RGL34A THRU RGL34J
SURFACE MOUNT GLASS PASSIVATED JUNCTION FAST SWITCHING RECTIFIER
Reverse Voltage - 50 to 600 Volts Forward Current - 0.5 Ampere
FEATURES
♦ Plastic package has Underwriters Laboratory
Flammability Classification 94V-0
♦ For surface mount applications
♦ High temperature metallurgically bonded construction
♦ Glass passivated cavity-free junction
♦ Capable of meeting environmental standards of
MIL-S-19500
♦ Fast switching for high efficiency
♦ High temperature soldering guaranteed:
450°C/5 seconds at terminals. Complete device
submersible temperature of 260°C for 10 seconds in
solder bath
MECHANICAL DATA
Case: JEDEC DO-213AA molded plastic over glass body
Terminals: Plated terminals, solderable per MIL-STD-750,
Method 2026
Polarity: Two bands indicate cathode end - 1st band
denotes device type and 2nd band denotes repetitive peak
reverse voltage rating
Mounting Position: Any
Weight: 0.0014 ounce, 0.036 gram
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25°°C ambient temperature unless otherwise specified.
Fast switching device: 1st band is Red
SYMBOLS RGL34A RGL34B RGL34D RGL34G RGL34J UNITS
Polarity color bands (2nd Band) Gray Red Orange Yellow Green
Maximum repetitive peak reverse voltage VRRM 50 100 200 400 600 Volts
Maximum RMS voltage VRMS 35 70 140 280 420 Volts
Maximum DC blocking voltage VDC 50 100 200 400 600 Volts
Maximum average forward rectified current
at TT=55°C I(AV) 0.5 Amp
Peak forward surge current
8.3ms single half sine-wave superimposed
on rated load (JEDEC Method) IFSM 10.0 Amps
Maximum instantaneous forward voltage at 0.5A VF1.3 Volts
Maximum DC reverse current TA=25°C 5.0
at rated DC blocking voltage TA=125°C IR50.0 µA
Maximum full load reverse current, full cycle
av er age TA=55°C IR(AV) 30.0 µA
Maximum reverse recover y time (NOTE 1) trr 150 250 ns
Typical junction capacitance (NOTE 2) CJ4.0 pF
Maximum thermal resistance (NOTE 3) RΘJA 150.0
(NOTE 4) RΘJT 70.0 °C/W
Operating junction and storage temperature range TJ, TSTG -65 to +175 °C
NOTES:
(1) Reverse recovery test conditions IF=0.5A, IR=1.0A, Irr=0.25A
(2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts
(3) Ther mal resistance from junction to ambient, 0.2 x 0.2” (5.0 x 5.0mm) copper pads to each terminal
(4) Ther mal resistance from junction to ter minal, 0.2 x 0.2” (5.0 x 5.0mm) copper pads to each terminal
4/98
SOLDERABLE ENDS
1st BAND
2nd BAND
0.022 (0.559)
0.016 (0.406)
0.145 (3.683)
0.131(3.327)
D1=
0.066
0.060
(1.676)
(1.524)
D2 = D1
+ 0
- 0.008 (0.20)
1st band denotes type and polarity
2cnd band denotes voltage type
D2
Dimensions in inches and (millimeters)
*
Glass-plastic encapsulation technique is covered by
Patent No.3,996,602 and brazed-lead assembly by Patent No.3,930,306
DO-213AA
PATENTED*
®
0 25 50 75 100 125 150 175
0
0.1
0.2
0.3
0.4
0.5
110 100
0
2.0
4.0
6.0
8.0
12
0.2 0.4 0.6 0.8 1.0
1
10
110100
1
10
10
1.2 1.4 1.6
0.1
0.01
020406080100
0.01
0.1
1
10
RATINGS AND CHARACTERISTIC CURVES RGL34A THRU RGL34J
FIG. 1 - FORWARD CURRENT
DERATING CURVE
TERMINAL TEMPERATURE, °C
AVERAGE FORWARD RECTIFIED
CURRENT, AMPERES
FIG. 2 - MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT
NUMBER OF CYCLES AT 60 HZ
PEAK FORWARD SURGE CURRENT,
AMPERES
FIG. 3 - TYPICAL INSTANTANEOUS
FORWARD CHARACTERISTICS FIG. 4 - TYPICAL REVERSE CHARACTERISTICS
INSTANTANEOUS FORWARD CURRENT, AMPERES
INSTANTANEOUS REVERSE CURRENT,
MICROAMPERES
INSTANTANEOUS FOR WARD VOLTAGE, V OLTS
FIG. 5 - TYPICAL JUNCTION CAPACITANCE
JUNCTION CAPACITANCE, pF
REVERSE V OLTAGE, VOLTS
TJ=TJmax.
8.3ms SINGLE HALF SINE-WAVE
(JEDEC Method)
TJ= 25°C
TJ=25°C
PULSE WIDTH=300µs
1% DUTY CYCLE
TJ=25°C
f=1.0 MHz
Vsig=50mVp-p
RESISTIVE OR
INDUCTIVE LOAD
TJ=100°C
PERCENT OF RATED PEAK REVERSE
VOLTAGE, %
