH 6.8470nH 5% 0.53.9nH 0.1 or 0.2 or 0.3nH 4.35.6nH 0.3nH or 3% 6.227nH 3 or 5% 0.63.9nH 0.1 or 0.2 or 0.3nH 4.36.2nH 0.2 or 0.3nH or 3 or 5% 6.8100nH 3 or 5% 0.63.9nH 0.1 or 0.2 or 0.3nH 4.36.2nH 0.2 or 0.3nH 6.822nH 3 or 5% 0.66.2nH 0.2 or 0.3nH 6.822nH 3 or 5% 0.64.2nH 0.1 or 0.2 or 0.3nH 4.36.5nH 0.2 or 0.3nH 6.822nH 3 or 5% 1.06.2nH 0.3nH 6.815nH 5% : 24MHzCK1608 : 225MHzCK2125 : 210MHzCKS2125 : 1025MHzLK1005 : 150MHzLK1608 : 0.450MHzLK2125 : 1MHzCKP1608CKP2012CKP2016CKP2520NM2012NM2520 :4194A16085B16092Aor its equivalent 4195A4195116092Aor its equivalent 4294A16192Aor its equivalent 4291A16193Aor its equivalent/LK1005 4285A42841A42842C4285161100CKP1608CKP2012CKP2016CKP2520NM2012NM2520 :1mA rms0.0474.7H 0.1mA rms5.633H : 100MHzHK0402HK0603HK1005AQ105 : 50/100MHzHK1608HK2125 : 500MHzHKQ0603CHKQ0603SHKQ0603U : 300/500MHzHKQ0603W : 100/500MHzHKQ0402 :4291A16197Aor its equivalent/HK0603AQ105 4291A16193Aor its equivalent/HK1005 E4991A16197Aor its equivalent/HKQ0603SHKQ0603UHKQ0603WHKQ0603C 4291A16092A in-house made jigor its equivalent/HK1608HK2125 E4991A16196Dor its equivalent/HK0402HKQ0402 This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E02R01 6. Q BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY BK2010 BK3216 BKP0603 BKP1005 BKP1608 BKP2125 Specified Value MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 HK0402 HK0603 HK1005 HK1608 HK2125 HKQ0402 HKQ0603W HKQ0603C HKQ0603S HKQ0603U AQ105 LKSeries Measuring Measuring Measuring Measuring 1020 min. 1035 min. 1550 min. 3 min. 45 min. 8 min. 812 min. 1018 min. 38 min. 615 min. 1415 min. 1013 min. 14 min. 8 min. frequency frequency frequency equipment /jig Measuring current Test Methods and Remarks HKHKQAQ Series Measuring frequency Measuring frequency Measuring frequency Measuring frequency Measuring frequency Measuring equipment /jig : 1025MHzLK1005 : 150MHzLK1608 : 0.450MHzLK2125 :4194A16085B16092Aor its equivalent 4195A4195116092Aor its equivalent 4294A16192Aor its equivalent 4291A16193Aor its equivalent/LK1005 1mA rms0.0474.7H 0.1mA rms5.633H : 100MHzHK0402HK0603HK1005AQ105 : 50/100MHzHK1608HK2125 : 500MHzHKQ0603CHKQ0603SHKQ0603U : 300/500MHzHKQ0603W : 100/500MHzHKQ0402 :4291A16197Aor its equivalent/HK0603AQ105 4291A16193Aor its equivalent/HK1005 E4991A16197Aor its equivalent/HKQ0603SHKQ0603UHKQ0603WHKQ0603C 4291A16092A in-house made jigor its equivalent/HK1608, HK2125 E4991A16196Dor its equivalentHK0402HKQ0402 This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E02R01 7. DC Resistance BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY Specified Value Test Methods and Remarks BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 HK0402 HK0603 HK1005 HK1608 HK2125 HKQ0402 HKQ0603W HKQ0603C BK2010 BK3216 0.070.75 max. 0.0651.50 max. 0.030.90 max. 1.503.20 max. 0.852.00 max. 0.051.10 max. 0.050.75 max. 0.100.90 max. 0.150.80 max. 0.0300.180 max. 0.02730.220 max. 0.0250.18 max. 0.0200.075 max. 2.56.5 max 2.56.5 max. 2.54.5 max. 4.5 max. 0.450.8530% 0.160.65 max. 0.120.52 max. 0.150.35 max. 0.080.28 max. 0.0750.20 max 0.050.16 max. 0.100.15 max. 0.110.22 max. 0.411.16 max. 0.22.2 max. 0.11.1 max. 0.180.99 max. 0.113.74 max. 0.084.8 max. 0.052.6 max. 0.101.5 max. 0.082.24 max. 0.074.1 max. 0.071.6 max. HKQ0603S 0.061.29 max. HKQ0603U AQ105 0.061.29 max. 0.070.45 max. Measuring equipmentVOAC-7412, VOAC-7512, VOAC-7521made by Iwasaki Tsushinki This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E02R01 8. Self Resonance FrequencySRF BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY BK2010 BK3216 BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 Specified Value Test Methods and Remarks MCF 2010 CK1608 CK2125 CKS2125 CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 HK0402 HK0603 HK1005 HK1608 HK2125 1725MHz min. 24235MHz min. 2475MHz min. 40180MHz min. 9260MHz min. 13320MHz min. 290010000MHz min. 90010000MHz min. 40010000MHz min. 30010000MHz min. 2004000MHz min. HKQ0402 170010000MHz min. HKQ0603W HKQ0603C HKQ0603S HKQ0603U AQ105 LKCK Series : Measuring equipment Measuring jig HKHKQAQ Series : Measuring equipment 80010000MHz min. 250010000MHz min. 190010000MHz min. 190010000MHz min. 230010000MHz min. : 4195Aor its equivalent : 4195116092Aor its equivalent : 8719Cor its equivalent8753Dor its equivalent/HK2125 This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E02R01 9. Temperature Characteristic BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY Specified Value Test Methods and Remarks BK2010 BK3216 BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 HK0402 HK0603 HK1005 HK1608 HK2125 HKQ0402 HKQ0603W HKQ0603C HKQ0603S HKQ0603U AQ105 HKHKQAQ Series Temperature range Reference temperature Inductance changeWithin 10 : 3085 : 20 This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E02R01 10. Resistance to Flexure of Substrate BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 BK2010 ARRAY BK3216 BKP0603 BKP1005 BKP1608 BKP2125 Specified Value MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 HK0402 HK0603 HK1005 HK1608 HK2125 HKQ0402 HKQ0603W HKQ0603C HKQ0603S HKQ0603U AQ105 Warp Testing board Thickness Test Methods and Remarks No mechanical damage. : 2mmBK Series without 0402sizeBKPBKH1005CKCKSCKPNMLKHKHKQ0603SHKQ0603U AQ SeriesMCF1210 : 1mmBK0402BKH0603HK0402HKQ0402HKQ0603WHKQ0603C SeriesMCF Series without 1210 size, : glass epoxy-resin substrate : 0.8mm 20 R-230 Board Warp Deviation1 45 45 Unitmm This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E02R01 11. Solderability BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY Specified Value Test Methods and Remarks BK2010 BK3216 BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 HK0402 HK0603 HK1005 HK1608 HK2125 HKQ0402 HKQ0603W HKQ0603C HKQ0603S HKQ0603U AQ105 Solder temperature Solder temperature Duration At least 75 of terminal electrode is covered by new solder. At least 75 of terminal electrode is covered by new solder. 2305 (JIS Z 3282 H60A or H63A) 2453 (Sn/3.0Ag/0.5Cu) 41 sec. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E02R01 12. Resistance to Soldering BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY Specified Value BK2010 BK3216 BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 Test Methods and Remarks HK0402 HK0603 HK1005 HK1608 HK2125 HKQ0402 HKQ0603W HKQ0603C HKQ0603S HKQ0603U AQ105 Solder temperature Duration Preheating temperature Preheating time Flux Recovery AppearanceNo significant abnormality Impedance changeWithin 30 AppearanceNo significant abnormality Impedance changeWithin 20 No mechanical damage. Remaining terminal electrode70 min Inductance change R104R7 Within 10 6R8100 Within 15 CKS2125 Within 20 CKP1608CKP2012CKP2016CKP2520NM2012NM2520 Within 30 No mechanical damage. Remaining terminal electrode70 min. Inductance change Within 15 No mechanical damage. Remaining terminal electrode70 min. Inductance change 47N4R7 Within 10 5R6330 Within 15 No mechanical damage. Remaining terminal electrode70 min. Inductance change Within 5 2605 100.5 sec. 150 to 180 3 min. Immersion into methanol solution with colophony for 3 to 5 sec. 2 to 3 hrs of recovery under the standard condition after the test.See Note 1 This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E02R01 13. Thermal Shock BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY BK2010 BK3216 AppearanceNo significant abnormality Impedance change Within 30 BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 AppearanceNo significant abnormality Impedance change Within 20 MCF 1210 MCF 2010 CK1608 No mechanical damage. CK2125 Inductance changeWithin 20 Q changeWithin 30 Inductance changeWithin 20 CKS2125 CKS2125 Specified Value CKP1608 CKP2012 CKP2016 No mechanical damage. Inductance change Within 30 CKP2520 NM2012 NM2520 LK1005 No mechanical damage. LK1608 Inductance change Within 10 Q change Within 30 LK2125 HK0402 HK0603 HK1005 HK1608 HK2125 No mechanical damage. HKQ0402 Inductance change Within 10 Q change Within 20 HKQ0603W HKQ0603C HKQ0603S HKQ0603U AQ105 Conditions for 1 cycle Step temperature timemin. 1 Minimum operating temperature 0/3 303 Test Methods and 2 Room temperature 23 Remarks 3 Maximum operating temperature 3/0 303 4 Room temperature 23 Number of cycles5 Recovery2 to 3 hrs of recovery under the standard condition after the test.See Note 1 (Note 1) When there are questions concerning measurement resultmeasurement shall be made after 482 hrs of recovery under the standard condition. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E02R01 14. Damp Heat Steady state BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY Specified Value BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 HK0402 HK0603 HK1005 HK1608 HK2125 HKQ0402 HKQ0603W HKQ0603C HKQ0603S HKQ0603U AQ105 BKBKPBKH Temperature Humidity Duration Recovery Test Methods and Remarks BK2010 BK3216 AppearanceNo significant abnormality Impedance change Within 30 AppearanceNo significant abnormality Impedance change Within 20 No mechanical damage. Inductance change Within 20 Q change Within 30 Inductance change Within 20 No mechanical damage. Inductance change Within 30 No mechanical damage. Inductance change Within 10 Q change Within 30 No mechanical damage. Inductance change Within 20 Q change Within 30 No mechanical damage. Inductance change Within 10 Q change Within 20 SeriesMCF Series 402 90 to 95RH 50024/0 hrs 2 to 3 hrs of recovery under the standard condition after the removal from test chamber.See Note 1 LKCKCKSCKPNMHKHKQAQ Series Temperature 402 LKCKCKSCKPNM Series 602 HKHKQAQ Series Humidity 90 to 95RH Duration 50012 hrs Recovery 2 to 3 hrs of recovery under the standard condition after the removal from test chamber.See Note 1 This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E02R01 15. Loading under Damp Heat BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY BKP0603 BKP1005 BKP1608 BKP2125 CK1608 CK2125 CKS2125 Specified Value CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 BK2010 BK3216 AppearanceNo significant abnormality Impedance change Within 30 No mechanical damage. Inductance change Within 20 Q change Within 30 No mechanical damage. Inductance change Within 20 No mechanical damage. Inductance change Within 30 No mechanical damage. Inductance change Within 10 Q change Within 30 No mechanical damage. Inductance change 0.04712.0H Within 10 15.033.0H Within 15 Q change Within 30 No mechanical damage. Inductance change Within 20 Q change Within 30 HK0402 HK0603 HK1005 HK1608 HK2125 No mechanical damage. HKQ0402 Inductance change Within 10 Q change Within 20 HKQ0603W HKQ0603C HKQ0603S HKQ0603U AQ105 BKBKPBKH Series Temperature 402 Humidity 90 to 95RH Applied current Rated current Duration 50024/0 hrs Recovery 2 to 3 hrs of recovery under the standard condition after the removal from test chamber.See Note 1 Test Methods and LKCKCKSCKPNKHKHKQAQ Series Remarks Temperature 402 LKCKCKSCKPNM Series 602 HKHKQAQ Series Humidity 90 to 95RH Applied current Rated current Duration 50012 hrs Recovery 2 to 3 hrs of recovery under the standard condition after the removal from test chamber.See Note 1 Note on standard condition: "standard condition" referred to herein is defined as follows: 5 to 35 of temperature, 45 to 85% relative humidity, and 86 to 106kPa of air pressure. When there are questions concerning measurement results: In order to provide correlation data, the test shall be conducted under condition of 202 of temperature, 60 to 70% relative humidity, and 86 to 106kPa of air pressure. Unless otherwise specified, all the tests are conducted under the "standard condition." (Note 1) Measurement shall be made after 482 hrs of recovery under the standard condition. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E02R01 16. Loading at High Temperature BK0402 BK0603 BK1005 BKH0603 BKH1005 BK1608 BK2125 ARRAY BKP0603 BKP1005 BKP1608 BKP2125 MCF 0605 MCF 0806 MCF 1210 MCF 2010 CK1608 CK2125 CKS2125 Specified Value CKP1608 CKP2012 CKP2016 CKP2520 NM2012 NM2520 LK1005 LK1608 LK2125 BK2010 BK3216 AppearanceNo significant abnormality Impedance change Within 30 AppearanceNo significant abnormality Impedance change Within 20 No mechanical damage. Inductance change Within 20 Q change Within 30 No mechanical damage. Inductance change Within 20 No mechanical damage. Inductance change Within 30 No mechanical damage. Inductance change Within 10 Q change Within 30 No mechanical damage. Inductance change 0.04712.0H Within 10 15.033.0H Within 15 Q change Within 30 No mechanical damage. Inductance change Within 20 Q change Within 30 HK0402 HK0603 HK1005 HK1608 HK2125 No mechanical damage. HKQ0402 Inductance change Within 10 Q change Within 20 HKQ0603W HKQ0603C HKQ0603S HKQ0603U AQ105 BKBKHBKP SeriesMCF Series Temperature : 1253BKBKH Series : 853BKPMCF Series Applied current Rated current Duration 50024/0 hrs Recovery 2 to 3 hrs of recovery under the standard condition after the removal from test chamber. See Note 1 Test Methods and Remarks LKCKCKSCKPNMHKHKQAQ Series Temperature : 852LKCKCKSCKPNM Series : 852HK16082125 : 852HK1005, AQ105 operating temperature range5585 : 1252HK0402, HKQ0402, HK0603, HK1005, HKQ0603S, HKQ0603U, HKQ0603W, HKQ0603C, AQ105 operating temperature range55125 Applied current Rated current Duration 50012 hrs Recovery 2 to 3 hrs of recovery under the standard condition after the test.See Note 1 Note on standard condition: "standard condition" referred to herein is defined as follows: 5 to 35 of temperature, 45 to 85% relative humidity, and 86 to 106kPa of air pressure. When there are questions concerning measurement results: In order to provide correlation data, the test shall be conducted under condition of 202 of temperature, 60 to 70% relative humidity, and 86 to 106kPa of air pressure. Unless otherwise specified, all the tests are conducted under the "standard condition." (Note 1) Measurement shall be made after 482 hrs of recovery under the standard condition. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_reli_e-E02R01 Precautions on the use of Multilayer chip inductors Multilayer chip inductors for high frequency, Multilayer chip bead inductors Multilayer common mode choke coilsMC series F type PRECAUTIONS 1. Circuit Design Precautions Verification of operating environment, electrical rating and performance 1. A malfunction in medical equipment, spacecraft, nuclear reactors, etc. may cause serious harm to human life or have severe social ramifications. As such, any inductors to be used in such equipment may require higher safety and/or reliability considerations and should be clearly differentiated from components used in general purpose applications. Operating CurrentVerification of Rated current 1. The operating current for inductors must always be lower than their rated values. 2. Do not apply current in excess of the rated value because the inductance may be reduced due to the magnetic saturation effect. 2. PCB Design Precautions Pattern configurationsDesign of Land-patterns 1. When inductors are mounted on a PCB, the size of land patterns and the amount of solder usedsize of filletcan directly affect inductor performance. Therefore, the following items must be carefully considered in the design of solder land patterns: 1 The amount of solder applied can affect the ability of chips to withstand mechanical stresses which may lead to breaking or cracking. Therefore, when designing land-patterns it is necessary to consider the appropriate size and configuration of the solder pads which in turn determines the amount of solder necessary to form the fillets. 2 When more than one part is jointly soldered onto the same land or pad, the pad must be designed so that each component's soldering point is separated by solder-resist. 3 The larger size of land patterns and amount of solder, the smaller Q value after mounting on PCB. It makes higher the Q value to design land patterns smaller than terminal electrode of chips. Pattern configurationsInductor layout on panelized breakaway PC boards 1. After inductors have been mounted on the boards, chips can be subjected to mechanical stresses in subsequent manufacturing processes PCB cutting, board inspection, mounting of additional parts, assembly into the chassis, wave soldering the reflow soldered boards etc.For this reason, planning pattern configurations and the position of SMD inductors should be carefully performed to minimize stress. Pattern configurationsDesign of Land-patterns 1. The following diagrams and tables show some examples of recommended patterns to prevent excessive solder amountslarger fillets which extend above the component end terminations. Examples of improper pattern designs are also shown. 1 Recommended land dimensions for a typical chip inductor land patterns for PCBs Land pattern Solder-resist Chip inductor Chip inductor W C B Technical considerations A B L Recommended land dimensions for wave-soldering Type 1608 2012 2125 L 1.6 2.0 2.0 Size W 0.8 1.25 1.25 A 0.81.0 1.01.4 1.01.4 B 0.50.8 0.81.5 0.81.5 C 0.60.8 0.91.2 0.91.2 Recommended land dimensions for reflow-soldering Type 0402 0603 1005 L 0.4 0.6 1.0 Size W 0.2 0.3 0.5 A 0.150.25 0.200.30 0.450.55 B 0.100.20 0.200.30 0.400.50 C 0.150.30 0.250.40 0.450.55 Type L Size W A B C 2125 2.0 1.25 0.81.2 0.81.2 0.91.6 2016 2.0 1.6 0.81.2 0.81.2 1.22.0 2520 2.5 2.0 1.01.4 0.61.0 1.82.2 Unitmm 2016 2520 2.0 2.5 1.6 2.0 1.01.4 1.01.4 0.81.5 0.61.0 1.31.6 1.62.0 Unitmm 105 1.0 0.6 0.500.55 0.300.40 0.600.70 1608 1.6 0.8 0.81.0 0.60.8 0.60.8 3216 3.2 1.6 1.82.5 0.81.7 1.21.6 2012 2.0 1.25 0.81.2 0.81.2 0.91.6 3216 3.2 1.6 1.82.5 0.61.5 1.22.0 This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_prec_e-E02R01 b b a a a a Excess solder can affect the ability of chips to withstand mechanical stresses. Therefore, please take proper precautions when designing land-patterns. Recommended land dimension for Reflow-soldering d c c Type 3216 2010 1210 0806 0605 L 3.2 2.0 1.25 0.85 0.65 Size W 1.6 1.0 1.0 0.65 0.50 a 0.70.9 0.50.6 0.450.55 0.250.35 0.270.33 b 0.81.0 c 0.40.5 d 0.8 Unitmm d 2 Examples of good and bad solder application Item 0.50.6 0.20.3 0.5 0.70.8 0.250.35 0.170.23 0.250.35 0.250.35 0.200.26 0.55 0.5 0.4 Not recommended Recommended Lead wire of component Solder-resist Mixed mounting of SMD and leaded components Chassis Solder (for grounding) Solder-resist Component placement close to the chassis Electrode pattern Lead wire of component Soldering iron Hand-soldering of leaded components near mounted components Solder-resist Solder-resist Horizontal component placement Pattern configurationsInductor layout on panelized breakaway PC boards 1-1. The following are examples of good and bad inductor layout; SMD inductors should be located to minimize any possible mechanical stresses from board warp or deflection. Item Not recommended Recommended Position the component at a right angle to the direction of the mechanical stresses that are anticipated. Deflection of the board 1-2. To layout the inductors for the breakaway PC board, it should be noted that the amount of mechanical stresses given will vary depending on inductor layout. An example below should be counted for better design. E D Perforation C A B Slit Magnitude of stress ABCDE 1-3. When breaking PC boards along their perforations, the amount of mechanical stress on the inductors can vary according to the method used. The following methods are listed in order from least stressful to most stressful: push-back, slit, V-grooving, and perforation. Thus, any ideal SMD inductor layout must also consider the PCB splitting procedure. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_prec_e-E02R01 3. Considerations for automatic placement Precautions Adjustment of mounting machine 1. Excessive impact load should not be imposed on the inductors when mounting onto the PC boards. 2. The maintenance and inspection of the mounter should be conducted periodically. Selection of Adhesives 1. Mounting inductors with adhesives in preliminary assembly, before the soldering stage, may lead to degraded inductor characteristics unless the following factors are appropriately checked; the size of land patterns, type of adhesive, amount applied, hardening temperature and hardening period. Therefore, it is imperative to consult the manufacturer of the adhesives on proper usage and amounts of adhesive to use. Adjustment of mounting machine 1. If the lower limit of the pick-up nozzle is low, too much force may be imposed on the inductors, causing damage. To avoid this, the following points should be considered before lowering the pick-up nozzle: 1 The lower limit of the pick-up nozzle should be adjusted to the surface level of the PC board after correcting for deflection of the board. 2 The pick-up pressure should be adjusted between 1 and 3N static loads. 3 To reduce the amount of deflection of the board caused by impact of the pick-up nozzle, supporting pins or back-up pins should be used under the PC board. The following diagrams show some typical examples of good pick-up nozzle placement: Item Improper method Proper method Single-sided mounting chipping or cracking supporting pins or back-up pins Double-sided mounting chipping or cracking Technical considerations supporting pins or back-up pins 2. As the alignment pin wears out, adjustment of the nozzle height can cause chipping or cracking of the inductors because of mechanical impact on the inductors. To avoid this, the monitoring of the width between the alignment pin in the stopped position, and maintenance, inspection and replacement of the pin should be conducted periodically. Selection of Adhesives 1. Some adhesives may cause reduced insulation resistance. The difference between the shrinkage percentage of the adhesive and that of the inductors may result in stresses on the inductors and lead to cracking. Moreover, too little or too much adhesive applied to the board may adversely affect component placement, so the following precautions should be noted in the application of adhesives. 1 Required adhesive characteristics a. The adhesive should be strong enough to hold parts on the board during the mounting & solder process. b. The adhesive should have sufficient strength at high temperatures. c. The adhesive should have good coating and thickness consistency. d. The adhesive should be used during its prescribed shelf life. e. The adhesive should harden rapidly. f. The adhesive must not be contaminated. g. The adhesive should have excellent insulation characteristics. h. The adhesive should not be toxic and have no emission of toxic gasses. 2 When using adhesives to mount inductors on a PCB, inappropriate amounts of adhesive on the board may adversely affect component placement. Too little adhesive may cause the inductors to fall off the board during the solder process. Too much adhesive may cause defective soldering due excessive flow of adhesive on to the land or solder pad. Amount of adhesives After inductors are bonded Recommended conditions a a Figure 0805 case sizes as examples a 0.3mm min b b 100120m c Area with no adhesive c c 4. Soldering Precautions Selection of Flux 1. Since flux may have a significant effect on the performance of inductors, it is necessary to verify the following conditions prior to use; 1 Flux used should be with less than or equal to 0.1 wt% Chlorine conversion method of halogenated content. Flux having a strong acidity content should not be applied. 2 When soldering inductors on the board, the amount of flux applied should be controlled at the optimum level. 3 When using water-soluble flux, special care should be taken to properly clean the boards. Soldering 1. Temperature, time, amount of solder, etc. are specified in accordance with the following recommended conditions, and please contact us about peak temperature when you use lead-free paste. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_prec_e-E02R01 Selection of Flux 1-1. When too much halogenated substanceChlorine, etc.content is used to activate the flux, or highly acidic flux is used, an excessive amount of residue after soldering may lead to corrosion of the terminal electrodes or degradation of insulation resistance on the surface of the Inductor. 1-2. Flux is used to increase solderability in flow soldering, but if too much is applied, a large amount of flux gas may be emitted and may detrimentally affect solderability. To minimize the amount of flux applied, it is recommended to use a flux-bubbling system. 1-3. Since the residue of water-soluble flux is easily dissolved by water content in the air, the residue on the surface of Inductor in high humidity conditions may cause a degradation of insulation resistance and therefore affect the reliability of the components. The cleaning methods and the capability of the machines used should also be considered carefully when selecting water-soluble flux. Soldering 1-1. Preheating when soldering Heating: Chip inductor components should be preheated to within 100 to 130 of the soldering. Cooling: The temperature difference between the components and cleaning process should not be greater than 100. Chip inductors are susceptible to thermal shock when exposed to rapid or concentrated heating or rapid cooling. Therefore, the soldering process must be conducted with a great care so as to prevent malfunction of the components due to excessive thermal shock. Recommended conditions for soldering Pb free soldering Reflow soldering Temperature profile 300 300 Peak 260 Max. Within 10sec. 230 Within 10sec. 60sec. 60sec Min. 200 Min. Temperature Temperature Preheating Slow cooling 100 0 200 Slow cooling 100 0 Preheating150 Heating above 230 60sec. Min. 40sec. Max. Ceramic chip components should be preheated to within 100 to 130 of the soldering. Assured to be reflow soldering for 2 times. Caution 1. The ideal condition is to have solder massfilletcontrolled to 1/2 to 1/3 of the thickness of the inductor, as shown below: 1/2T1/3T Inductor Solder Technical considerations T PC board 2. Because excessive dwell times can detrimentally affect solderability, soldering duration should be kept as close to recommended times as possible. Wave soldering Temperature profile 300 Preheating 120sec. Min. Peak 260 Max. Within 10sec. 230250 Within 3sec. 200 Slow cooling 100 Temperature Temperature 300 200 120sec. Min. Preheating 150 100 Slow cooling 0 0 Ceramic chip components should be preheated to within 100 to 130 of the soldering. Assured to be wave soldering for 1 time. Except for reflow soldering type. Caution 1. Make sure the inductors are preheated sufficiently. 2. The temperature difference between the inductor and melted solder should not be greater than 100 to 130. 3. Cooling after soldering should be as gradual as possible. 4. Wave soldering must not be applied to the inductors designated as for reflow soldering only. Hand soldering Temperature profile 400 400 Peak 350 Max. Within 3sec. 230280 Within 3sec. 300 200 Slow cooling 100 0 Preheating 60sec. Min. Temperature Temperature 300 T Slow cooling 200 100 0 Preheating 150 Min. 60sec. Min. 190 3216Type max, 130 3225 Type min It is recommended to use 20W soldering iron and the tip is 1 or less. The soldering iron should not directly touch the components. Assured to be soldering iron for 1 time. Note: The above profiles are the maximum allowable soldering condition, therefore these profiles are not always recommended. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_prec_e-E02R01 Caution 1. Use a 20W soldering iron with a maximum tip diameter of 1.0 mm. 2. The soldering iron should not directly touch the inductor. 5. Cleaning Precautions Cleaning conditions 1. When cleaning the PC board after the Inductors are all mounted, select the appropriate cleaning solution according to the type of flux used and purpose of the cleaninge.g. to remove soldering flux or other materials from the production process. 2. Cleaning conditions should be determined after verifying, through a test run, that the cleaning process does not affect the inductor's characteristics. Technical considerations Cleaning conditions 1. The use of inappropriate solutions can cause foreign substances such as flux residue to adhere to the inductor, resulting in a degradation of the inductor's electrical propertiesespecially insulation resistance. 2. Inappropriate cleaning conditionsinsufficient or excessive cleaningmay detrimentally affect the performance of the inductors. 1 Excessive cleaning a. In the case of ultrasonic cleaning, too much power output can cause excessive vibration of the PC board which may lead to the cracking of the inductor or the soldered portion, or decrease the terminal electrodes' strength. Thus the following conditions should be carefully checked; Ultrasonic output Below 20W/ Ultrasonic frequency Below 40kHz Ultrasonic washing period 5 min. or less 6. Post cleaning processes Precautions Application of resin coatings, moldings, etc. to the PCB and components. 1. With some type of resins a decomposition gas or chemical reaction vapor may remain inside the resin during the hardening period or while left under normal storage conditions resulting in the deterioration of the inductor's performance. 2. When a resin's hardening temperature is higher than the inductor's operating temperature, the stresses generated by the excess heat may lead to inductor damage or destruction. 3. Stress caused by a resin's temperature generated expansion and contraction may damage inductors. The use of such resins, molding materials etc. is not recommended. 7. Handling Precautions Breakaway PC boardssplitting along perforations 1. When splitting the PC board after mounting inductors and other components, care is required so as not to give any stresses of deflection or twisting to the board. 2. Board separation should not be done manually, but by using the appropriate devices. General handling precautions 1. Always wear static control bands to protect against ESD. 2. Keep the inductors away from all magnets and magnetic objects. 3. Use non-magnetic tweezers when handling inductors. 4. Any devices used with the inductors soldering irons, measuring instruments should be properly grounded. 5. Keep bare hands and metal productsi.e., metal deskaway from chip electrodes or conductive areas that lead to chip electrodes. 6. Keep inductors away from items that generate magnetic fields such as speakers or coils. Mechanical considerations 1. Be careful not to subject the inductors to excessive mechanical shocks. 1 If inductors are dropped on the floor or a hard surface they should not be used. 2 When handling the mounted boards, be careful that the mounted components do not come in contact with or bump against other boards or components. 8. Storage conditions Precautions Storage 1. To maintain the solderability of terminal electrodes and to keep the packaging material in good condition, care must be taken to control temperature and humidity in the storage area. Humidity should especially be kept as low as possible. Recommended conditions Ambient temperature Below 40 Humidity Below 70% RH The ambient temperature must be kept below 30. Even under ideal storage conditions inductor electrode solderability decreases as time passes, so inductors should be used within 6 months from the time of delivery. *The packaging material should be kept where no chlorine or sulfur exists in the air. Technical considerations Storage 1. If the parts are stocked in a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration of taping/packaging materials may take place. For this reason, components should be used within 6 months from the time of delivery. If exceeding the above period, please check solderability before using the inductors. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_mlci_prec_e-E02R01