Vishay Siliconix
Si4848DY
Document Number: 71356
S09-0870-Rev. C, 18-May-09
www.vishay.com
1
N-Channel 150-V (D-S) MOSFET
FEATURES
• Halogen-free According to IEC 61249-2-21
Definition
• TrenchFET® Power MOSFETs
• Compliant to RoHS Directive 2002/95/EC
PRODUCT SUMMARY
VDS (V) RDS(on) (Ω)I
D (A)
150 0.085 at VGS = 10 V 3.7
0.095 at VGS = 6.0 V 3.5
SO-8
D
D
D
D
S
S
S
G5
6
7
8
Top View
2
3
4
1
Ordering Information: Si4848DY-T1-E3 (Lead (Pb)-free)
Si4848DY-T1-GE3 (Lead (Pb)-free and Halogen-free)
D
G
S
N-Channel MOSFET
Notes:
a. Surface Mounted on 1" x 1" FR4 board.
ABSOLUTE MAXIMUM RATINGS TA = 25 °C, unless otherwise noted
Parameter Symbol 10 s Steady State Unit
Drain-Source Voltage VDS 150 V
Gate-Source Voltage VGS ± 20
Continuous Drain Current (TJ = 150 °C)aTA = 25 °C ID
3.7 2.7
A
TA = 70 °C 3.0 2.1
Pulsed Drain Current IDM 25
Avalanche Current L = 0.1 mH IAS 10
Continuous Source Current (Diode Conduction)aIS2.5 1.3
Maximum Power DissipationaTA = 25 °C PD
3.0 1.5 W
TA = 70 °C 1.9 1.0
Operating Junction and Storage Temperature Range TJ, Tstg - 55 to 150 °C
THERMAL RESISTANCE RATINGS
Parameter Symbol Typical Maximum Unit
Maximum Junction-to-Ambientat ≤ 10 s RthJA
35 42
°C/W
Steady State 68 82
Maximum Junction-to-Foot (Drain) Steady State RthJF 18 23
www.vishay.com
2
Document Number: 71356
S09-0870-Rev. C, 18-May-09
Vishay Siliconix
Si4848DY
Notes:
a. Pulse test; pulse width ≤ 300 µs, duty cycle ≤ 2 %.
b. Guaranteed by design, not subject to production testing.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation
of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
TYPICAL CHARACTERISTICS 25 °C, unless otherwise noted
SPECIFICATIONS TJ = 25 °C, unless otherwise noted
Parameter Symbol Test Conditions Min. Typ. Max. Unit
Static
Gate Threshold Voltage VGS(th) VDS = VGS, ID = 250 µA 2.0 V
Gate-Body Leakage IGSS VDS = 0 V, VGS = ± 20 V ± 100 nA
Zero Gate Voltage Drain Current IDSS
VDS = 120 V, VGS = 0 V 1µA
VDS = 120 V, VGS = 0 V, TJ = 55 °C 5
On-State Drain CurrentaID(on) V
DS ≥ 5 V, VGS = 10 V 25 A
Drain-Source On-State ResistanceaRDS(on)
VGS = 10 V, ID = 3.5 A 0.068 0.085 Ω
VGS = 6.0 V, ID = 3.0 A 0.076 0.095
Forward Transconductanceagfs VDS = 15 V, ID = 5 A 15 S
Diode Forward VoltageaVSD IS = 2.5 A, VGS = 0 V 0.75 1.2 V
Dynamicb
Total Gate Charge Qg
VDS = 75 V, VGS = 10 V, ID = 3.5 A
17 21
nCGate-Source Charge Qgs 3.2
Gate-Drain Charge Qgd 6.0
Gate Resistance Rg0.5 0.85 1.8 Ω
Tur n - O n D e l ay Time td(on)
VDD = 75 V, RL = 21 Ω
ID ≅ 3.5 A, VGEN = 10 V, Rg = 6 Ω
9.0 14
ns
Rise Time tr10 15
Turn-Off Delay Time td(off) 24 35
Fall Time tf17 25
Source-Drain Reverse Recovery Time trr IF = 2.5 A, dI/dt = 100 A/µs 45 70
Output Characteristics
0
5
10
15
20
25
0246810
VGS = 10 V thru 6 V
VDS
- Drain-to-Source Voltage (V)
- Drain Current (A)ID
5 V
3 V, 4 V
Transfer Characteristics
0
5
10
15
20
25
0123456
TC = 125 °C
25 °C
VGS
- Gate-to-Source Voltage (V)
- Drain Current (A)ID
- 55 °C
Document Number: 71356
S09-0870-Rev. C, 18-May-09
www.vishay.com
3
Vishay Siliconix
Si4848DY
TYPICAL CHARACTERISTICS 25 °C, unless otherwise noted
On-Resistance vs. Drain Current
Gate Charge
Source-Drain Diode Forward Voltage
RDS(on)
0.00
0.03
0.06
0.09
0.12
0.15
0 5 10 15 20 25
ID
- Drain Current (A)
VGS = 6 V
VGS = 10 V
- On-Resistance (Ω)
0
4
8
12
16
20
0 6 12 18 24 30
V
DS
= 75 V
I
D
= 3.5 A
- Gate-to-Source Voltage (V)
Q
g
- Total Gate Charge (nC)
V
GS
0.0 0.2 0.4 0.6 0.8 1.0 1.2
TJ = 150 °C TJ = 25 °C
50
10
1
VSD
- Source-to-Drain Voltage (V)
- Source Current (A)IS
Capacitance
On-Resistance vs. Junction Temperature
On-Resistance vs. Gate-to-Source Voltage
0
300
600
900
1200
0 30 60 90 120 150
VDS
- Drain-to-Source Voltage (V)
Crss
Coss
Ciss
C - Capacitance (pF)
0.0
0.5
1.0
1.5
2.0
2.5
3.0
- 50 - 25 0 25 50 75 100 125 150
VGS = 10 V
ID = 3.5 A
TJ - Junction Temperature (°C)
(Normalized)
- On-ResistanceRDS(on)
0.00
0.05
0.10
0.15
0.20
0.25
0246810
ID = 3.5 A
- On-Resistance RDS(on)
VGS - Gate-to-Source Voltage (V)
www.vishay.com
4
Document Number: 71356
S09-0870-Rev. C, 18-May-09
Vishay Siliconix
Si4848DY
TYPICAL CHARACTERISTICS 25 °C, unless otherwise noted
Vishay Siliconix maintains worldwide manufacturing capability. Products may be manufactured at one of several qualified locations. Reliability data for Silicon
Technology and Package Reliability represent a composite of all qualified locations. For related documents such as package/tape drawings, part marking, and
reliability data, see www.vishay.com/ppg?71356.
Threshold Voltage
- 1.5
- 1.0
- 0.5
0.0
0.5
1.0
- 50 - 25 0 25 50 75 100 125 150
ID = 250 µA
Variance (V)VGS(th)
TJ - Temperature (°C)
Single Pulse Power
0
30
60
10
20
Power (W)
Time (s)
1 10010
40
0.10.01
50
Normalized Thermal Transient Impedance, Junction-to-Ambient
10-3 10-2 1 10 60010-1
10-4 100
2
1
0.1
0.01
0.2
0.1
0.05
0.02
Single Pulse
Duty Cycle = 0.5
Square Wave Pulse Duration (s)
Normalized Effective Transient
Thermal Impedance
1. Duty Cycle, D =
2. Per Unit Base = RthJA = 68 °C/W
3. TJM - T
A = PDMZthJA(t)
t1
t2
t1
t2
Notes:
4. Surface Mounted
PDM
Normalized Thermal Transient Impedance, Junction-to-Foot
10-3 10-2 1 100010-1
10-4
2
1
0.1
0.01
0.2
0.1
0.05
0.02
Single Pulse
Duty Cycle = 0.5
Square Wave Pulse Duration (s)
Normalized Effective Transient
Thermal Impedance
10 100
Vishay Siliconix
Package Information
Document Number: 71192
11-Sep-06
www.vishay.com
1
DIM
MILLIMETERS INCHES
Min Max Min Max
A 1.35 1.75 0.053 0.069
A10.10 0.20 0.004 0.008
B 0.35 0.51 0.014 0.020
C 0.19 0.25 0.0075 0.010
D 4.80 5.00 0.189 0.196
E 3.80 4.00 0.150 0.157
e 1.27 BSC 0.050 BSC
H 5.80 6.20 0.228 0.244
h 0.25 0.50 0.010 0.020
L 0.50 0.93 0.020 0.037
q0°8°0°8°
S 0.44 0.64 0.018 0.026
ECN: C-06527-Rev. I, 11-Sep-06
DWG: 5498
4
3
12
5
6
87
HE
h x 45
C
All Leads
q0.101 mm
0.004"
L
BA
1
A
e
D
0.25 mm (Gage Plane)
SOIC (NARROW): 8-LEAD
JEDEC Part Number: MS-012
S
VISHAY SILICONIX
TrenchFET® Power MOSFETs Application Note 808
Mounting LITTLE FOOT®, SO-8 Power MOSFETs
APPLICATION NOTE
Document Number: 70740 www.vishay.com
Revision: 18-Jun-07 1
Wharton McDaniel
Surface-mounted LITTLE FOOT power MOSFETs use
integrated circuit and small-signal packages which have
been been modified to provide the heat transfer capabilities
required by power devices. Leadframe materials and
design, molding compounds, and die attach materials have
been changed, while the footprint of the packages remains
the same.
See Application Note 826, Recommended Minimum Pad
Patterns With Outline Drawing Access for Vishay Siliconix
MOSFETs, (http://www.vishay.com/ppg?72286), for the
basis of the pad design for a LITTLE FOOT SO-8 power
MOSFET. In converting this recommended minimum pad
to the pad set for a power MOSFET, designers must make
two connections: an electrical connection and a thermal
connection, to draw heat away from the package.
In the case of the SO-8 package, the thermal connections
are very simple. Pins 5, 6, 7, and 8 are the drain of the
MOSFET for a s ingle MOSFET package and are connected
together. In a dual package, pins 5 and 6 are one drain, and
pins 7 and 8 are the other drain. For a small-signal device or
integrated circuit, typical connections would be made with
traces that are 0.020 inches wide. Since the drain pins serve
the additional function of providin g the thermal connect ion
to the package, this level of connection is inadequate. The
total cross section of the copper may be adequate to carry
the current required for the application, but it presents a
large thermal impedance. Also, heat spreads in a circular
fashion from the heat source. In this case the drain pins are
the heat sources when looking at heat spread on the PC
board.
Figure 1. Single M O SFET SO-8 Pad
Pattern With Copper Spreading
Figure 2. Dual MOSFET SO-8 Pad Pattern
With Copper Spreading
The minimum recommended pad patterns for the
single-MOSFET SO-8 with copper spreading (Figure 1) and
dual-MOSFET SO-8 with copper spreading (Figure 2) show
the starting point for utilizing the board area available for the
heat-spreading copper. To create this pattern, a plane of
copper overlies the drain pins. The copper plane connects
the drain pins electrically, but more importantly provides
planar copper to draw heat from the drain leads and start the
process of spreading the heat so it can be dissipated into the
ambient air. These patterns use all the available area
underneath the body for this purpose.
Since surface-mounted packages are small, and reflow
soldering is the most common way in which these are
affixed to the PC board, “thermal” connections from the
planar copper to the pads have not been used. Even if
additional planar copper area is used, there should be no
problems in the soldering process. The actual solder
connections are defined by the solder mask openings. By
combining the basic footpri nt with the copper plane on the
drain pins, the solder mask generation occurs automatically.
A final item to keep in mind is the width of the power traces.
The absolute minimum power trace width must be
determined by the amount of current it has to carry. For
thermal reasons, this minimum width should be at least
0.020 inches. The use of wide traces connected to the drain
plane provides a low impedance path for heat to move away
from the device.
0.027
0.69
0.078
1.98
0.2
5.07
0.196
5.0
0.288
7.3
0.050
1.27
0.027
0.69
0.078
1.98
0.2
5.07
0.088
2.25
0.288
7.3
0.050
1.27
0.088
2.25
Application Note 826
Vishay Siliconix
www.vishay.com Document Number: 72606
22 Revision: 21-Jan-08
APPLICATION NOTE
RECOMMENDED MINIMUM PADS FOR SO-8
0.246
(6.248)
Recommended Minimum Pads
Dimensions in Inches/(mm)
0.172
(4.369)
0.152
(3.861)
0.047
(1.194)
0.028
(0.711)
0.050
(1.270)
0.022
(0.559)
Return to Index
Return to Index
Legal Disclaimer Notice
www.vishay.com Vishay
Revision: 12-Mar-12 1Document Number: 91000
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree
to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and
damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay
or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to
obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
