FTSH-1XX-XX-XXX-DV-XXX REVISION EC NOTES: No OF POSITIONS 1. C REPRESENTS A CRITICAL DIMENSION. -02 THRU -50 2. PARTS MAY BE CUT TO POSITION. (PER ROW) 3. MAXIMUM CUT FLASH: .010 [0.25] 4. MINIMUM PUSHOUT FORCE: 1.0 LB. LEAD STYLE 5. MEASURED AT BEND RADIUS, NOT AT END OF PIN. 6. TUBE ONLY -04 THROUGH -50 POSITIONS (SEE TABLE 2). -01: .120 [3.05] 7. SHEAR TAILS TO DIMENSION SHOWN. -02: .075 [1.91] 8. MAXIMUM BURR ALLOWANCE: .003 [0.08] -03: .065 [1.65] 9. GOLD PLATING TO BE ON POST, TIN PLATING TO BE ON TAIL. -04: .150 [3.81] 10. FILL WITH ALIGNMENT PIN HOLES TO TAIL SIDE. -05 .170 [4.32] 11. DUE TO THE HIGH AMOUNT OF INSERTION FORCE NEEDED, LOCKING CLIPS -14: .150 [3.81] ARE NOT COMPATIBLE WITH AUTO PLACEMENT. SAMTEC RECOMMENDS (NOT AVAILABLE WITH MANUAL PLACEMENT FOR ALL ASSEMBLIES WITH LOCKING CLIPS. -SM, FM, LM PLATING OPTIONS) DO NOT SCALE FROM THIS PRINT No OF POS x .0500+-..000150 [ +-00..1235 ] (No OF POS x .0500[1.27]) - .0500[1.27] 02 50 .135 3.43 REF 49 01 FTSHC-50-D PLATING SPECIFICATION (VALUES GIVEN ARE IN MICRO INCHES) -L: LIGHT SELECTIVE, 10 Au / 40 MIN Ni ON CONTACT AREA, MATTE TIN ON TAIL -F: FLASH SELECTIVE, 3 Au / 40 MIN Ni ON CONTACT AREA, MATTE TIN ON TAIL -S: SELECTIVE, 30 Au / 40 MIN Ni ON CONTACT AREA, MATTE TIN ON TAIL -H: HEAVY GOLD, 30 Au / 40 Ni ON CONTACT AREA, 3 Au / 40 Ni ON TAIL -SM: HEAVY SELECTIVE GOLD, 30 Au / 40 MIN Ni ON CONTACT AREA, MATTE TIN ON TAIL -LM: LIGHT SELECTIVE GOLD, 10 Au / 40 MIN Ni ON CONTACT AREA, MATTE TIN TAIL -FM: FLASH SELECTIVE GOLD, 3 Au / 40 MIN Ni ON CONTACT AREA, MATTE TIN ON TAIL -LTL: LIGHT GOLD, 10 Au / 40 MIN Ni ON CONTACT AREA, 90 / 10 5% TIN LEAD ON TAIL TAIL OPTION -DV: DOUBLE VERTICAL (USE **FTSHC-1XX-XX-XXX-DV FOR ALL OPTIONS EXCEPT -ES, -EJ, -EJM, -EJC, -EC, -EP, -EL, -EPC, -A, THEN USE FTSH-50-D AND BUILD PER PRINT) ** = SEE FTSHC-1XX-XX-XXX-DX-XX PRINT FOR DETAILS 2 MAX SWAY (EITHER DIRECTION) .016 0.41 SQ REF (TYP) EC SEE TABLE 1 C .050.004 1.270.10 2 MAX SWAY (EITHER DIRECTION) C EC 903 "A" C .099 2.51 REF SEE NOTE 3 (2 PLCS) 5713755 / 5961339 * = NOT ENGINEERING APPROVED 2 MAX SWAY (EITHER DIRECTION) "B" CONTACT AREA (SEE NOTE 9 & TABLE 1) PATENT NUMBERS * OPTIONS -P: PICK & PLACE PAD (4 POS MIN) (SEE FIG 11, SHT 4 & TABLE 5) -TR: TAPE & REEL PACKAGING -ES: END SHROUDS (SEE FIG 6, SHT 3) (MOLDED IN 5 POS MIN; -02 & -03 LEAD STYLE ONLY) (SNAP SHROUDS 9 POS MIN; -02 & -03 LEAD STYLE ONLY) (MUST USE FTSH-50-D) -EJ: EJECTOR SHROUDS: SEE FIG 4, SHT 2) (10 POS MIN; -01 LEAD STYLE ONLY)(MUST USE FTSH-50-D) -EJM: EJECTOR SHROUDS WITH MOLDED ALIGNMENT PIN (SEE FIG 5, SHT 2; 10 POS MIN; -01 LEAD STYLE ONLY) (NOT VALID WITH -A OPTION)(MUST USE FTSH-50-D) -EJC: EJECTOR SHROUDS WITH LOCKING CLIP (SEE FIG 5, SHT 2 & NOTE 11) (10 POS MIN; -01 LEAD STYLE ONLY; NOT VALID WITH -A OPTION) (MUST USE FTSH-50-D) -EC: LOCKING CLIP (SEE FIG 7, SHT 3 & NOTE 11) (9 POS MIN; -02 & -03 LEAD STYLE ONLY)(MUST USE FTSH-50-D) -EP: GUIDE POST (SEE FIG 8, SHT 3; 9 POS MIN; -02 & -03 LEAD STYLE ONLY) (USE ONLY WHEN MATING WITH CLP)(MUST USE FTSH-50-D) -EL: BOARD LOCK (SEE FIG 9, SHT 3) (9 POS MIN; -02 & -03 LEAD STYLE ONLY) (USE ONLY WHEN MATING WITH CLP)(MUST USE FTSH-50-D) -EPC: GUIDE POST & LOCKING CLIP (SEE FIG 10, SHT 3 & NOTE 11; USE ONLY WHEN MATING WITH CLP) (9 POS MIN; -02 & -03 LEAD STYLE ONLY; NOT VALID WITH -A OPTION)(MUST USE FTSH-50-D) -A: ALIGNMENT PIN (MOLDED OR STAKED; SEE FIG 3, SHT 2) (MOLDED: 3 POS MIN; STAKED: 6 POS MIN) (SAMTEC DISCRETION ON WHICH -A PIN USED) (MUST USE FTSH-50-D) -K: KEYING OPTION FOR MATING WITH FFSD (SEE TABLE 3, SHT 2; 05 THRU 25 AVAILABLE AS STANDARD) (POSITION 13, 17, 20 & 25 AVAILABLE WITH -EJ OPTION) (LEAD STYLE -01 ONLY, SEE FIG 2, SHT 2) (ALIGNMENT PIN AVAILABLE WITH -K OPTION BUT MUST BE MOLDED) (MUST USE FTSH-XX-CN-XX) -M: METAL PICK & PLACE PAD (5 POS MIN; USE MPP-22-5) (SEE FIG 12, SHT 4; NOT AVAILABLE WITH -K OPTION) .115 2.92 (SEE NOTE 5) .004[.10] SEE NOTE 8 FIG 1 FTSH-1XX-XX-XXX-DV SHOWN (SEE FTSHC-1XX-XX-XXX-DX-XX PRINT FOR DETAILS) UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN INCHES. TOLERANCES ARE: DECIMALS ANGLES .XX: .01 [.3] 1 .XXX: .005 [.13] .XXXX: .0010 [.025] MATERIAL: .23 5.8 (SEE NOTE 7) PROPRIETARY NOTE THIS DOCUMENT CONTAINS INFORMATION CONFIDENTIAL AND PROPRIETARY TO SAMTEC, INC. AND SHALL NOT BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR DISCLOSED TO OTHERS OR USED FOR ANY PURPOSE OTHER THAN THAT WHICH IT WAS OBTAINED WITHOUT THE EXPRESSED WRITTEN CONSENT OF SAMTEC, INC. DO NOT SCALE DRAWING INSULATOR: LCP UL 94 VO TERMINAL: PHOSPHOR BRONZE F:\DWG\MISC\MKTG\FTSH-1XX-XX-XXX-DV-XXX-MKT.SLDDRW SHEET SCALE: 5:1 520 PARK EAST BLVD, NEW ALBANY, IN 47150 PHONE: 812-944-6733 FAX: 812-948-5047 code 55322 e-Mail info@SAMTEC.com DESCRIPTION: .050 x .050 CL DOUBLE VERTICAL SMT TERMINAL STRIP DWG. NO. FTSH-1XX-XX-XXX-DV-XXX BY: PURVIS 10/12/1995 SHEET 1 OF 5 FIG 4 SCALE 2 : 1 FIG 2 REVISION EC -K OPTION (LEAD STYLE -01 ONLY) (DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1) (POSITION 13, 17, 20 & 25 AVAILABLE WITH -EJ OPTION) -EJ OPTION (DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1) (-01 LEAD STYLE ONLY) USE SUB-FTSH-EJEHA (2 REQ'D PER ASSEMBLY, EACH USES 1 EHA-02 & 1 FTSH-EJ) ((No OF POS x .0500[1.270]) - .003[.08]).006[0.15] .135 3.43 REF .222 5.65 REF .440 11.18 REF .200 5.08 REF .085 2.16 REF CL (No OF POS x .050[1.27])+.621[15.77] .010[0.25] .200 5.08 REF (No OF POS x .050[1.27])+.772[19.61] REF .126 3.20 REF +.005 FTSH-50-D +0.13 .115 - .000 2.92 0.00 (SEE NOTE 5) .392 9.96 REF FTSH-50-CN-XX -EJ OPTION (SHROUDS OPEN) FIG 3 FIG 5 SCALE 2 : 1 -A OPTION (DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1) (6 POSITION MINIMUM FOR STAKED ALIGNMENT PINS) (3 POSITION MINIMUM FOR MOLDED ALIGNMENT PINS) CL FTSH-50-D (SEE NOTE 10) -EJC & -EJM OPTIONS (DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 4) (-01 LEAD STYLE ONLY) CL .034 0.86 (No OF POS - 2) x .050[1.27] C SM-A9H .076 1.93 REF USE SUB-FTSH-EJEHA-A (2 REQ'D PER ASSEMBLY, EACH USES 1 EHA-02 & 1 FTSH-EJ-A) USE SUB-FTSH-EJEHA (2 REQ'D PER ASSEMBLY, EACH USES 1 EHA-02 & 1 FTSH-EJ) CL C +.005 .085 - .000 .035 0.89 REF +0.13 0.00] [2.16 (STAKED ALIGNMENT PINS) -EJC CL FTSH-50-D-XX LC-05-TM .035 0.89 REF -EJM .010 0.25 REF -EJC .05 1.3 REF -EJM PROPRIETARY NOTE .034 0.86 THIS DOCUMENT CONTAINS INFORMATION CONFIDENTIAL AND PROPRIETARY TO SAMTEC, INC. AND SHALL NOT BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR DISCLOSED TO OTHERS OR USED FOR ANY PURPOSE OTHER THAN THAT WHICH IT WAS OBTAINED WITHOUT THE EXPRESSED WRITTEN CONSENT OF SAMTEC, INC. .050 1.27 REF (No OF POS - 2) x .050[1.27] FULL R .035 0.89 REF DO NOT SCALE DRAWING SHEET SCALE: 3:1 (MOLDED ALIGNMENT PINS) F:\DWG\MISC\MKTG\FTSH-1XX-XX-XXX-DV-XXX-MKT.SLDDRW 520 PARK EAST BLVD, NEW ALBANY, IN 47150 PHONE: 812-944-6733 FAX: 812-948-5047 code 55322 e-Mail info@SAMTEC.com DESCRIPTION: .050 x .050 CL DOUBLE VERTICAL SMT TERMINAL STRIP DWG. NO. FTSH-1XX-XX-XXX-DV-XXX BY: PURVIS 10/12/1995 SHEET 2 OF 5 REVISION EC FIG 6 FIG 8 -ES OPTION (DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1) (USE -02 OR -03 LEAD STYLE ONLY) (9 POS MIN FOR SNAP SHROUDS) (5 POS MIN FOR MOLDED SHROUDS) -EP OPTION (DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 6) (USE ONLY WHEN MATING WITH CLP) (No OF POS x .050[1.27])+.231[5.87].008[0.20] (No OF POS x .050[1.27])+.156[3.96] REF .265 6.73 REF .032[0.81] REF CHAMFER .075 1.91 REF 02 .188 4.78 REF .139 3.53 REF .288 7.32 REF FTSH-EP .120 3.05 REF .314 7.96 01 (No OF POS x .050[1.27])+.101[2.57].008[0.20] FIG 9 ES-FTSH .168 4.27 REF .087 2.21 REF .194 4.91 (SNAP SHROUDS) -EL OPTION (DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 6) (USE ONLY WHEN MATING WITH CLP) .125 3.18 REF FTSH-EL .293 7.44 REF FTSH-50-D (SEE NOTE 10) .319 8.09 (No OF POS x .050[1.27]) +.153[3.89] REF 02 (No OF POS x .050[1.27])+.257[6.53] .1750 4.445 REF .0960 2.438 REF FIG 10 -EPC OPTION (DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 6) (USE ONLY WHEN MATING WITH CLP) 01 (No OF POS x .050[1.27])+.231[5.87].008[0.20] FTSH-49-ES-XX-X (No OF POS x .050[1.27])+.156[3.96] REF .032[0.81] REF CHAMFER .075 1.91 REF .1775 4.509 REF .0990 2.515 REF FTSH-EP .288 7.32 REF (MOLDED SHROUDS) FIG 7 -EC OPTION (DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 6) .120 3.05 REF .314 7.96 LC-05-TM .055 1.40 (No OF POS x .050[1.27])+.079[2.01].008[.20] (No OF POS x .050[1.27])+.131[3.32].008[0.20] PROPRIETARY NOTE .280 7.11 REF .055 1.40 THIS DOCUMENT CONTAINS INFORMATION CONFIDENTIAL AND PROPRIETARY TO SAMTEC, INC. AND SHALL NOT BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR DISCLOSED TO OTHERS OR USED FOR ANY PURPOSE OTHER THAN THAT WHICH IT WAS OBTAINED WITHOUT THE EXPRESSED WRITTEN CONSENT OF SAMTEC, INC. FTSH-EC DO NOT SCALE DRAWING LC-05-TM SHEET SCALE: 2:1 (No OF POS x .050[1.27])+.079[3.30].008[0.20] F:\DWG\MISC\MKTG\FTSH-1XX-XX-XXX-DV-XXX-MKT.SLDDRW 520 PARK EAST BLVD, NEW ALBANY, IN 47150 PHONE: 812-944-6733 FAX: 812-948-5047 code 55322 e-Mail info@SAMTEC.com DESCRIPTION: .050 x .050 CL DOUBLE VERTICAL SMT TERMINAL STRIP DWG. NO. FTSH-1XX-XX-XXX-DV-XXX BY: PURVIS 10/12/1995 SHEET 3 OF 5 REVISION EC "M" .20 5.1 REF .13 3.3 REF "P" .24 6.1 REF .07 1.7 REF .20 5.1 REF .16 4.1 REF PPP-25 .13 3.3 REF PPP-48 -P "M" = No OF POSITIONS x .0500 [1.270] "P" ={("M" -200 [508]) / 2} .020 [.51] FIG 11 -P OPTION (DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1) CL .23 5.8 REF EC FTSH-50-CN-XX -K-P-TR FTSHC-50-D *MOLDED SHROUD ONLY ** USE PPP-25-NT WITH -TR PACKAGING ONLY PPP-25-NT -P-TR (DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1) (DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 2) NOTE: TAPE & REEL ORIENTATION: POLARIZATION NOTCH TO THE RIGHT .32 8.1 REF .32 8.1 REF PPP-41 .16 4.1 REF -EJ-P & -EJX -P (DIFFERENT AS SHOWN, OTHERWISE SAME AS FIGS 4 & 5) FIG 12 "M" REF TAPE & REEL VIEW *-M: METAL PICK & PLACE PAD (DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1) (NOT AVAILABLE WITH -K OPTION)(5 POS MIN) * = NOT ENGINEERING APPROVED USER DIRECTION OF UN-REELING POCKET NOT DETAILED "P" .250 6.35 REF .100 2.55 REF PROPRIETARY NOTE MPP-22-5 THIS DOCUMENT CONTAINS INFORMATION CONFIDENTIAL AND PROPRIETARY TO SAMTEC, INC. AND SHALL NOT BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR DISCLOSED TO OTHERS OR USED FOR ANY PURPOSE OTHER THAN THAT WHICH IT WAS OBTAINED WITHOUT THE EXPRESSED WRITTEN CONSENT OF SAMTEC, INC. "B" FTSHC-50-D "M" = No OF POSITIONS x .0500[1.270] "P" = {("M" - .250[6.35]) / 2} .020[0.51] F:\DWG\MISC\MKTG\FTSH-1XX-XX-XXX-DV-XXX-MKT.SLDDRW DO NOT SCALE DRAWING SHEET SCALE: 3:1 520 PARK EAST BLVD, NEW ALBANY, IN 47150 PHONE: 812-944-6733 FAX: 812-948-5047 code 55322 e-Mail info@SAMTEC.com DESCRIPTION: .050 x .050 CL DOUBLE VERTICAL SMT TERMINAL STRIP DWG. NO. FTSH-1XX-XX-XXX-DV-XXX BY: PURVIS 10/12/1995 SHEET 4 OF 5 REVISION EC FIG 13 PT-FTSH002-DV-A-P-M PT-FTSH004-DV-EX-A-P-M TUBE VIEWS PT-FTSH004-DV-EX-A-P-M PT-FTSH006-DV-EJC-K-P EC -ES , -P(-05 STYLE) (MOLDED END SHROUD ONLY) -DV (SNAP END SHROUD ONLY) -EJ, EJX AND -EJ-X PT-FTSH003-DV-EJC-K PT-FTSH007-DV-K-P PT-FTSH007-DV-K-P -ES-P, -P (SNAP END SHROUD ONLY) EC -K-P "A" - .034 0.864 -K, -K-A (FOR -01 LEAD STYLE ONLY) ALL -EJ-K OPTIONS "A" - .034 0.864 "C" REF (SEE TABLE 1) "A" - .034 0.864 .112.010 2.8450.254 (SEE NOTE 7) .050.005 1.2700.127 IN PROCESS 2 W/O A PINS IN PROCESS 1 IN PROCESS 3 W/O A PINS W/O A PINS "A" - .084 2.134 "A" -.084[2.134] "A" - .084 2.134 "C" REF (SEE TABLE 1) PROPRIETARY NOTE .175.010 4.4450.254 (SEE NOTE 7) .100.005 2.5400.127 IN PROCESS 1 WITH A PINS* IN PROCESS 2 * = ONLY FOR -01, -04, -05 AND -14 LEAD STYLES ONLY WITH A PINS* IN PROCESS 3 WITH A PINS* IN-PROCESS VIEWS ARE FOR HANDFILL ONLY F:\DWG\MISC\MKTG\FTSH-1XX-XX-XXX-DV-XXX-MKT.SLDDRW THIS DOCUMENT CONTAINS INFORMATION CONFIDENTIAL AND PROPRIETARY TO SAMTEC, INC. AND SHALL NOT BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR DISCLOSED TO OTHERS OR USED FOR ANY PURPOSE OTHER THAN THAT WHICH IT WAS OBTAINED WITHOUT THE EXPRESSED WRITTEN CONSENT OF SAMTEC, INC. DO NOT SCALE DRAWING SHEET SCALE: 2:1 520 PARK EAST BLVD, NEW ALBANY, IN 47150 PHONE: 812-944-6733 FAX: 812-948-5047 code 55322 e-Mail info@SAMTEC.com DESCRIPTION: .050 x .050 CL DOUBLE VERTICAL SMT TERMINAL STRIP DWG. NO. FTSH-1XX-XX-XXX-DV-XXX BY: PURVIS 10/12/1995 SHEET 5 OF 5