L293D QUADRUPLE HALF-H DRIVER SLRS008A - SEPTEMBER 1986 - REVISED MAY 1990 * * * * * * * * * 600-mA Output Current Capability Per Driver Pulsed Current 1.2-A Per Driver Output Clamp Diodes for Inductive Transient Suppression Wide Supply Voltage Range 4.5 V to 36 V Separate Input-Logic Supply Thermal Shutdown Internal ESD Protection High-Noise-Immunity Inputs Functional Replacement for SGS L293D NE PACKAGE (TOP VIEW) 1, 2EN 1A 1Y HEAT SINK AND GROUND 1 16 2 15 3 14 4 13 5 12 2Y 2A 6 11 7 10 VCC2 8 9 2 All inputs are TTL-compatible. Each output is a complete totem-pole drive circuit with a Darlington transistor sink and a pseudo-Darlington source. Drivers are enabled in pairs with drivers 1 and 2 enabled by 1, 2EN and drivers 3 and 4 enabled by 3, 4EN. When an enable input is high, the associated drivers are enabled, and their outputs are active and in phase with their inputs. External high-speed output clamp diodes should be used for inductive transient suppression. When the enable input is low, those drivers are disabled, and their outputs are off and in a high-impedance state. With the proper data inputs, each pair of drivers form a full-H (or bridge) reversible drive suitable for solenoid or motor applications. EN EN 7 2A 6 10 3A 11 9 3, 4EN EN EN 15 4A 14 1Y 2Y 3Y 4Y This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. logic diagram 1A 2 3 1Y 1 1, 2EN 2A 3A 7 6 10 11 2Y 3Y 9 3, 4EN 4A 14 15 4Y FUNCTION TABLE (each driver) A VCC1 terminal, separate from VCC2, is provided for the logic inputs to minimize device power dissipation. The L293D is designed for operation from 0C to 70C. 3 1 1, 2EN The L293D is a quadruple high-current half-H driver designed to provide bidirectional drive currents of up to 600-mA at voltages from 4.5 V to 36 V. It is designed to drive inductive loads such as relays, solenoids, dc and bipolar stepping motors, as well as other high-current/high-voltage loads in positive-supply applications. 3Y 3A 3, 4EN logic symbol 1A description VCC1 4A 4Y HEAT SINK AND GROUND INPUTS A EN OUTPUT Y H L X H H L H L Z H = high-level, L = low level, X = irrelevant, Z = high-impedance (off) In the thermal shutdown mode, the output is in the high-impedance state regardless of the input levels. Copyright 1990, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 3-1 L293D QUADRUPLE HALF-H DRIVER SLRS008A - SEPTEMBER 1986 - REVISED MAY 1990 schematics of inputs and outputs EQUIVALENT OF EACH INPUT TYPICAL OF ALL OUTPUTS VCC2 VCC1 Current Source Output Input GND GND absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Logic supply voltage range, VCC1 (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 V Output supply voltage range, VCC2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 V Input voltage range, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Output voltage range, VO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 3 V to VCC2 + 3 V Peak output current (nonrepetitive, t 100 s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2 A Continuous output current, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 600 mA Continuous total dissipation at (or below) 25C free-air temperature (see Notes 2 and 3) . . . . . . . 2075 mW Continuous total dissipation at 80C case temperature (see Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . 5000 mW Operating case or virtual junction temperature range, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 40C to 150C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65C to 150C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260C NOTES: 1. All voltage values are with respect to the network ground terminal. 2. For operation above 25C free-air temperature, derate linearly at the rate of 16.6 mW/C. 3. For operation above 25C case temperature, derate linearly at the rate of 71.4 mW/C. Due to variations in individual device electrical characteristics and thermal resistance, the built-in thermal overload protection may be activated at power levels slightly above or below the rated dissipation. recommended operating conditions MIN Logic supply voltage, VCC1 Output supply voltage, VCC2 High level input voltage, High-level voltage VIH VCC1 7 V VCC1 7 V Low-level input voltage, VIL MAX UNIT 4.5 7 V VCC1 2.3 36 V 2.3 VCC1 7 V - 0.3 1.5 V Operating free-air temperature, TA 0 70 C The algebraic convention, in which the least positive (most negative) value is designated minimum, is used in this data sheet for logic voltage levels. 3-2 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 L293D QUADRUPLE HALF-H DRIVER SLRS008A - SEPTEMBER 1986 - REVISED MAY 1990 electrical characteristics, VCC1 = 5 V, VCC2 = 24 V, TA = 25C PARAMETER TEST CONDITIONS VOH VOL High-level output voltage VOKH VOKL High-level output clamp voltage Low-level output voltage High level input current High-level IIL Low level input current Low-level ICC1 TYP VCC2 - 1.8 A EN A EN Logic supply current Output supply current IO = 0 V 1.8 V V V 0.2 100 0.2 10 -3 - 10 -2 - 100 All outputs at high level 13 22 All outputs at low level 35 60 8 24 All outputs at high level 14 24 All outputs at low level 2 6 All outputs at high impedance 2 4 VI = 0 All outputs at high impedance ICC2 UNIT VCC2 + 1.3 1.3 VI = 7 V IO = 0 MAX VCC2 - 1.4 1.2 IOK = - 0.6 A IOK = - 0.6 A Low-level output clamp voltage IIH MIN IOH = - 0.6 A IOL = 0.6 A A A mA mA switching characteristics, VCC1 = 5 V, VCC2 = 24 V, TA = 25C PARAMETER TEST CONDITIONS MIN TYP MAX UNIT tPLH tPHL Propagation delay time, low-to-high-level output from A input 800 ns Propagation delay time, high-to-low-level output from A input 400 ns tTLH tTHL Transition time, low-to-high-level output 300 ns 300 ns CL = 30 pF, pF See Figure 1 Transition time, high-to-low-level output PARAMETER MEASUREMENT INFORMATION tf tr 90% Input 5V 24 V Input 1.5 V 1.5 V 10% Pulse Generator (see Note A) 3V 90% 10% 0 VCC1 VCC2 tw A Y tPHL Output tPLH V 90% OH 90% 3V CL = 30 pF (see Note B) EN GND 50% Output 10% 50% 10% tTHL TEST CIRCUIT VOL tTLH VOLTAGE WAVEFORMS NOTES: A. The pulse generator has the following characteristics: tr 10 ns, tf 10 ns, tw = 10 s, PRR = 5 kHz, ZO = 50 . B. CL includes probe and jig capacitance. Figure 1. Test Circuit and Voltage Waveforms POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 3-3 L293D QUADRUPLE HALF-H DRIVER SLRS008A - SEPTEMBER 1986 - REVISED MAY 1990 APPLICATION INFORMATION 5V 24 V VCC1 10 k VCC2 3 16 1,2EN 1 Control A 1Y 1A 2 3 Motor 2A 2Y 7 6 3,4EN 9 Control B 3A 10 3Y 4A 15 4Y 11 14 Thermal Shutdown 4, 5, 12, 13 GND Figure 2. Two-Phase Motor Driver 3-4 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE ("CRITICAL APPLICATIONS"). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER'S RISK. In order to minimize risks associated with the customer's applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI's publication of information regarding any third party's products or services does not constitute TI's approval, warranty or endorsement thereof. Copyright 1998, Texas Instruments Incorporated