Altera Corporation 1
In-System Pr ogrammability
in MAX Devices
June 2000, ver. 1.03 Application Note 95
A-AN-095-01.02
®
Introduction
MAX
®
devices are programmable logic devices (PLDs), based on the
Altera
®
Multiple Array MatriX (MAX) architecture that and supports the
IEEE Std. 1149.1 Joint Test Action Group (JTAG) interface. MAX devices
are also in-system programmable, which adds programming flexibility
and provides benefits in many phases of product development,
manufacturing, and field use. This application note provides background
information on in-system programmability (ISP) and the IEEE Std. 1149.1
JTAG interface and discusses the advantages of using ISP-capable MAX
devices.
Features &
Benefits
In-system design, prototyping, and manufacturing, reduces cost, shortens
development time, and provides a wider range of programming options
than standard device programming methods. With ISP, you can:
■
Program and reprogram devices after they are soldered onto the
printed circuit board (PCB), minimizing the possibility of lead
damage or electrostatic discharge (ESD) exposure.
■
Manufacture systems before you finalize device configuration.
■
Perform boundary-scan test (BST) procedures and program devices
using in-circuit testers.
■
Upgrade systems in the field after they have been shipped.
2 Altera Corporation
AN 95: In-System Programmability in MAX Devices
Table 1 describes the features and benefits of using ISP-capable
MAX devices.
V
CC
-Level
Programming
ISP-capable MAX devices support ISP through a V
CC
-level programming
voltage. The devices generate a 12.0-V programming voltage internally to
program, verify, and erase the device’s EEPROM cells, eliminating the
need for the external 12.0-V programming voltage typically required for
programming.
ISP-capable MAX devices are guaranteed for 100 erase and programming
cycles with 100
%
programming and functional yields.
Table 1. ISP-Capable MAX Device Features & Benefits
Product Development
Phase
Features Benefits
Device prototyping Devices are programmed with a V
CC
-level
programming voltage. Eliminates the need for a 12.0-V
programming voltage and the possibility of
accidental damage to lower voltage parts.
Also reduces system power requirements.
Devices can be programmed while
soldered to a PCB. Minimizes device handling, thereby
protecting devices from ESD and lead
damage.
Prototype systems can be assembled
before the device configuration is
finalized.
Cuts prototype development time and saves
development costs.
System manufacturing PLDs can be treated the same way as
other board-level devices because they
can be programmed after the PCB is
assembled.
Simplifies manufacturing, saves time, and
protects devices from ESD and lead
damage.
ISP is implemented using the IEEE Std.
1149.1 (JTAG) interface; therefore, circuit
testing and device programming can be
combined into a single manufacturing step
using a standard in-circuit tester.
Programming data can be downloaded
from in-circuit testers, PCs, or
workstations during final PCB test.
Devices can be programmed with test
configurations. Enhances design debugging and board-
level testing capabilities.
In-field programming Devices can be reprogrammed in the field. Adds versatility and reduces service costs,
thereby making products more attractive to
the consumer.
Altera Corporation 3
AN 95: In-System Programmability in MAX Devices
Programming
Systems
In Altera devices, ISP is implemented using the IEEE Std.1149.1 JTAG
interface, which streamlines PCB testing and device programming
operations into a single manufacturing step.
ISP-capable MAX devices are supported by the following systems:
■
MAX+PLUS
II development system
■
In-circuit testers
■
Embedded processors
MAX+PLUS II Development System
You can use a PC or UNIX workstation, the MAX+PLUS II Programmer,
and the BitBlaster
™
serial or ByteBlasterMV
™
parallel port download cable
to download Programmer Object Files (
.pof
), Jam Files (
.jam
), or
Jam
™
Byte-Code Files (
.jbc
)from the MAX+PLUS II software to ISP-
capable MAX devices mounted on a PCB. This method is more cost-
effective than other programming methods because design, simulation,
and prototyping can be performed using the same PC- or UNIX
workstation-based system.
For production, you can implement ISP using Altera’s free stand-alone
programming software and the BitBlasterMV cable to download POFs.
1
PC-based stand-alone programming software,
asap2.exe
, is
available from Altera’s FTP site at
ftp.altera.com
in the
\pub\misc
directory.
Figure 1 shows the 10-pin female plug dimensions for the BitBlaster or
ByteBlaster download cable.
4 Altera Corporation
AN 95: In-System Programmability in MAX Devices
Figure 1. 10-Pin Female Plug Dimensions
Dimensions are shown in inches. The spacing between pin centers is 0.1 inch.
Table 2 identifies the 10-pin female plug’s pin names for the
corresponding download mode.
1
The circuit board must supply V
CC
and ground to the
ByteBlaster cable.
0.250 Typ.
0.700 Typ.
0.425 Typ.
0.100 Sq.
1
2
3
4
5
6
7
8
9
10
0.025 Sq.
Color Strip
Table 2. Female Plug’s Pin Names & Download Modes
Pin JTAG Mode PS Mode
Signal Name Description Signal Name Description
1
TCK
Clock signal
DCLK
Clock signal
2
GND
Signal ground
GND
Signal ground
3
TDO
Data from device
CONFIG_DONE
Configuration
control
4
VCC
Power supply
VCC
Power supply
5
TMS
JTAG state
machine control
nCONFIG
Configuration
control
6 – No connect – No connect
7 – No connect
nSTATUS
Configuration
status
8 – No connect – No connect
9
TDI
Data to device
DATA0
Data to device
10
GND
Signal ground
GND
Signal ground
Altera Corporation 5
AN 95: In-System Programmability in MAX Devices
ISP-capable devices are programmed via a device’s JTAG pins:
TCK
,
TMS
,
TDI
,
and
TDO
. Figure 2 shows how the BitBlaster or ByteBlaster download
cable interfaces with an ISP-capable device. The I/O pins are tri-stated
during in-system programming.
Figure 2. ISP-Capable MAX Device Programming with the BitBlaster or
ByteBlaster Download Cable
f
Search for “Programming a Single Device with the BitBlaster or
ByteBlaster” in MAX+PLUS II Help, or go to the
BitBlaster Serial Download
Cable Data Sheet
and
ByteBlaster Parallel Port Download Cable Data Sheet
in
this handbook for more information.
In-Circuit Test Programming
You can program ISP-capable MAX devices during the final PCB testing
stage using in-circuit testers and the IEEE Std. 1149.1 (JTAG) interface. To
program a device using in-circuit testers, create a Jam or SVF File with the
MAX+PLUS II software and download this file from an in-circuit test
station to one or more ISP-capable MAX devices.
f
Go to
Product Information Bulletin 27 (Jam Programming and Test Language
Overview)
and
the
Jam Programming
and
Test Language Specification
, version
1.1 in this handbook for more information on Jam Files.
Target Altera Device
GND
10-Pin Male
Header (Top View)
Pin 1
VCC
GND
TCK
TDO
TMS
TDI
Ω
VCC
1 k
VCC
1 kΩ
1 kΩ
GND
6 Altera Corporation
AN 95: In-System Programmability in MAX Devices
Embedded Processor Programming
You can program ISP-capable MAX devices in-system using an
embedded processor. For example, programming information can be
stored in an EPROM and shifted into the ISP-capable MAX device using a
4-bit interface from the processor to the device’s JTAG pins. This method
lets you program devices during burn-in and upgrade devices in the field.
You can program MAX devices with an embedded processor by creating
a Jam File from the MAX+PLUS II software and downloading it with the
Jam Player.
f
Go to
Application Note 88 (Using the Jam Language for ISP & ICR via an
Embedded Processor)
for more information on embedded processor
programming. Go to
Product Information Bulletin 27 (Jam Programming and
Test Language Overview)
and
the
Jam Programming
and
Test Language
Specification
, version 1.1 in this handbook for more information on the Jam
Player.
IEEE Std.
1149.1
Interface
MAX device JTAG pins and functions are described in Table 3.
Table 3. JTAG Pins
Pin Description Function
TDI
Test data input Serial input pin for data and instructions, which are
shifted in on the rising edge of
TCK
. This signal needs
to be externally pulled high during normal operation.
TDO
Test data output Serial data output pin for instructions and data. Data is
shifted out on the falling edge of
TCK
. This signal is
tri-stated if data is not being shifted out of the device.
TMS
Test mode select Input pin controls the IEEE Std. 1149.1 JTAG state
machine and is evaluated on the rising edge of
TCK.
This signal needs to be externally pulled high during
normal operation.
TCK Test clock Provides the clock signal for the JTAG circuits. The
maximum operating frequency is 10 MHz. This signal
needs to be externally pulled low during normal
operation.
Altera Corporation 7
AN 95: In-System Programmability in MAX Devices
During erasure, programming, and verification, all device I/O pins are
tri-stated to eliminate interference from other devices on the PCB.
Devices are programmed by applying the appropriate signals on the TMS
and TCK inputs and shifting data into and out of the devices on the TDI
and TDO pins, respectively. After programming, the IEEE Std. 1149.1
JTAG Test Access Port (TAP) controller state machine must be advanced
to the RESET state, which is maintained by external pull-up resistors on
the TCK, TMS, and TDI pins. During normal operation, the pull-up
resistors prevent the device from entering other modes.
Figure 3 shows the timing waveforms for the IEEE Std. 1149.1 JTAG TAP
controller state machine.
Figure 3. JTAG Waveforms for MAX Devices
TDO
TCK
tJPZX tJPCO
tJPH
tJPXZ
tJCP
tJPSU
tJCL
tJCH
TDI
TMS
Signal
to Be
Captured
Signal
to Be
Driven
tJSZX
tJSSU tJSH
tJSCO tJSXZ
8 Altera Corporation
AN 95: In-System Programmability in MAX Devices
Table 4 shows the JTAG timing parameters and values for ISP-capable
MAX devices.
fGo to Application Note 39 (IEEE Std.1149.1 (JTAG) Boundary-Scan Testing in
Altera Devices) for information on the IEEE Std.1149.1 JTAG TAP
controller state machine.
Programming
ISP-Capable
MAX Devices
You can use an IEEE Std.1149.1 JTAG-compatible header to program a
single device or a chain of devices, depending on the layout of your PCB.
Single-Device Programming
For PCBs that contain a single ISP-capable MAX device, a
JTAG-compatible header—such as the 10-pin BitBlaster or ByteBlaster
header—can be used to program the device. See Figure 4.
Table 4. JTAG Timing Parameters & Values for MAX Devices
Symbol Parameter Min Max Unit
tJCP TCK clock period 100 ns
tJCH TCK clock high time 50 ns
tJCL TCK clock low time 50 ns
tJPSU JTAG port setup time 20 ns
tJPH JTAG port hold time 45 ns
tJPCO JTAG port clock to output 25 ns
tJPZX JTAG port high impedance to valid output 25 ns
tJPXZ JTAG port valid output to high impedance 25 ns
tJSSU Capture register setup time 20 ns
tJSH Capture register hold time 45 ns
tJSCO Update register clock to output 25 ns
tJSZX Update register high impedance to valid output 25 ns
tJSXZ Update register valid output to high impedance 25 ns
Altera Corporation 9
AN 95: In-System Programmability in MAX Devices
Figure 4. Single-Device Programming
JTAG-Chain Device Programming
When programming a chain of devices, one JTAG-compatible plug, such
as a BitBlaster or ByteBlaster 10-pin male plug, is connected to several
devices. The number of devices in the JTAG chain is limited only by the
drive capability of the BitBlaster or ByteBlaster download cable.
However, when three or more devices are connected in a JTAG chain,
Altera recommends buffering the TDO,TCK, TDI, and TMS pins.
JTAG-chain device programming is ideal when the circuit board contains
multiple devices, or when the circuit board is tested using JTAG BST. See
Figure 5.
TDI TDO
TMS TCK
TDI
TCK
TMS
TDO
IS P Tar g et De vi ce
1 kΩ
1 kΩ
VCC
VCC
1 kΩ
IEEE Std. 1149.1
JTAG Interface
10 Altera Corporation
AN 95: In-System Programmability in MAX Devices
Figure 5. JTAG-Chain Device Programming with a BitBlaster or ByteBlaster Cable
To program a single ISP-capable MAX device in a JTAG chain, the
programming software puts all other devices in the JTAG chain in
BYPASS mode. When in BYPASS mode, devices pass programming data
from the TDI pin to the TDO pin through a single bypass register.
Bypassed devices are not affected internally, thereby enabling the
programming software to erase, program, or verify the target device.
fGo to Application Note 39 (IEEE 1149.1 (JTAG) Boundary-Scan Testing in
Altera Devices) for more information on the BYPASS mode.
Conclusion ISP-capable MAX devices offer benefits in product design, prototyping,
and manufacturing. ISP simplifies the manufacturing flow by allowing
the devices to be mounted on a PCB with standard pick-and-place
equipment before they are programmed. ISP-capable MAX devices can
be programmed by downloading the information via in-circuit testers,
embedded processors, or the BitBlaster or ByteBlaster download cables.
In addition, programming these devices after they are placed on the
board eliminates lead damage on high pin-count packages, e.g., quad flat
pack (QFP) packages, due to device handling. These devices can also be
reprogrammed in the field (i.e., product upgrades can be performed in
the field via software or modem).
Other IEEE Std.
1149.1 JTAG-
Compliant Device
Other IEEE Std.
1149.1 JTAG-
Compliant Device
TMS TCK
TDI TDO
TMS TCK
Target
Altera Device
TDI TDO
ByteBlaster
10-Pin Male Header
TDI TDO
TMS TCK
1 kΩ
VCC
1 kΩ
VCC
1 kΩ
Altera, MAX, MAX+PLUS, MAX+PLUS II, FLEX, FLEX 10K, FLEX 10KA, FLEX 8000, FLEX 8000A, FLEX 6000,
MAX 9000, MAX 9000A, MAX 7000, MAX 7000S, MAX 7000A, EPF10K10, EPF10K10A, EPF10K20, EPF10K30,
EPF10K30A, EPF10K40, EPF10K50, EPF10K50V, EPF10K70, EPF10K100, EPF10K100A, EPF8282A,
EPF8282AV, EPF8820A, EPM9320, EPM9320A, EPM9400, EPM9480, EPM9480A, EPM9560, EPM9560A,
EPM7032S, EPM7064S, EPM7064A, EPM7128S, EPM7128A, EPM7160S, EPM7192S, EPM7256S, EPM7256A,
EPM7384A, EPM7512A, and EPM71024A are trademarks and/or service service marks of Altera Corporation
in the United States and other countries. Altera acknowledges the trademarks of other organizations for their
respective products or services mentioned in this document. Altera products are protected under numerous
U.S. and foreign patents and pending applications, maskwork rights, and copyrights. Altera warrants
performance of its semiconductor products to current specifications in accordance with Altera’s standard
warranty, but reserves the right to make changes to any products and services at any time without notice.
Altera assumes no responsibility or liability arising out of the application or use of any
information, product, or service described herein except as expressly agreed to in writing
by Altera Corporation. Altera customers are advised to obtain the latest version of device
specifications before relying on any published information and before placing orders for
products or services.
Copyright 2000Altera Corporation. All rights reserved.
101 Innovation Drive
San Jose, CA 95134
(408) 544-7000
http://www.altera.com
Applications Hotline:
(800) 800-EPLD
Customer Marketing:
(408) 544-7104
Literature Services:
(408) 544-7144
lit_req@altera.com
®
AN 95: In-System Programmability in MAX Devices
11 Altera Corporation
Printed on Recycled Paper.
Revision
History
The information contained in Application Note 95 (In-System
Programmability in MAX Devices) version 1.03 supersedes information
published in previous versions.
Version 1.03 Changes
Application Note 95 (In-System Programmability in MAX Devices) version
1.03 contains the following changes:
■Corrected information in the “In-Circuit Test Programming” on
page 5.
Version 1.02 Changes
Application Note 95 (In-System Programmability in MAX Devices) version
1.02 contains the following changes:
■Corrected TCK information in Table 2.
■Corrected Figure 2.
Version 1.01 Changes
Application Note 95 (In-System Programmability in MAX Devices) version
1.01 contained the following changes:
■Corrected information on the number of devices connected in a
JTAG chain in “JTAG-Chain Device Programming” on page 9.
■Made minor illustrative, textual, and style changes.
