Data Sheet
Broadcom AV02-0171EN
January 30, 2019
Description
These diode-transistor optocouplers use an insulating layer
between a LED and an integrated photodetector to provide
electrical insulation between input and output. Separate
connections for the photodiode bias and output-transistor
collector increase the speed up to a hundred times that of a
conventional phototransistor coupler by reducing the
base-collector capacitance.
These single channel optocoup-lers are available in 8-pin
DIP, SO-8, and Widebody package configurations.
The 6N135, HCPL-0500, and HCNW135 are for use in
TTL/CMOS, TTL/LSTTL or wide-bandwidth analog
applications. Current transfer ratio (CTR) for these devices
is 7% minimum at IF = 16 mA.
The 6N136, HCPL-2502, HCPL-0501, and HCNW136 are
designed for high-speed TTL/TTL applications. A standard
16-mA TTL sink current through the input LED will provide
enough output current for 1 TTL load and a 5.6 k pull-up
resistor. CTR for these devices is 19% minimum at
IF=16mA.
Features
High speed: 1 Mb/s
TTL compatible
Available in 8-pin DIP, SO-8, widebody packages
Open collector output
Safety approval
UL Recognized – 3750 Vrms for 1 minute (5000 Vrms for
1 minute for HCNW and Option 020 devices) per
UL1577
CSA Approved
IEC/EN/DIN EN 60747-5-5 Approved
–V
IORM = 567V peak for SO-8 devices
–V
IORM = 630V peak for DIP 300 mil devices
–V
IORM = 1414V peak for DIP 400 mil (widebody)
devices
Dual channel version available (253X/053X/0534)
Applications
High voltage insulation
Video signal isolation
Line receivers
Feedback element in switched mode power supplies
High speed logic ground isolation
– TTL/TTL, TTL/CMOS, TTL/LSTTL
Replaces pulse transformers
Replaces slow phototransistor isolators
Analog signal ground isolation
CAUTION! Take normal static precautions in handling and
assembly of this component to prevent damage
and/or degradation that may be induced by
ESD.
6N135/6, HCNW135/6, HCPL-2502/0500/
0501
Single-Channel, High-Speed Optocouplers
Broadcom AV02-0171EN
2
6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Single-Channel, High-Speed Optocouplers
Functional Diagram
Truth Table (Positive Logic)
A 0.1-µF bypass capacitor must be connected between pins
5 and 8.
Schematic
LED V0
ON LOW
OFF HIGH
7
1
2
3
45
6
8
NC
ANODE
CATHODE
NC
V
CC
V
B
V
O
GND
TRUTH TABLE
(POSITIVE LOGIC)
LED
ON
OFF
V
O
LOW
HIGH
I
F
SHIELD
8
6
5
GND
V
CC
2
3
V
O
I
CC
V
F
I
O
ANODE
CATHODE
+
-
7
V
B
I
B
Selection Guide
Minimum CMR 8-Pin DIP (300 Mil) Small Outline SO-8
Widebody
(400 Mil)
dV/dT
(V/µs) VCM (V)
Current
Transfer Ratio
(%)
Single Channel
Package
Dual Channel
Packagea
a. Technical data for these products are on separate Broadcom publications.
Single Channel
Package
Dual Channel
Packagea
Single Channel
Package
1000 10 7 6N135 HCPL-2530 HCPL-0500 HCPL-0530 HCNW135
19 6N136 HCPL-2531 HCPL-0501 HCPL-0531 HCNE136
15 HCPL-2502
Broadcom AV02-0171EN
3
6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Single-Channel, High-Speed Optocouplers
Ordering Information
6N135, 6N136, HCPL-2502, HCPL-0500, HCPL-0501 are UL Recognized with 3750 Vrms for 1 minute per UL1577.
HCNW135 and HCNW136 are UL Recognized with 5000 Vrms for 1 minute per UL1577. All these devices are approved
under CSA Component Acceptance Notice #5, File CA 88324.
To order, choose a part number from the part number column and combine with the desired option from the option column
to form an order entry.
Example 1:
HCPL-2502-560E to order product of 300 mil DIP Gull Wing Surface Mount package in Tape and Reel packaging with
IEC/EN/DIN EN 60747-5-5 Safety Approval in RoHS compliant.
Example 2:
HCPL-2502 to order product of 300 mil DIP package in tube packaging and non RoHS compliant.
Optional data sheets are available. Contact your Broadcom® sales representative or authorized distributor for information.
NOTE: The notation ‘#XXX’ is used for existing products, while (new) products launched since 15th July 2001 and RoHS
compliant option will use ‘-XXXE‘.
Part
Number
Option
Package
Surface
Mount
Gull
Wing
Tape and
Reel
UL 3750
Vrms/
1Minute
Rating
UL 5000
Vrms/
1Minute
Rating
IEC/EN/DIN
EN
60747-5-5 Quantity
RoHS
Compliant
Non RoHS
Compliant
6N135
6N136
HCPL-2502
-000E No option 300mil
DIP-8
X 50 per tube
-300E #300 X X X 50 per tube
-500E #500 X X X X 1000 per reel
-020E #020 X 50 per tube
-320E #320 X X X 50 per tube
-520E #520 X X X X 1000 per reel
-060E #060 X X 50 per tube
-360E #360 X X X X 50 per tube
-560E #560 X X X X X 1000 per reel
HCPL-0500
HCPL-0501
-000E No option SO-8 X X 100 per tube
-500E #500 X X X 1500 per reel
-060E #060 X X X 100 per tube
-560E #560 X X X X 1500 per reel
HCNW135
HCNW136
-000E No option 400 mil
Widebody
DIP-8
X X 42 per tube
-300E #300 X X X X 42 per tube
-500E #500 X X X X X 750 per reel
Broadcom AV02-0171EN
4
6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Single-Channel, High-Speed Optocouplers
Package Outline Drawings
8-Pin DIP Package (6N135/6, HCPL-2502)
1.080 ± 0.320
(0.043 ± 0.013)
2.54 ± 0.25
(0.100 ± 0.010)
0.51 (0.020) MIN.
0.65 (0.025) MAX.
4.70 (0.185) MAX.
2.92 (0.115) MIN.
5
q
TYP. 0.254
+ 0.076
- 0.051
(0.010
+ 0.003)
- 0.002)
7.62 ± 0.25
(0.300 ± 0.010)
6.35 ± 0.25
(0.250 ± 0.010)
9.65 ± 0.25
(0.380 ± 0.010)
1.78 (0.070) MAX.
1.19 (0.047) MAX.
A XXXXZ
YYWW
DATE CODE
DIMENSIONS IN MILLIMETERS AND (INCHES).
5678
4321
OPTION CODE*
UL RECOGNITION
UR
TYPE NUMBER
*MARKING CODE LETTER FOR OPTION NUMBERS
"L" = OPTION 020
"V" = OPTION 060
OPTION NUMBERS 300 AND 500 NOT MARKED.
NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
3.56 ± 0.13
(0.140 ± 0.005)
LOT ID
EEE
Broadcom AV02-0171EN
5
6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Single-Channel, High-Speed Optocouplers
8-Pin DIP Package with Gull Wing Surface Mount Option 300 (6N135/6)
0.635 ± 0.25
(0.025 ± 0.010)
12
q
NOM.
9.65 ± 0.25
(0.380 ± 0.010)
0.635 ± 0.130
(0.025 ± 0.005)
7.62 ± 0.25
(0.300 ± 0.010)
5
6
7
8
4
3
2
1
9.65 ± 0.25
(0.380 ± 0.010)
6.350 ± 0.25
(0.250 ± 0.010)
1.016 (0.040)
1.27 (0.050)
10.9 (0.430)
2.0 (0.080)
LAND PATTERN RECOMMENDATION
1.080 ± 0.320
(0.043 ± 0.013)
3.56 ± 0.13
(0.140 ± 0.005)
1.780
(0.070)
MAX.
1.19
(0.047)
MAX.
2.54
(0.100)
BSC
DIMENSIONS IN MILLIMETERS (INCHES).
LEAD COPLANARITY = 0.10 mm (0.004 INCHES).
NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
0.254
+ 0.076
- 0.051
(0.010
+ 0.003)
- 0.002)
Broadcom AV02-0171EN
6
6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Single-Channel, High-Speed Optocouplers
Small Outline SO-8 Package (HCPL-0500/1)
XXX
YWW
4321
5.994 ± 0.203
(0.236 ± 0.008)
3.937 ± 0.127
(0.155 ± 0.005)
0.406 ± 0.076
(0.016 ± 0.003)
1.270
(0.050) BSC
5.080 ± 0.127
(0.200 ± 0.005)
3.175 ± 0.127
(0.125 ± 0.005)
1.524
(0.060)
45 q X 0.432
(0.017)
0.228 ± 0.025
(0.009 ± 0.001)
TYPE NUMBER
(LAST 3 DIGITS)
DATE CODE
0.305
(0.012) MIN.
TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH)
5.207 ± 0.254 (0.205 ± 0.010)
DIMENSIONS IN MILLIMETERS (INCHES).
LEAD COPLANARITY = 0.10 mm (0.004 INCHES) MAX.
0.203 ± 0.102
(0.008 ± 0.004)
7q
PIN ONE
0 ~ 7q
*
*
7.49 (0.295)
1.9 (0.075)
0.64 (0.025)
LAND PATTERN RECOMMENDATION
5678
LOT ID
EEE
Broadcom AV02-0171EN
7
6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Single-Channel, High-Speed Optocouplers
8-Pin Widebody DIP Package (HCNW135/6)
5
6
7
8
4
3
2
1
11.23 ± 0.15
(0.442 ± 0.006)
1.8 ± 0.15
5.10
(0.201) MAX.
1.55
(0.061)
MAX.
2.54 (0.100)
TYP. DIMENSIONS IN MILLIMETERS (INCHES).
NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
7
q
TYP.
0.254 + 0.076
- 0.0051
(0.010
- 0.002)
(0.433)
9.00 ± 0.15
(0.354 ± 0.006)
MAX.
10.16 (0.400)
TYP.
A
HCNWXXXX
YYWW
DATE CODE
TYPE NUMBER
0.51 (0.021) MIN.
0.40 (0.016)
0.56 (0.022)
3.10 (0.122)
3.90 (0.154)
LOT ID
EEE
Broadcom AV02-0171EN
8
6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Single-Channel, High-Speed Optocouplers
8-Pin Widebody DIP Package with Gull Wing Surface Mount Option 300
(HCNW135/6)
Solder Reflow Profile
Recommended reflow conditions are as per JEDEC Standard, J-STD-020 (latest revision). Non-halide flux should be used.
Regulatory Information
The devices contained in this data sheet have been approved by the following organizations:
UL Approval under UL 1577, Component Recognition Program, File E55361.
CSA Approval under CSA Component Acceptance Notice #5, File CA 88324.
IEC/EN/DIN EN 60747-5-5 (HCNW and Option 060/360/560 only)
1.00 ± 0.15
(0.039 ± 0.006)
7q NOM.
12.30 ± 0.30
(0.484 ± 0.012)
0.75 ± 0.25
(0.030 ± 0.010)
11.00
(0.433)
5
6
7
8
4
3
2
1
11.23
±
0.15
(0.442 ± 0.006)
9.00 ± 0.15
(0.354 ± 0.006)
1.3
(0.051)
13.56
(0.534)
2.29
(0.09)
LAND PATTERN RECOMMENDATION
1.80 ± 0.15
(0.071 ± 0.006)
4.00
(0.158) MAX.
1.55
(0.061)
MAX.
2.54
(0.100)
BSC
DIMENSIONS IN MILLIMETERS (INCHES).
LEAD COPLANARITY = 0.10 mm (0.004 INCHES).
NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
0.254
+ 0.076
- 0.0051
(0.010
+ 0.003)
- 0.002)
MAX.
Broadcom AV02-0171EN
9
6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Single-Channel, High-Speed Optocouplers
Insulation and Safety Related Specifications
Option 300 – Surface mount classification is Class A in accordance with CECC 00802.
Parameter Symbol
8-Pin DIP
(300 Mil)
Value SO-8 Value
Widebody
(400 Mil)
Value Units Conditions
Minimum External Air Gap
(External Clearance)
L(101) 7.1 4.9 9.6 mm Measured from input terminals to output
terminals, shortest distance through air.
Minimum External Tracking
(External Creepage)
L(102) 7.4 4.8 10.0 mm Measured from input terminals to output
terminals, shortest distance path along
body..
Minimum Internal Plastic
Gap
(Internal Clearance)
0.08 0.08 1.0 mm Through insulation distance conductor
to conductor, usually the direct distance
between the photoemitter and
photodetector inside the optocoupler
cavity.
Minimum Internal Tracking
(Internal Creepage)
N/A N/A 4.0 mm Measured from input terminals to output
terminals, along internal cavity.
Tracking Resistance
(Comparative Tracking
Index)
CTI 200 200 200 V DIN IEC 112/VDE 0303 Part 1
Isolation Group IIIa IIIa IIIa Material Group
(DIN VDE 0110, 1/89, Table 1)
Broadcom AV02-0171EN
10
6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Single-Channel, High-Speed Optocouplers
IEC/EN/DIN EN 60747-5-5 Insulation Characteristicsa (Option 060 Only)
NOTE: Isolation characteristics are guaranteed only within the safety maximum ratings, which must be ensured by
protective circuits in the application.
Description Symbol 8-Pin DIP SO-8 Units
Installation Classification per DIN VDE 0110/39, Table 1
for rated mains voltage 150 Vrms
for rated mains voltage 300 Vrms
for rated mains voltage 600 Vrms
I – IV
I – IV
I – IV
I – IV
I – IV
I – III
Climatic Classification 0/70/21 0/70/21
Pollution Degree (DIN VDE 0110/39) 2 2
Maximum Working Insulation Voltage VIORM 630 567 Vpeak
Input to Output Test Voltage, Method ba
VIORM × 1.875 = VPR, 100% Production Test with tm = 1s, Partial Discharge < 5 pC
a. Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section IEC/EN/DIN EN 60747-5-5, for
a detailed description.
VPR 1181 1063 Vpeak
Input to Output Test Voltage, Method aa
VIORM x 1.6 = VPR, Type and Sample Test, tm = 10s, Partial Discharge < 5 pC
VPR 1008 907 Vpeak
Highest Allowable Overvoltagea (Transient Overvoltage tini = 60s) VIOTM 8000 6000 Vpeak
Safety-limiting values – Maximum Values Allowed in the Event of a Failure
Case Temperature
Input Current
Output Power
TS
IS, INPUT
PS, OUTPUT
175
230
600
150
150
600
°C
mA
mW
Insulation Resistance at TS, VIO = 500V RS≥109≥109
Broadcom AV02-0171EN
11
6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Single-Channel, High-Speed Optocouplers
IEC/EN/DIN EN 60747-5-5 Insulation Characteristicsa (HCNW135/6
Option 060 Only)
NOTE: Isolation characteristics are guaranteed only within the safety maximum ratings, which must be ensured by
protective circuits in the application.
Description Symbol Characteristic Units
Installation Classification per DIN VDE 0110/39, Table 1
for rated mains voltage 150 Vrms
for rated mains voltage 300 Vrms
for rated mains voltage 600 Vrms
for rated mains voltage 1000 Vrms
I – IV
I – IV
I – IV
I – III
Climatic Classification 0/70/21
Pollution Degree (DIN VDE 0110/39) 2
Maximum Working Insulation Voltage VIORM 1414 Vpeak
Input to Output Test Voltage, Method ba
VIORM × 1.875 = VPR, 100% Production Test with tm = 1s, Partial Discharge < 5 pC
a. Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section IEC/EN/DIN EN 60747-5-5, for
a detailed description.
VPR 2651 Vpeak
Input to Output Test Voltage, Method aa
VIORM x 1.6 = VPR, Type and Sample Test, tm = 10s, Partial Discharge < 5 pC
VPR 2262 Vpeak
Highest Allowable Overvoltagea (Transient Overvoltage tini = 60s) VIOTM 8000 Vpeak
Safety-limiting values – Maximum Values Allowed in the Event of a Failure
Case Temperature
Input Current
Output Power
TS
IS, INPUT
PS, OUTPUT
150
400
700
°C
mA
mW
Insulation Resistance at TS, VIO = 500V RS≥109
Broadcom AV02-0171EN
12
6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Single-Channel, High-Speed Optocouplers
Absolute Maximum Rating
Parameter Symbol Device Min. Max. Units Note
Storage Temperaturea
a. Data has been registered with JEDEC for the 6N135/6N136.
TS–55 125 °C
Operating TemperatureaTA8-Pin DIP SO-8 –55 100 °C
Widebody –55 85
Average Forward Input CurrentaIF(AVG) —25mAb
b. Derate linearly above 70°C free-air temperature at a rate of 0.8 mA/°C (8-Pin DIP). Derate linearly above 85°C free-air temperature at a rate
of 0.5 mA/°C (SO-8).
Peak Forward Input Currenta
(50% duty cycle, 1-ms pulse width)
IF(PEAK) 8-Pin DIP SO-8 — 50 mA c
c. Derate linearly above 70°C free-air temperature at a rate of 1.6 mA/°C (8-Pin DIP). Derate linearly above 85°C free-air temperature at a rate
of 1.0 mA/°C (SO-8).
50% duty cycle, 1 ms pulse width Widebody — 40
Peak Transient Input Currenta (1-µs pulse width, 300 pps) IF(TRANS) 8-Pin DIP SO-8 — 1 A
Widebody — 0.1
Reverse LED Input Voltagea (Pin 3-2) VR8-Pin DIP SO-8 — 5 V
Widebody — 3
Input Power Dissipationa PIN 8-Pin DIP SO-8 — 45 mW d
d. Derate linearly above 70°C free-air temperature at a rate of 0.9 mW/°C (8-Pin DIP). Derate linearly above 85°C free-air temperature at a rate
of 1.1 mW/°C (SO-8).
Widebody — 40
Average Output Currenta (Pin 6) IO(AVG) —8mA
Peak Output CurrentaIO(PEAK) —16mA
Emitter-Base Reverse Voltagea (Pin 5-7) VEBR —5 V
Supply Voltage (Pin 8-5) VCC –0.5 30 V
Output Voltage (Pin 6-5) VO–0.5 20 V
Supply Voltagea (Pin 8-5) VCC –0.5 15 V
Output Voltagea (Pin 6-5) VO–0.5 15 V
Base Currenta (Pin 7) IB—5mA
Output Power DissipationaPO—100mW e
e. Derate linearly above 70°C free-air temperature at a rate of 2.0 mW/°C (8-Pin DIP). Derate linearly above 85°C free-air temperature at a rate
of 2.3 mW/°C (SO-8).
Lead Solder Temperaturea (Through-Hole Parts Only)
1.6 mm below seating plane, 10s up to seating plane, 10s
TLS 8-Pin DIP — 260 °C
Widebody 260 °C
Reflow Temperature Profile TRP SO-8 and
Option 300
See Package Outline Drawings
Broadcom AV02-0171EN
13
6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Single-Channel, High-Speed Optocouplers
Electrical Specifications (DC)
Over recommended operating temperature (TA = 0°C to 70°C) and unless otherwise specified. See note.
Parameter Symbol Device Min. Typ.aMax. Units Test Conditions Figure Note
Current Transfer
Ratio
CTRb6N135
HCPL-0500
HCNW135
71850%T
A = 25°C VO = 0.4V IF = 16 mA,
VCC = 4.5V
1, 2, 4c, d
519— V
O = 0.5V
HCPL-2502 15 22 TA = 25°C VO = 0.4V
15 25 — VO = 0.5V
6N136
HCPL-0501
HCNW136
19 24 50 TA = 25°C VO = 0.4V
15 25 — VO = 0.5V
Logic Low
Output Voltage
VOL 6N135
HCPL-0500
HCNW135
—0.10.4 VT
A = 25°C IO = 1.1 mA IF = 16 mA,
VCC = 4.5V
—0.10.5 I
O = 0.8 mA
6N136
HCPL-2502
HCPL-0501
HCNW136
—0.10.4 T
A = 25°C IO = 3.0 mA
—0.10.5 I
O = 2.4 mA
Logic High
Output Current
IOHb— 0.003 0.5 µA TA = 25°C VO = VCC =
5.5V
IF = 0 mA 7
—0.01 1 T
A = 25°C VO = VCC =
15V
——50 V
O = VCC =
15V
Logic Low
Supply Current
ICCL —50200µAI
F = 16 mA, VO = Open, VCC = 15V
Logic High
Supply Current
ICCHb—0.02 1 µAT
A = 25°C IF = 0 mA,
VO = Open
—— 2 V
CC = 15V
Input Forward
Voltage
VFb8-Pin DIP — 1.5 1.7 V TA = 25°C IF = 16 mA 3
SO-8 — — 1.8
Widebody 1.45 1.68 1.85 TA = 25°C IF = 16 mA
1.35 — 1.95
Input Reverse
Breakdown
Voltage
BVRb8-Pin DIP 5 — — V IR = 10 µA
SO-8
Widebody 3 — — IR =
100 µA
Temperature
Coefficient of
Forward Voltage
VF/TA8-Pin DIP — –1.6 mV/°C IF =
16 mA
SO-8
Widebody — –1.9
Input
Capacitance
CIN 8-Pin DIP — 60 — pF f = 1 MHz, VF = 0V
SO-8
Widebody — 90 —
Broadcom AV02-0171EN
14
6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Single-Channel, High-Speed Optocouplers
NOTE: Use of a 0.1-µf bypass capacitor connected between pins 5 and 8 is recommended.
Transistor DC
Current Gain
hFE 8-Pin DIP — 150 — VO = 5V, IO = 3 mA
Widebody — 180 — VO = 5V, IO = 3 mA
—160— V
O = 0.4V, IB = 20 µA
a. All typicals at TA = 25°C.
b. For JEDEC registered parts.
c. CURRENT TRANSFER RATIO in percent is defined as the ratio of output collector current, IO, to the forward LED input current, IF, times 100.
d. The JEDEC registration for the 6N136 specifies a minimum CTR of 15%. Avago guarantees a minimum CTR of 19%.
Parameter Symbol Device Min. Typ.aMax. Units Test Conditions Figure Note
Broadcom AV02-0171EN
15
6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Single-Channel, High-Speed Optocouplers
Switching Specifications (AC)
Over recommended temperature (TA = 0°C to 70°C), VCC = 5V, IF = 16 mA unless otherwise specified.
Parameter Symbol Device Min. Typ.a
a. All typicals at TA = 25°C.
Max. Units Test Conditions Figure Note
Propagation Delay
Time to Logic Low at
Output
tPHLb
b. For JEDEC registered parts.
6N135
HCPL-0500
HCNW135
—0.21.5µsT
A = 25°C RL = 4.1 k5, 6, 11 c, d
c. The 1.9 k load represents 1 TTL unit load of 1.6 mA and the 5.6 k pull-up resistor.
d. The 4.1 k load represents 1 LSTTL unit load of 0.36 mA and 6.1 kpull-up resistor.
6N136
HCPL-2502
HCPL-0501
HCNW136
—0.20.8 T
A = 25°C RL = 1.9 k
——1.0
Propagation Delay
Time to Logic High at
Output
tPLHb6N135
HCPL-0500
HCNW135
—1.31.5µsT
A = 25°C RL = 4.1 k5, 6, 11 c, d
——2.0
6N136
HCPL-2502
HCPL-0501
HCNW136
—0.60.8 T
A = 25°C RL = 1.9 k
——1.0
Common Mode
Transient Immunity at
Logic High Level
Output
|CMH| 6N135 1 — — kV/µs RL = 4.1 kIF = 0 mA,
TA = 25°C,
VCM = 10 Vp-p,
CL = 15 pF
12 c, d, e
e. Common mode transient immunity in a Logic High level is the maximum tolerable (positive) dVCM/dt on the leading edge of the common mode
pulse signal, VCM, to assure that the output will remain in a Logic High state (that is, VO > 2.0V). Common mode transient immunity in a Logic
Low level is the maximum tolerable (negative) dVCM/dt on the trailing edge of the common mode pulse signal, VCM, to assure that the output
will remain in a Logic Low state (that is, VO < 0.8 V).
HCPL-0500
HCNW135
—1—
6N136 1 — — RL = 1.9 k
HCPL-2502
HCPL-0501
—1—
Common Mode
Transient Immunity at
Logic Low Level
Output
|CML| 6N135 1 — — kV/µs RL = 4.1 kIF = 16 mA,
TA = 25°C,
CL = 15 pF
12 c, d, e
HCPL-0500
HCNW135
—1—
6N136 1 — — RL = 1.9 k
HCPL-2502
HCPL-0501
—1—
Bandwidth BW 6N135/6
HCPL-2502
HCPL-0500/1
— 9 — MHz See Test
Circuit
8, 10 f
f. The frequency at which the ac output voltage is 3 dB below its mid-frequency value.
HCNW135/6 — 11 —
Broadcom AV02-0171EN
16
6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Single-Channel, High-Speed Optocouplers
Package Characteristics
Over recommended temperature (TA = 0°C to 70°C) unless otherwise specified.
Parameter Sym. Device Min. Typ.a
a. All typicals at TA = 25°C.
Max. Units Test Conditions Figure Note
Input-Output Momentary
Withstand Voltageb
b. The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous
voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-5 Insulation Related Characteristics Table (if
applicable), your equipment level safety specification or Avago Application Note 1074, Optocoupler Input-Output Endurance Voltage,
publication number 5963-2203E.
VISO 8-Pin DIP
SO-8
3750 — — Vrms RH < 50%, t = 1 min., TA =
25°C
c, d
c. Device considered a two-terminal device: Pins 1, 2, 3, and 4 shorted together and Pins 5, 6, 7, and 8 shorted together.
d. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 4500 Vrms for 1 second (leakage
detection current limit, II-O ≤ 5 µA). This test is performed before the 100% Production test shown in the IEC/EN/DIN EN 60747-5-5 Insulation
Related Characteristics Table if applicable.
Widebody 5000 — — c, e
e. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 6000 Vrms for 1 second (leakage
detection current limit, II-O ≤ 5 µA). This test is performed before the 100% Production test shown in the IEC/EN/DIN EN 60747-5-5 Insulation
Related Characteristics Table if applicable.
8-Pin DIP
(Option 020)
5000 — — c, e, f
f. Refer to the Option 020 data sheet for more information.
II-O 8-Pin DIP — — 1 µA 45% RH, t = 5s,
VI-O = 3 kVdc, TA = 25°C
c, g
g. This rating is equally validated by an equivalent ac proof test.
Input-Output Resistance RI-O 8-Pin DIP
SO-8
—1012 —VI-O = 500 Vdc c
Widebody 1012 1013 —T
A = 25°C
1011 —— T
A = 100°C
Input-Output Capacitance CI-O 8-Pin DIP
SO-8
— 0.6 — pF f = 1 MHz c
Widebody — 0.5 0.6
Broadcom AV02-0171EN
17
6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Single-Channel, High-Speed Optocouplers
Figure 1: DC and Pulsed Transfer Characteristics
Figure 2: Current Transfer Ratio vs. Input Current
Figure 3: Input Current vs. Forward Voltage
10
5
0
01020
V
O
- OUTPUT VOLTAGE - V
40 mA
35 mA
30 mA
25 mA
20 mA
15 mA
10 mA
I = 5 mA
F
T = 25
q
C
V = 5.0 V
A
CC
I
O
Ð OUTPUT CURRENT - mA
8 PIN DIP, SO-8
12
8
001020
V
O
- OUTPUT VOLTAGE - V
40 mA
35 mA
30 mA
25 mA
20 mA
15 mA
10 mA
I = 5 mA
F
I
O
Ð OUTPUT CURRENT Ð mA
4
16
T = 25
q
C
V = 5.0 V
A
CC
WIDEBODY
NORMALIZED
I = 16 mA
V = 0.4 V
V = 5 V
T = 25
q
C
F
O
CC
A
6N135, HCPL-0500
1.5
1.0
0.5
0.1
0 1 10 100
NORMALIZED CURRENT TRANSFER RATIO
I
F
- INPUT CURRENT - mA
6N136, HCPL-2502
HCPL-0501
8 PIN DIP, SO-8
F
O
CC
A
0
0 1 10 100
NORMALIZED CURRENT TRANSFER RATIO
I
F
- INPUT CURRENT - mA
1.5
0.5
1.0
NORMALIZED
I = 16 mA
V = 0.4 V
V = 4.5 V
T = 25
q
C
HCNW135/6
WIDEBODY
V
F
- FORWARD VOLTAGE - VOLTS
100
10
0.1
0.01
1.1 1.2 1.3 1.4
I
F
- FORWARD CURRENT - mA
1.61.5
1.0
0.001
1000
I
F
V
F
+T = 25
q
C
A
-
8 PIN DIP, SO-8
V
F
- FORWARD VOLTAGE - VOLTS
1000
100
10
1.0
0.1
0.01
0.001
1.2 1.3 1.4 1.5
T = 25
q
C
A
I
F
- FORWARD CURRENT - mA
I
F
V
F
+
-
1.81.71.6
WIDEBODY
Broadcom AV02-0171EN
18
6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Single-Channel, High-Speed Optocouplers
Figure 4: Current Transfer Ratio vs. Temperature
Figure 5: Propagation Delay vs. Temperature
Figure 6: Propagation Delay Time vs. Load Resistance
1.1
1.0
0.9
0.8
0.7
0.6
-60 -20 0 80
NORMALIZED CURRENT TRANSFER RATIO
T
A
- TEMPERATURE -
q
C
F
CC
A
6N135, HCPL-0500
6N136, HCPL-2502,
HCPL-0501
8 PIN DIP, SO-8
-40 20 40 60 100
O
NORMALIZED
I = 16 mA
V = 0.4 V
V = 5 V
T = 25
q
C
1.1
1.0
0.9
0.8
0.7
0.6
-60 -20 20 60
100
NORMALIZED CURRENT TRANSFER RATIO
T
A
- TEMPERATURE -
q
C
0.5
80
40
0
-40
0.4
WIDEBODY
HCNW135/6
F
CC
A
O
NORMALIZED
I = 16 mA
V = 0.4 V
V = 5 V
T = 25
q
C
2000
1500
1000
500
0
-60 -20
t
p
- PROPAGATION DELAY - ns
T
A
- TEMPERATURE - qC
8 PIN DIP, SO-8
20 60 100
6N135, HCPL-0500 (RL = 4.1 k:
6N136, HCPL-0501, HCPL-2502
IF = 16 mA, VCC = 5.0 V
tPLH tPHL
1000
800
600
400
200
0
-60 -20 0 80
T
A
- TEMPERATURE - qC
HCNW135 (R
L
= 4.1 k:
HCNW136 (R
L
= 1.9 k:
WIDEBODY
-40 20 40 60
100
I
F
= 16 mA, V
CC
= 5.0 V
t
p
- PROPAGATION DELAY - ns
tPHL
tPLH
(RL = 1.9 k:)
3.0
2.0
1.0
0.1
4
0.6
0.4
321
0.2
8765910
0.8
R
L
- LOAD RESISTANCE - (k
:
)
t
PLH
t
PHL
V = 5.0 V
T = 25
q
C
CC
I = 10 mA
I = 16 mA
F
t
P
- PROPAGATION DELAY - μs
F
A
8 PIN DIP, SO-8
R
L
-
t
P
- PROPAGATION DELAY - μs
10.0
6.0
4.0
1.0
0.1 10 40
100
0.6
0.4
4
V = 5.0 V
T = 25
q
C
A
CC
I = 10 mA
I = 16 mA
F
t
21
0.2
PLH
PHL
t
t
WIDEBODY
LOAD RESISTANCE - (k
:
)
Broadcom AV02-0171EN
19
6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Single-Channel, High-Speed Optocouplers
Figure 7: Logic High Output Current vs. Temperature
Figure 8: Small-Signal Current Transfer Ratio vs. Quiescent Input Current
Figure 9: Thermal Derating Curve, Dependence of Safety Limiting Value with Case Temperature per IEC/EN/DIN EN 60747-5-5
T
A
- TEMPERATURE -
q
C
I = 0
V = V = 5.0 V
CCO
F
-50 -25 0 +25 +50 +75 +100
10
+4
10
-2
10
-1
10
0
10
+1
10
+2
10
+3
I
OH
- LOGIC HIGH OUTPUT CURRENT - nA
-75
8 PIN DIP, SO-8
I
OH
- LOGIC HIGH OUTPUT CURRENT - nA
T
A
- TEMPERATURE -
q
C
-60 -20 0 20 40 100
10
0
10
+1
10
+2
10
+3
-40 8060
I = 0
V = V = 15 V
CCO
F
WIDEBODY
I
F
I
O
-
SMALL SIGNAL CURRENT TRANSFER RATIO
0
0.10
0.20
0.30
0
I
F
- QUIESCENT INPUT CURRENT - mA
25
16
4 8 12 20
T
A
= 25
q
C, R
L
= 100
:
, V
CC
= 5 V
8 PIN DIP, SO-8
0
0.10
0.30
0 4 8 12 16 25
0.20
0.40
20
0.50
I
F
I
O
-
SMALL SIGNAL CURRENT TRANSFER RATIO
I
F
- QUIESCENT INPUT CURRENT - mA
T
A
= 25
q
C, R
L
= 100 :, V
CC
= 5 V
WIDEBODY
OUTPUT POWER - P
S
, INPUT CURRENT - I
S
0
0
T
S
- CASE TEMPERATURE -
q
C
175
1000
50
400
12525 75 100 150
600
800
200
100
300
500
700
900 P
S
(mW)
I
S
(mA)
HCNW135/6
OUTPUT POWER - P
S
, INPUT CURRENT - I
S
0
0
T
S
- CASE TEMPERATURE -
q
C
20050
400
12525 75 100 150 175
600
800
200
100
300
500
700
P
S
(mW)
I
S
(mA) For 8-PIN DIP
I
S
(mA) For S0-8
8-PIN DIP/S0-8
Broadcom AV02-0171EN
20
6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Single-Channel, High-Speed Optocouplers
Figure 10: Frequency Response
Figure 11: Switching Test Current
Figure 12: Test Circuit for Transient Immunity and Typical Waveforms
0.1 1.0 10 100
-20
-15
-10
-5
0
+5
T
A
= 25
q
C
f - FREQUENCY - MHz
NORMALIZED RESPONSE - dB
6N135/6, HCPL-0500/1, HCPL-2502
7
1
2
3
45
6
8
+12 V
0.1 μF
V
FF
47 μF
51
:
2.1 K
:
100
:
1 K
:
1N4150 22
:
R
T
Q
1
TRIM FOR
UNITY GAIN
1.2 K
:
15 K
:
9.1 K
:
0.1 μF
100
:
Q
2
Q
3
470
:
+12 V
0.1 μF
(1 M
:
12 pF
TEST INPUT)
p-p
TYPICAL LINEARITY = ± 3% AT V = 1 V
TYPICAL SNR = 50dB
TYPICAL R = 375
:
TYPICAL V dc = 3.8 V
TYPICAL I = 9 mA
IN
T
O
F
123
Q , Q , Q : 2N3904
V
O
6N135/6, HCPL-0500/1, HCPL-2502
V
O
PULSE
GEN.
Z = 50 :
t = 5 ns
O
r
I MONITOR
F
I
F
0.1μF
L
R
C
L
= 1.5 μF
R
M
0
t
PHL
t
PLH
O
V
I
F
OL
V
1.5 V
+5 V
1
2
3
4
8
7
6
5
1.5 V
5 V
10% DUTY CYCLE
1/f < 100 μS
O
V5 V
OL
V
O
V
0 V 10% 90% 90% 10%
SWITCH AT A: I = 0 mA
F
SWITCH AT B: I = 16 mA
F
CM
V
trtf
7
1
2
3
45
6
8
V
O
0.1 μF
L
R
+5 V
PULSE GEN.
V
CM
+-
V
IF
A
B
FF
Broadcom, the pulse logo, Connecting everything, Avago Technologies, Avago, and the A logo are among the trademarks
of Broadcom and/or its affiliates in the United States, certain other countries, and/or the EU.
Copyright © 2014–2019 Broadcom. All Rights Reserved.
The term “Broadcom” refers to Broadcom Inc. and/or its subsidiaries. For more information, please visit www.broadcom.com.
Broadcom reserves the right to make changes without further notice to any products or data herein to improve reliability,
function, or design. Information furnished by Broadcom is believed to be accurate and reliable. However, Broadcom does
not assume any liability arising out of the application or use of this information, nor the application or use of any product or
circuit described herein, neither does it convey any license under its patent rights nor the rights of others.
Broadcom AV02-0171EN
22
6N135/6, HCNW135/6, HCPL-2502/0500/0501 Data Sheet Single-Channel, High-Speed Optocouplers