SN75177B, SN75178B DIFFERENTIAL BUS REPEATERS SLLS002C - D2606, JULY 1985 - REVISED FEBRUARY 1993 * * * * * * * * * * * * SN75177B . . . D OR P PACKAGE (TOP VIEW) Meets EIA Standards RS-422-A and RS-485 and CCITT Recommendations V.11 and X.27 Designed for Multipoint Transmission on Long Bus Lines in Noisy Environments 3-State Outputs Bus Voltage Range . . . - 7 V to 12 V Positive and Negative Current Limiting Driver Output Capability . . . 60 mA Max Driver Thermal Shutdown Protection Receiver Input Impedance . . . 12 k Min Receiver Input Sensitivity . . . 200 mV Receiver Input Hysteresis . . . 50 mV Typ Operates From Single 5-V Supply Low Power Requirements VCC T EN GND 1 8 2 7 3 6 4 5 A B Z Y SN75178B . . . P PACKAGE (TOP VIEW) VCC T EN GND 1 8 2 7 3 6 4 5 A B Z Y THE SN75177B IS NOT RECOMMENDED FOR NEW DESIGN description The SN75177B and SN75178B differential bus repeaters are monolithic integrated devices each designed for one-way data communication on multipoint bus transmission lines. These devices are designed for balanced transmission bus line applications and meet EIA Standard RS-422-A and RS-485 and CCITT Recommendations V.11 and X.27. Each device is designed to improve the performance of the data communication over long bus lines. The SN75177B and SN75178B are identical except for the complementary enable inputs, which allow the devices to be used in pairs for bidirectional communication. The SN75177B and SN75178B feature positive- and negative-current limiting 3-state outputs for the receiver and driver. The receiver features high input impedance, input hysteresis for increased noise immunity, and input sensitivity of 200 mV over a common-mode input voltage range of - 7 V to 12 V. The driver features thermal shutdown for protection from line fault conditions. Thermal shutdown is designed to occur at a junction temperature of approximately 150C. The driver is designed to drive current loads up to 60 mA maximum. The SN75177B and SN75178B are designed for optimum performance when used on transmission buses employing the SN75172 and SN75174 differential line drivers, SN75173 and SN75175 differential line receivers, or SN75176B bus transceiver. Function Tables SN75177B DIFFERENTIAL INPUTS ENABLE A-B EN T OUTPUTS Y Z VID 0.2 V - 0.2 V < VID < 0.2 V H H H L H ? ? ? VID 0.2 V X H L L H L Z Z Z SN75178B DIFFERENTIAL INPUTS ENABLE A-B EN T OUTPUTS Y Z VID 0.2 V - 0.2 V < VID < 0.2 V L H H L L ? ? ? VID 0.2 V X L L L H H Z Z Z H = high level, L = low level, ? = indeterminate, X = irrelevant, Z = impedance (off) Copyright 1993, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 2-1 SN75177B, SN75178B DIFFERENTIAL BUS REPEATERS SLLS002C - D2606, JULY 1985 - REVISED FEBRUARY 1993 logic symbols logic diagrams (positive logic) SN75177B SN75177B EN A B T 3 8 EN EN 5 6 7 2 A Y B Z T A B T 3 8 8 5 7 6 2 Receiver EN EN 5 7 6 2 A Y B Z T 3 8 5 7 6 2 Receiver Driver schematics of inputs and outputs EQUIVALENT OF EACH INPUT TYPICAL OF ALL DRIVER OUTPUTS VCC VCC Req Input Output Driver input: Req = 3 k NOM GND Enable inputs: Req = 8 k NOM EQUIVALENT OF EACH RECEIVER INPUT TYPICAL OF RECEIVER OUTPUT VCC 85 NOM VCC 960 NOM 16.8 k 960 NOM NOM 2-2 Z Driver These symbols are in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. Input Y SN75178B SN75178B EN 3 Output POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 Y Z SN75177B, SN75178B DIFFERENTIAL BUS REPEATERS SLLS002C - D2606, JULY 1985 - REVISED FEBRUARY 1993 absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Voltage range at any bus terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 10 V to 15 V Differential input voltage (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 V Enable input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V Continuous total dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table Operating free-air temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0C to 70C Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65C to 150C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260C NOTES: 1. All voltage values, except differential input voltage, are with respect to network ground terminal. 2. Differential input voltage is measured at the noninverting input with respect to the corresponding inverting input. DISSIPATION RATING TABLE TA 25C POWER RATING DERATING FACTOR ABOVE TA = 25C TA = 70C POWER RATING D 725 mW 5.8 mW/C 464 mW P 1000 mW 8.0 mW/C 640 mW PACKAGE recommended operating conditions Supply voltage, VCC High-level input voltage, VIH EN or EN low-level input voltage, VIL EN or EN MAX UNIT 5 5.25 V - 7 Differential input voltage, VID Low level output current, Low-level current IOL NOM 2 Common-mode input voltage, VIC High level output current, High-level current IOH MIN 4.75 Driver Receiver Driver V 0.8 V 12 V 12 V - 60 mA - 400 A 60 Receiver 8 mA Operating free-air temperature, TA 0 70 C The algebraic convention, where the less-positive (more-negative) limit is designated minimum, is used in this data sheet for common-mode input voltage and threshold voltage. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 2-3 SN75177B, SN75178B DIFFERENTIAL BUS REPEATERS SLLS002C - D2606, JULY 1985 - REVISED FEBRUARY 1993 DRIVER SECTION electrical characteristics over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) PARAMETER TEST CONDITIONS VIK VO Input clamp voltage Output voltage II = - 18 mA IO = 0 |VOD1| Differential output voltage IO = 0 |VOD2| Differential output voltage |VOD3| Differential output voltage |VOD| Change g in magnitude g of diferential output voltage VOC Common mode output voltage Common-mode |VOC| Change of g in magnitude g common-mode output voltage IO IOZ Output current IIH IIL High-level input current IOS Short-circuit output current ICC High-impedance-state output current Low-level input current Supply current (total package) TYP MIN MAX UNIT - 1.5 V 0 6 V 1.5 6 V RL = 100 , See Figure 1 1/2 VOD1 or 2 RL = 54 , See Figure 1 1.5 See Note 3 V 2.5 1.5 RL = 54 or 100 , See Figure 1 5 5 V 0.2 02 V 3 -1 VCC = 0, VO = - 7 V to 12 V VO = - 7 V to 12 V VI = 2.4 V VI = 0.4 V VO = - 7 V VO = VCC VO = 12 V V 02 0.2 V 100 A 100 A 20 A - 400 A - 250 250 mA 250 No load Outputs enabled 57 70 Outputs disabled 26 35 mA All typical values are at VCC = 5 V and TA = 25C. |VOD| and |VOC| are the changes in magnitude of VOD and VOC, respectively, that occur when the input is changed from a high level to a low level. The minimum VOD2 with a 100- load is either 1/2 VOD1 or 2, whichever is greater. NOTE 3: See Figure 3.5 of EIA Standard RS-485. switching characteristics, VCC = 5 V, TA = 25C PARAMETER TEST CONDITIONS tdD ttD Differential-output delay time tPZH tPZL Output enable time to high level RL = 110 , Output enable time to low level RL = 110 , tPHZ tPLZ Output disable time from high level RL = 110 , Output disable time from low level RL = 110 , 2-4 Differential-output transition time RL = 54 , POST OFFICE BOX 655303 TYP MAX 15 20 ns 20 30 ns See Figure 4 85 120 ns See Figure 5 40 60 ns See Figure 4 150 250 ns See Figure 5 20 30 ns See Figure 3 * DALLAS, TEXAS 75265 MIN UNIT SN75177B, SN75178B DIFFERENTIAL BUS REPEATERS SLLS002C - D2606, JULY 1985 - REVISED FEBRUARY 1993 SYMBOL EQUIVALENTS DATA SHEET PARAMETER RS-422-A RS-485 VO |VOD1| Voa, Vob Vo Voa, Vob Vo |VOD2| Vt (RL = 100 ) Vt (RL = 54 ) Vt (Test Termination) Measurement 2) |VOD| | |Vt| - |Vt|| | |Vt| - |Vt|| VOC |VOC| IOS |VOS| |VOS - VOS| |VOS| |VOS - VOS| IO |Ixa|,|Ixb| |VOD3| |Isa|,|Isb| Iia,Iib RECEIVER SECTION electrical characteristics over recommended ranges of common-mode input voltage, supply voltage, and operating free-air temperature (unless otherwise noted) PARAMETER VT+ VT- Positive-going input threshold voltage Vhys VIK Input hysteresis (VT+ - VT-) TEST CONDITIONS VO = 2.7 V, VO = 0.5 V, Negative-going input threshold voltage IO = - 0.4 mA IO = 8 mA TYP MAX 0.2 - 0.2 Input clamp voltage at EN II = - 18 mA VID = 200 mV, See Figure 2 IOH = - 400 A, IOL = 8 mA, High-level output voltage VOL Low-level output voltage VID = - 200 mV, See Figure 2 IOZ High impedance state output current High-impedance-state VO = 0.4 0 4 V to 2 2.4 4V II Line input current Other input at 0 V, See Note 4 IIH IIL High-level enable-input current ri Input resistance IOS Short-circuit output current 2.7 0.45 20 - 400 VI = 12 V VI = - 7 V 1 - 0.8 20 - 200 V A mA A A k - 15 No load V V 12 Supply Su ly current (total package) ackage) V mV - 1.5 VIH = 2.7 V VIL = 0.4 V Low-level enable-input current UNIT V 50 VOH ICC MIN - 85 Outputs enabled 57 70 Outputs disabled 26 35 mA mA All typical values are at VCC = 5 V, TA = 25C. The algebraic convention, where the less-positive (more-negative) limit is designated minimum, is used in this data sheet for common-mode input voltage and threshold voltage levels only. NOTE 4: Refer to EIA Standard RS-422 for exact conditions. switching characteristics, VCC = 5 V, TA = 25C PARAMETER TEST CONDITIONS tPLH tPHL Propagation delay time, low-to-high level output tPZH tPZL Output enable time to high level tPHZ tPLZ Output disable time from high level Propagation delay time, high-to-low level output Output enable time to high level Output disable time from low level POST OFFICE BOX 655303 VID = - 1.5 V to 1.5 V,, CL = 15 pF, See Figure 6 CL = 15 pF, pF See Figure 7 CL = 15 pF, pF See Figure 8 * DALLAS, TEXAS 75265 MIN TYP MAX 19 35 30 40 10 20 12 20 25 35 17 25 UNIT ns ns ns 2-5 SN75177B, SN75178B DIFFERENTIAL BUS REPEATERS SLLS002C - D2606, JULY 1985 - REVISED FEBRUARY 1993 PARAMETER MEASUREMENT INFORMATION RL VOD2 2 VID RL 2 VOH VOC +IOL VOL Figure 1. Driver VOD and VOC - IOH Figure 2. Receiver VOH and VOL 3V Input Generator (see Note A) RL = 54 50 1.5 V CL = 50 pF (see Note B) 1.5 V 0V tdD tdD Output Output 90% 50% 2.5 V 50% 10% - 2.5 V ttD VOLTAGE WAVEFORMS ttD TEST CIRCUIT Figure 3. Driver Differential-Output Test Circuit and Voltage Waveforms Output S1 0 V or 3 V Generator (see Note A) AAAA AAAA AAAA (SN75178B) Input 3V 1.5 V 1.5 V (SN75177B) 50 CL = 50 pF (see Note B) SN75178B Enable is Active Low 0V 0.5 V tPZH RL = 110 VOH Output 2.3 V tPHZ Voff 0 V VOLTAGE WAVEFORMS TEST CIRCUIT Figure 4. Driver Enable and Disable Times 5V S1 RL = 110 Output 3 V or 0 V Generator (see Note A) 50 SN75178B Enable is Active Low AAAA AAAA AAAA (SN75178B) Input 3V 1.5 V 1.5 V 0V (SN75177B) tPZL tPLZ CL = 50 pF (see Note B) Output 2.3 V 5V 0.5 V VOL VOLTAGE WAVEFORMS TEST CIRCUIT Figure 5. Driver Enable and Disable Times NOTES: A. The input pulse is supplied by a generator having the following characteristics: PRR 1 MHz, 50% duty cycle, tr 6 ns, tf 6 ns, ZO = 50 . B. CL includes probe and jig capacitance. 2-6 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN75177B, SN75178B DIFFERENTIAL BUS REPEATERS SLLS002C - D2606, JULY 1985 - REVISED FEBRUARY 1993 PARAMETER MEASUREMENT INFORMATION 3V Input Generator (see Note A) 1.5 V Output 50 1.5 V 0V 1.5 V CL = 15 pF (see Note B) tPHL tPLH VOH Output 1.3 V 1.3 V VOL TEST CIRCUIT VOLTAGE WAVEFORMS Figure 6. Receiver Propagation Delay Times S1 1.5 V Output S2 2 k -1.5 V 5V CL = 15 pF (see Note B) Generator (see Note A) 5 k (see Note C) 50 S3 TEST CIRCUIT AAAA AAAA AAAA (SN75177B) Input 3V S1 to 1.5 V S2 Open S3 Closed 0V 1.5 V (SN75178B) tPZH AAAAA AAAAA AAAAA AAAAA (SN75177B) Input (SN75178B) 3V S1 to -1.5 V S2 Closed S3 Open 0V 1.5 V tPZL VOH 1.5 V Output AAAA AAAA AAAA 0V (SN75177B) Input (SN75178B) 1.5 V 3V S1 to 1.5 V S2 Closed S3 Closed 0V tPHZ Output 0.5 V 4.5 V Output AAAAA AAAAA AAAAA 1.5 V VOL (SN75177B) Input (SN75178B) 3V S1 to -1.5 V S2 Closed S3 Closed 0V 1.5 V tPLZ 1.3 V VOH Output 0.5 V 1.3 V VOL VOLTAGE WAVEFORMS Figure 7. Receiver Output Enable and Disable Times NOTES: A. The input pulse is supplied by a generator having the following characteristics: PRR 1 MHz, 50% duty cycle, tr 6 ns, tf 6 ns, ZO = 50 . B. CL includes probe and jig capacitance. C. All diodes are 1N916 or equivalent. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 2-7 SN75177B, SN75178B DIFFERENTIAL BUS REPEATERS SLLS002C - D2606, JULY 1985 - REVISED FEBRUARY 1993 TYPICAL CHARACTERISTICS DRIVER HIGH-LEVEL OUTPUT VOLTAGE vs HIGH-LEVEL OUTPUT CURRENT DRIVER LOW-LEVEL OUTPUT VOLTAGE vs LOW-LEVEL OUTPUT CURRENT 5 5 VCC = 5 V TA = 25C 4 3.5 3 2.5 2 AA AA AA 1.5 1 VCC = 5 V TA = 25C 4.5 VOH - High-Level Output Voltage - V VOH - High-Level Output Voltage - V 4.5 4 3.5 3 2.5 2 AAA AAA AAA 1.5 1 0.5 0.5 0 - 20 0 - 40 - 60 - 80 - 100 - 120 0 0 20 40 80 100 120 IOH - Low-Level Output Current - mA IOH - High-Level Output Current - mA Figure 8 Figure 9 DRIVER DIFFERENTIAL OUTPUT VOLTAGE vs DRIVER OUTPUT CURRENT RECEIVER OUTPUT VOLTAGE vs DIFFERENTIAL INPUT VOLTAGE 5 4 VCC = 5 V VCC = 5 V TA = 25C 3.5 IO = 0 TA = 25C 4 VO V O - Output Voltage - V VOD - Differential Output Voltage - V 60 3 2.5 2 1.5 AA AA VIC = - 12 V VIC = 0V VIC = 12 V 3 VT- VT+ VT- VT- VT+ VT+ 2 1 1 0.5 0 0 10 20 30 40 50 60 70 80 90 100 0 -125 -100 -75 -50 -25 IO - Output Current - mA Figure 10 2-8 0 25 Figure 11 POST OFFICE BOX 655303 50 75 100 125 VID - Differential Input Voltage - mV * DALLAS, TEXAS 75265 SN75177B, SN75178B DIFFERENTIAL BUS REPEATERS SLLS002C - D2606, JULY 1985 - REVISED FEBRUARY 1993 TYPICAL CHARACTERISTICS RECEIVER HIGH-LEVEL OUTPUT VOLTAGE vs HIGH-LEVEL OUTPUT CURRENT RECEIVER HIGH-LEVEL OUTPUT VOLTAGE vs FREE-AIR TEMPERATURE 5 VID = 0.2 V TA = 25C VOH - High-Level Output Voltage - V VOH - High-Level Output Voltage - V 5 4 3 VCC = 5.25 V 2 AA AA AA VCC = 5 V VCC = 4.75 V 1 VCC = 5 V VID = 200 mV IOH = - 440 A 4 3 2 AA AA AA 1 0 0 0 - 10 - 20 - 30 - 40 - 50 0 10 20 Figure 12 0.6 0.5 VOL - Low-Level Output Voltage - V VOL - Low-Level Output Voltage - V VCC = 5 V TA = 25C 0.4 0.3 0.2 0.1 0 15 60 70 80 RECEIVER LOW-LEVEL OUTPUT VOLTAGE vs FREE-AIR TEMPERATURE 0.6 10 50 Figure 13 RECEIVER LOW-LEVEL OUTPUT VOLTAGE vs LOW-LEVEL OUTPUT CURRENT 5 40 TA - Free-Air Temperature - C IOH - High-Level Output Current - mA 0 30 20 25 30 0.5 VCC = 5 V VID = - 200 mV IOL = 8 mA 0.4 0.3 0.2 0.1 0 - 40 - 20 0 20 40 60 80 100 120 TA - Free-Air Temperature - C IOL - Low-Level Output Current - mA Figure 14 Figure 15 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 2-9 SN75177B, SN75178B DIFFERENTIAL BUS REPEATERS SLLS002C - D2606, JULY 1985 - REVISED FEBRUARY 1993 APPLICATION INFORMATION 1/2 SN75179B Direction RT RT Control SN75177B 1/2 SN75179B SN75176B SN75176B RT RT RT RT SN75178B SN75176B NOTE: The line should be terminated at both ends in its characteristic impedance. Stub lengths off the main line should be kept as short as possible. Figure 16. Typical Application Circuit 2-10 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 PACKAGE OPTION ADDENDUM www.ti.com 28-Aug-2010 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) Samples (Requires Login) SN75177BD OBSOLETE SOIC D 8 TBD Call TI Call TI Samples Not Available SN75177BP OBSOLETE PDIP P 8 TBD Call TI Call TI Samples Not Available SN75178BD OBSOLETE SOIC D 8 TBD Call TI Call TI Samples Not Available SN75178BDR OBSOLETE SOIC D 8 TBD Call TI Call TI Samples Not Available SN75178BP ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type Contact TI Distributor or Sales Office SN75178BPE4 ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type Contact TI Distributor or Sales Office (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DLP(R) Products www.dlp.com Communications and Telecom www.ti.com/communications DSP dsp.ti.com Computers and Peripherals www.ti.com/computers Clocks and Timers www.ti.com/clocks Consumer Electronics www.ti.com/consumer-apps Interface interface.ti.com Energy www.ti.com/energy Logic logic.ti.com Industrial www.ti.com/industrial Power Mgmt power.ti.com Medical www.ti.com/medical Microcontrollers microcontroller.ti.com Security www.ti.com/security RFID www.ti-rfid.com Space, Avionics & Defense www.ti.com/space-avionics-defense RF/IF and ZigBee(R) Solutions www.ti.com/lprf Video and Imaging www.ti.com/video Wireless www.ti.com/wireless-apps Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2010, Texas Instruments Incorporated