Fully Accurate, 16-Bit, Unbuffered VOUT, Quad SPI Interface, 2.7 V to 5.5 V nanoDAC in a TSSOP AD5066 FEATURES Total unadjusted error for the part is <0.8 mV. Zero code error for the part is 0.05 mV typically. Low power quad 16-bit nanoDAC, 1 LSB INL Low total unadjusted error of 0.1 mV typically Low zero code error of 0.05 mV typically Individually buffered reference pins 2.7 V to 5.5 V power supply Specified over full code range of 0 to 65535 Power-on reset to zero scale or midscale Per channel power-down with 3 power-down functions Hardware LDAC with software LDAC override function CLR function to programmable code Small 16-lead TSSOP The AD5066 contains a power-down feature that reduces the current consumption of the device to typically 400 nA at 5 V and provides software selectable output loads while in powerdown mode. The outputs of all DACs can be updated simultaneously using the hardware LDAC function, with the added functionality of user software selectable DAC channels to update simultaneously. There is also an asynchronous CLR that clears all DACs to a software-selectable code--0 V, midscale, or full scale. PRODUCT HIGHLIGHTS APPLICATIONS 1. 2. 3. 4. 5. 6. Process control Data acquisition systems Portable battery-powered instruments Digital gain and offset adjustment Programmable voltage and current sources GENERAL DESCRIPTION Quad channel available in 16-lead TSSOP, 1 LSB INL. Individually buffered voltage reference pins. TUE = 0.8 mV max and zero code error = 0.1 mV max. High speed serial interface with clock speeds up to 50 MHz. Three power-down modes available to the user. Reset to known output voltage (zero scale or midscale). Table 1. Related Devices The AD5066 is a low power, 16-bit quad-channel, unbuffered voltage output nanoDAC(R) offering relative accuracy specifications of 1 LSB INL with individual reference pins and can operate from a single 2.7 V to 5.5 V supply. The AD5066 also offers a differential accuracy specification of 1 LSB DNL. Reference buffers are also provided on-chip. The part uses a versatile 3-wire, low power Schmitt trigger serial interface that operates at clock rates up to 50 MHz and is compatible with standard SPI(R), QSPITM, MICROWIRETM, and most DSP interface standards. The AD5066 incorporates a power-on reset circuit that ensures the DAC output powers up to zero scale or midscale and remains there until a valid write to the device takes place. Part No. AD5666 AD5025/AD5045/AD50651 AD5024/AD5044/AD50641 AD50621 AD50631 AD5061 AD5040/AD50601 1 Description Quad,16-bit buffered DAC,16 LSB INL, TSSOP Dual,12-/14-/16-bit buffered nanoDAC, TSSOP Quad 16-bit nanoDAC, TSSOP Single, 16-bit nanoDAC, SOT-23 Single, 16-bit nanoDAC, MSOP Single,16-bit nanoDAC, 4 LSB INL, SOT-23 14-/16-bit nanoDAC, SOT-23 1 LSB INL FUNCTIONAL BLOCK DIAGRAM VREF A VREF B VDD AD5066 SCLK SYNC INTERFACE LOGIC DIN INPUT REGISTER DAC REGISTER DAC A VOUTA INPUT REGISTER DAC REGISTER DAC B VOUTB INPUT REGISTER DAC REGISTER DAC C VOUTC INPUT REGISTER DAC REGISTER DAC D VOUTD POWER-ON RESET LDAC CLR POR POWER-DOWN LOGIC VREF C VREF D GND 06845-001 LDAC Figure 1. Rev. A Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. www.analog.com Tel: 781.329.4700 Fax: 781.461.3113 (c)2009-2010 Analog Devices, Inc. All rights reserved. AD5066 TABLE OF CONTENTS Features .............................................................................................. 1 DAC Architecture....................................................................... 15 Applications ....................................................................................... 1 Reference Buffer ......................................................................... 15 General Description ......................................................................... 1 Serial Interface ............................................................................ 15 Product Highlights ........................................................................... 1 Input Shift Register .................................................................... 15 Functional Block Diagram .............................................................. 1 Power-On Reset .......................................................................... 17 Revision History ............................................................................... 2 Clear Code Register ................................................................... 18 Specifications..................................................................................... 3 LDAC Function ........................................................................... 18 AC Characteristics ........................................................................ 4 Power Supply Bypassing and Grounding ................................ 19 Timing Characteristics ................................................................ 5 Microprocessor Interfacing ....................................................... 19 Absolute Maximum Ratings ............................................................ 6 Applications Information .............................................................. 21 ESD Caution .................................................................................. 6 Using a Reference as a Power Supply ....................................... 21 Pin Configuration and Function Descriptions ............................. 7 Bipolar Operation....................................................................... 21 Typical Performance Characteristics ............................................. 8 Using the AD5066 with a Galvanically Isolated Interface .... 21 Terminology .................................................................................... 14 Outline Dimensions ....................................................................... 22 Theory of Operation ...................................................................... 15 Ordering Guide .......................................................................... 22 Digital-to-Analog Converter .................................................... 15 REVISION HISTORY 8/10--Rev. 0 to Rev. A Change to Minimum SYNC High Time, Single Channel Update Parameter, Table 4 ............................................... 5 7/09--Revision 0: Initial Version Rev. A | Page 2 of 24 AD5066 SPECIFICATIONS VDD = 2.7 V to 5.5 V, 2.0 V VREFA, VREFB, VREFC, VREFD VDD - 0.4 V, all specifications TMIN to TMAX, unless otherwise noted. Table 2. Parameter STATIC PERFORMANCE2 Resolution Relative Accuracy (INL) Min IDD Normal Mode6 All Power-Down Modes7 Min 16 Differential Nonlinearity (DNL) Total Unadjusted Error (TUE) Zero-Code Error Zero-Code Error Drift3 Full-Scale Error Gain Error Gain Error Drift3 DC Crosstalk3 OUTPUT CHARACTERISTICS3 Output Voltage Range DC Output Impedance (Normal Mode) DC Output Impedance Output Connected to 100 k Network Output Connected to 1 k Network Power-Up Time4 DC PSRR REFERENCE INPUTS Reference Input Range Reference Current Reference Input Impedance LOGIC INPUTS3 Input Current5 Input Low Voltage, VINL Input High Voltage, VINH Pin Capacitance POWER REQUIREMENTS VDD A Grade1 Typ Max B Grade1 Typ Max 16 0.5 0.5 0.2 0.1 0.05 0.5 0.01 0.005 0.5 1 5 0 4 4 1 0.8 0.1 Unit Bits LSB Conditions/Comments 1 2 1 0.8 0.1 5 0.5 0.5 0.2 0.1 0.05 0.5 0.01 0.005 0.5 1 5 LSB mV mV V/C % FSR % FSR ppm V 25 5 25 V ppm of FSR/C Due to single-channel full-scale output change Due to powering down (per channel) VREF 0.05 0.05 VREF VDD = 2.7 V, VREF = 2 V All 0s loaded to the DAC register All 1s loaded to the DAC register 8 8 V k Output impedance tolerance 10% 100 100 k DAC in power-down mode Output impedance tolerance 20 k 1 1 k Output impedance tolerance 400 2.9 -120 2.9 -120 s dB VDD 10%, DAC = full scale VDD - 0.4 1 V A M Per DAC channel Per DAC channel 1 0.8 A V V pF 5.5 V 3 mA A 2 0.002 40 0 0.05 0.05 TA = -40C to +105C TA = -40C to +125C VDD - 0.4 1 2 0.002 40 1 0.8 2.2 2.2 4 2.7 4 5.5 2.5 0.4 3 2.7 2.5 0.4 1 All digital inputs at 0 V or VDD DAC active, excludes load current VIH = VDD and VIL = GND Temperature range is -40C to +125C, typical at 25C. Linearity calculated using a code range of 0 to 65,535; output unloaded. Guaranteed by design and characterization; not production tested. 4 Time taken to exit power-down mode and enter normal mode, 32nd clock edge to 90% of DAC midscale value, output unloaded. 5 Current flowing into individual digital pins. VDD = 5.5 V; VREF = 4.096 V; Code = midscale. 6 Interface inactive. All DACs active. DAC outputs unloaded. 7 All four DACs powered down. 2 3 Rev. A | Page 3 of 24 AD5066 AC CHARACTERISTICS VDD = 2.7 V to 5.5 V, 2.0 V VREFA, VREFB, VREFC, VREFD VDD - 0.4 V all specifications TMIN to TMAX, unless otherwise noted. Table 3. Parameter1, 2 DYNAMIC PERFORMACE Output Voltage Settling Time Typ Max Unit Conditions/Comments3 7.5 10 s Output Voltage Settling Time 12 15 s 1/4 to 3/4 scale settling to 2 LSB, single channel update, output unloaded 1/4 to 3/4 scale settling to 2 LSB, all channel update, output unloaded Slew Rate Digital-to-Analog Glitch Impulse Reference Feedthrough Digital Feedthrough Digital Crosstalk Analog Crosstalk DAC-to-DAC Crosstalk Total Harmonic Distortion Output Noise Spectral Density 1.7 3 -70 0.02 1.7 3.7 5.4 -83 30 25 4.7 Output Noise Min V/s nV-sec dB nV-sec nV-sec nV-sec nV-sec dB nV/Hz nV/Hz V p-p 1 LSB change around major carry VREF = 3 V 0.5 V p-p, frequency = 60 Hz to 20 MHz VREF = 3 V 0.2 V p-p, frequency = 10 kHz DAC code = 0x8000, 1 kHz DAC code = 0x8000, 10 kHz 0.1 Hz to 10 Hz 1 Temperature range is -40C to +125C, typical at +25C. See the Terminology section. 3 Guaranteed by design and characterization; not production tested. 2 Rev. A | Page 4 of 24 AD5066 TIMING CHARACTERISTICS All input signals are specified with tR = tF = 1 ns/V (10% to 90% of VDD) and timed from a voltage level of (VIL + VIH)/2, VDD = 2.7 V to 5.5 V, all specifications TMIN to TMAX, unless otherwise noted. See Figure 2. Table 4. Parameter1 SCLK Cycle Time SCLK High Time SCLK Low Time SYNC to SCLK Falling Edge Set-Up Time Data Set-Up Time Data Hold Time SCLK Falling Edge to SYNC Rising Edge Minimum SYNC High Time Single Channel Update All Channel Update SYNC Rising Edge to SCLK Fall Ignore LDAC Pulse Width Low SCLK Falling Edge to LDAC Rising Edge CLR Pulse Width Low SCLK Falling Edge to LDAC Falling Edge CLR Pulse Activation Time Min 20 10 10 17 5 5 5 Typ Max 30 3 8 17 20 20 10 10 10.6 t9 t10 t11 t12 t13 t14 Maximum SCLK frequency is 50 MHz. Guaranteed by design and characterization; not production tested. t1 t9 SCLK t8 t3 t4 t2 t7 SYNC t5 D IN t6 D B 31 DB0 t 13 t 10 LDAC1 t 11 LDAC2 CLR V O UT t 12 t14 1A S Y N C H R O N O U S L D A C U P D A T E M O D E . 2S Y N C H R O N O U S L D A C U P D A T E M O D E . Figure 2. Serial Write Operation Rev. A | Page 5 of 24 Unit ns ns ns ns ns ns ns s s ns ns ns ns ns s 06845-003 1 Symbol t1 t2 t3 t4 t5 t6 t7 t8 AD5066 ABSOLUTE MAXIMUM RATINGS TA = 25C, unless otherwise noted. Table 5. Parameter VDD to GND Digital Input Voltage to GND VOUTx to GND VREFx to GND Operating Temperature Range Industrial Storage Temperature Range Junction Temperature (TJ MAX) TSSOP Package Power Dissipation JA Thermal Impedance Reflow Soldering Peak Temperature SnPb Pb-Free Rating -0.3 V to +7 V -0.3 V to VDD + 0.3 V -0.3 V to VDD + 0.3 V -0.3 V to VDD + 0.3 V -40C to +125C -65C to +150C +150C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ESD CAUTION (TJ MAX - TA)/JA 150.4C/W 240C 260C Rev. A | Page 6 of 24 AD5066 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS LDAC 1 16 SCLK SYNC 2 15 DIN VDD 3 14 GND VREF A 5 AD5066 TOP VIEW (Not to Scale) 13 VOUTB 12 VOUTD VOUTA 6 11 VREF D VOUTC 7 10 CLR POR 8 9 VREF C 06845-004 VREF B 4 Figure 3. Pin Configuration Table 6. Pin Function Descriptions Pin No. Mnemonic Description 1 LDAC 2 SYNC 3 VDD 4 5 6 7 8 VREFB VREFA VOUTA VOUTC POR 9 10 VREFC CLR 11 12 13 14 15 VREFD VOUTD VOUTB GND DIN 16 SCLK Load DAC. Logic input. This is used to update the DAC register and, consequently, the analog outputs. When tied permanently low, the addressed DAC register is updated on the falling edge of the 32nd clock. If LDAC is held high during the write cycle, the addressed DAC input shift register is updated but the output is held off until the falling edge of LDAC. In this mode, all analog outputs can be updated simultaneously on the falling edge of LDAC. Active Low Control Input. This is the frame synchronization signal for the input data. When SYNC goes low, it powers on the SCLK and DIN buffers and enables the shift register. Data is transferred in on the falling edges of the next 32 clocks. If SYNC is taken high before the 32nd falling edge, the rising edge of SYNC acts as an interrupt, and the write sequence is ignored by the device. Power Supply Input. The AD5066 can be operated from 2.7 V to 5.5 V. Decouple the supply with a 10 F capacitor in parallel with a 0.1 F capacitor to GND. External Reference Voltage Input for DAC B. External Reference Voltage Input for DAC A. Unbuffered Analog Output Voltage from DAC A. Unbuffered Analog Output Voltage from DAC C. Power-On Reset Pin. Tying this pin to GND powers the DAC outputs to zero scale on power-up. Tying this pin to VDD powers the DAC outputs to midscale. External Reference Voltage Input for DAC C. Asynchronous Clear Input. The CLR input is falling edge sensitive. When CLR is low, all LDAC pulses are ignored. When CLR is activated, the input register and the DAC register are updated with the data contained in the CLR code register--zero, midscale, or full scale. Default setting clears the output to 0 V. External Reference Voltage Input for DAC D. Unbuffered Analog Output Voltage from DAC D. Unbuffered Analog Output Voltage from DAC B. Ground Reference Point for All Circuitry on the Part. Serial Data Input. This device has a 32-bit shift register. Data is clocked into the register on the falling edge of the serial clock input. Serial Clock Input. Data is clocked into the input shift register on the falling edge of the serial clock input. Data can be transferred at rates of up to 50 MHz. Rev. A | Page 7 of 24 AD5066 TYPICAL PERFORMANCE CHARACTERISTICS 0.5 0.3 0.4 0.2 MAX INL 0.3 0.1 0 INL (LSB) INL ERROR (LSB) 0.2 -0.1 -0.2 0.1 0 MIN INL -0.1 -0.2 VDD = 5V VREF = 4.096V TA = 25C -0.3 -0.5 0 10,000 20,000 VDD = 5V TA = 25C -0.4 30,000 40,000 CODE 50,000 60,000 -0.5 06845-105 -0.4 2 Figure 4. INL Error vs. Code 5 Figure 7. INL vs. Reference Input Voltage 0.5 0.3 VDD = 5V VREF = 4.096V TA = 25C 0.2 0.4 0.3 0.1 0.2 DNL (LSB) DNL ERROR (LSB) 3 4 REFERENCE VOLTAGE (V) 06845-108 -0.3 0 -0.1 0.1 MAX DNL 0 -0.1 MIN DNL -0.2 -0.2 -0.3 VDD = 5.5V TA = 25C -0.4 10,000 20,000 30,000 40,000 CODE 50,000 60,000 -0.5 2 80 TOTAL UNADJUSTED ERROR (V) 100 0.02 0.01 0 -0.01 -0.02 -0.03 -0.04 VDD = 5V VREF = 4.096V TA = 25C -0.06 60 40 MAX TUE 20 0 -20 MIN TUE -40 -60 VDD = 5.5V TA = 25C -80 -0.07 10,000 20,000 30,000 40,000 CODE 50,000 60,000 -100 06845-107 TOTAL UNADJUSTED ERROR (mV) 0.03 0 5 Figure 8. DNL vs. Reference Input Voltage Figure 5. DNL Error vs. Code -0.05 3 4 REFERENCE VOLTAGE (V) 2 Figure 6. Total Unadjusted Error vs. Code 3 4 REFERENCE VOLTAGE (V) Figure 9. Total Unadjusted Error vs. Reference Input Voltage Rev. A | Page 8 of 24 5 06845-110 0 06845-106 -0.4 06845-109 -0.3 AD5066 1.2 0.010 1.0 0.8 0.6 GAIN ERROR (%FSR) 0.005 DNL (LSB) 0.4 0 0.2 MAX DNL 0 -0.2 MIN DNL -0.4 -0.6 -0.005 -1.2 -40 06845-111 3 4 REFERENCE VOLTAGE (V) 5 -20 Figure 10. Gain Error Vs. Reference Input Voltage 0.09 80 ZERO-SCALE ERROR (mV) 0.08 0.07 0.06 0.05 0.04 0.03 VDD = 5.5V TA = 25C 100 120 100 120 60 MAX TUE 40 20 0 -20 MIN TUE -40 -60 VDD = 5V VREF = 4.096V -80 0.01 5 -100 -40 06845-112 0 3 4 REFERENCE VOLTAGE (V) 80 -20 0 20 40 60 80 TEMPERATURE (C) Figure 11. Zero-Code Error Vs. Reference Input Voltage 06845-115 TOTAL UNADJUSTED ERROR (V) 100 2 20 40 60 TEMPERATURE (C) Figure 13. DNL vs. Temperature 0.10 0.02 0 06845-114 -1.0 -0.010 2 VDD = 5V VREF = 4.096V -0.8 VDD = 5.5V TA = 25C Figure 14. Total Unadjusted Error vs. Temperature 1.2 50 1.0 40 MAX INL 0.8 30 0.6 20 0 -0.2 MIN INL -0.4 -0.6 -0.8 -1.0 -1.2 -40 VDD = 5V VREF = 4.096V -20 0 10 0 -10 -20 -30 -40 20 40 60 TEMPERATURE (C) 80 100 120 -50 -40 Figure 12. INL vs. Temperature VDD = 5V VREF = 4.096V -20 0 20 40 60 TEMPERATURE (C) 80 100 Figure 15. Zero-Code Error vs. Temperature Rev. A | Page 9 of 24 120 06845-116 ZERO-SCALE ERROR (V) 0.2 06845-113 INL (LSB) 0.4 AD5066 0.0020 7 0.0015 VDD = 5V DAC OUTPUT UNLOADED TA = 25C 6 0.0010 GAIN ERROR (%FSR) 5 HITS 0.0005 0 4 3 -0.0005 2 -0.0010 -20 0 1 20 40 60 TEMPERATURE (C) 80 100 120 0 2.45 Figure 16. Gain Error vs. Temperature 2.55 2.60 IDD POWER-UP (mA) 2.50 2.65 2.70 06845-120 -0.0020 -40 VDD = 5V VREF = 4.096V 06845-117 -0.0015 Figure 19. IDD Histogram VDD = 5.5 V 0.010 60 VDD = 5V TA = 25C DAC OUTPUT UNLOADED 50 +125C IDD POWERDOWN +25C IDD POWERDOWN -40C IDD POWERDOWN ERROR (%FSR) 0.005 40 HITS FULL-SCALE ERROR 0 30 20 GAIN ERROR -0.005 VDD = 5V VREF = 4.096V TA = 25C 2.7 3.2 3.7 4.2 VDD (V) 4.7 0 06845-118 -0.010 5.2 0.2 Figure 17. Gain Error and Full-Scale Error vs. Supply Voltage 0.4 0.6 0.8 IDD POWERDOWN (A) 1.0 06845-139 10 Figure 20. IDD Power-Down Histogram 20 5 4 IDD (mA) 15 10 3 2 VDD = 5V VREF = 4.096V TA = 25C 1 0 2.7 3.7 4.7 VDD (V) 0 0 Figure 18. Zero-Code Error vs. Supply Voltage 10,000 20,000 30,000 40,000 DAC CODE Figure 21. IDD vs. Code Rev. A | Page 10 of 24 50,000 60,000 06845-121 5 06845-119 ZERO-SCALE Error (V) VDD = 5.5V VREF = 4.096V TA = 25C AD5066 1/4 TO 3/4 3.0 OUTPUT VOLTAGE (V) 4 IDD (mA) 3.5 VDD = 5.5V VREF = 4.096V TA = 25C CODE = MIDSCALE 3 2 2.5 2.0 1.5 3/4 TO 1/4 1.0 VDD = 4.5V VREF = 4.096V OUTPUT AMPLIFIER = AD797 TA = 25C DAC LOAD = 9pF 1 0.5 -20 0 20 40 60 TEMPERATURE (C) 80 100 120 0 06845-122 0 -40 0 1 2 Figure 22. IDD vs. Temperature 3 4 5 6 TIME (s) 7 8 9 10 Figure 25. Settling Time 5 VREF = 4.096V TA = 25C CODE = MIDSCALE VDD IDD (mA) 4 VREF 3 2 VOUT 1 3.0 3.5 4.0 4.5 SUPPLY VOLTAGE (V) 5.0 5.5 CH1 2.00V CH3 2.00V CH2 2.00V M10.00ms T 30.20% A CH1 640mV 06845-126 0 2.7 06845-123 VREF = 4.096V TA = 25C Figure 26. POR to 0 V Figure 23. IDD vs. Supply Voltage 10 VDD = 5.5V VREF = 4.096V TA = 25C VDD 8 4 VOUT 2 0 0 1 2 3 4 DIGITAL INPUT VOLTAGE (V) 5 6 CH1 2.00V CH3 2.00V CH2 2.00V M10.00ms T 30.20% Figure 27. POR to MS Figure 24. IDD vs. Digital Input Voltage Rev. A | Page 11 of 24 A CH1 640mV 06845-127 VDD = 5.5V VREF = 4.096V 06845-124 IDD (mA) VREF 6 06845-125 5 AD5066 15 CH1 = SCLK VDD = 5V VREF = 4.096V TA = 25C 10 CH2 = VOUT GLITCH AMPLITUDE (mV) 1 VDD = 5V POWER-UP TO MIDSCALE OUTPUT UNLOADED 2 5 0 -5 CH2 500mV M2s T 55% A CH2 1.2V -15 -2 06845-128 CH1 5V 0 2 Figure 28. Exiting PD to MS 4 TIME (s) 6 8 Figure 31. Digital Crosstalk 20 15 VDD = 5V VREF = 4.096V TA = 25C 15 GLITCH AMPLITUDE (mV) 5 0 -5 2 4 TIME (s) 6 5 0 -5 -10 -15 8 10 -20 -2 0 Figure 29. Glitch 6 8 10 4 VDD = 5V VREF = 4.096V TA = 25C 3 OUTPUT VOLTAGE (V) 10 5 0 -5 2 1 0 -1 -2 -10 VDD = 5V VREF = 4.096V TA = 25C -3 0 2 4 6 TIME (s) 8 10 06845-130 GLITCH AMPLITUDE (mV) 4 TIME (s) Figure 32. DAC-to-DAC Crosstalk 15 -15 -2 2 06845-132 0 10 Figure 30. Analog Crosstalk -4 0 1 2 3 4 5 6 Time (Seconds) Figure 33. 1/f Noise Rev. A | Page 12 of 24 7 8 9 10 06845-133 -15 -2 VDD = 5V VREF = 4.096V TA = 25C CODE = 0x8000 TO 0x7FFF OUTPUT UNLOADED WITH 5k AND 200pF 06845-129 GLITCH AMPLITUDE (mV) 10 -10 10 06845-131 -10 AD5066 0 VDD = 5V, TA = 25C DAC LOADED WITH MIDSCALE VREF = 3.0V 200mV p-p -10 -20 CH1 PEAK TO PEAK 155mV VOUT VOUT LEVEL (dB) -30 -40 -50 -60 LAST SCLK -70 -80 -100 5 20 10 50 30 40 FREQUENCY (kHz) CH1 50.0mV 55 Figure 34. Total Harmonic Distortion CH2 5.00V M4.00s T 9.800% A CH2 1.80V 06845-137 VDD = 5V VREF = 4.096V TA = 25C 06845-016 -90 Figure 37. Glitch Upon Entering Power Down CH1 PEAK TO PEAK 159mV CLR VOUT VOUT LAST SCLK CH2 2.00V M2.00ms T 10.20% A CH1 1.80V CH1 50.0mV Figure 35. Hardware CLR 2.8 1/4 TO 3/4 2.4 2.2 2.0 1.8 3/4 TO 1/4 1.6 VDD = 4.5V VREF = 4.096V TA = 25C 1.0 1.5 1.6 1.7 1.8 1.9 2 2.1 TIME (s) 2.2 2.3 2.4 06845-136 OUTPUT VOLTAGE (V) 2.6 1.2 M4.00s T 9.800% A CH2 Figure 38. Glitch Upon Exiting Power Down 3.0 1.4 CH2 5.00V Figure 36. Slew Rate Rev. A | Page 13 of 24 1.80V 06845-138 CH1 5.00V 06845-135 VDD = 5V VREF = 4.096V TA = 25C AD5066 TERMINOLOGY Relative Accuracy or Integral Nonlinearity (INL) Relative accuracy or INL is a measure of the maximum deviation in LSBs from a straight line passing through the endpoints of the DAC transfer function. Figure 4, Figure 5, and Figure 6 show typical INL vs. code plots. Differential Nonlinearity (DNL) DNL is the difference between the measured change and the ideal 1 LSB change between any two adjacent codes. A specified differential nonlinearity of 1 LSB maximum ensures monotonicity. Figure 7, Figure 8, and Figure 9 show typical DNL vs. code plots. DC Crosstalk DC crosstalk is the dc change in the output level of one DAC in response to a change in the output of another DAC. It is measured with a full-scale output change on one DAC (or soft power-down and power-up) while monitoring another DAC kept at midscale. It is expressed in microvolts. Reference Feedthrough Reference feedthrough is the ratio of the amplitude of the signal at the DAC output to the reference input when the DAC output is not being updated (that is, LDAC is high). It is expressed in decibels. Zero-Code Error Zero-code error is a measure of the output error when zero code (0x0000) is loaded into the DAC register. Ideally, the output should be 0 V. The zero-code error is always positive in the AD5066, because the output of the DAC cannot go below 0 V. Zero-code error is expressed in millivolts. Figure 17 shows a typical zero-code error vs. supply voltage plot. Digital Feedthrough Digital feedthrough is a measure of the impulse injected into the analog output of a DAC from the digital input pins of the device but is measured when the DAC is not being written to (SYNC held high). It is specified in nanovolts per second and measured with one simultaneous DIN and SCLK pulse loaded to the DAC. Gain Error Gain error is a measure of the span error of the DAC. It is the deviation in slope of the DAC transfer characteristic from the ideal, expressed as a percentage of the full-scale range. Digital Crosstalk Digital crosstalk is the glitch impulse transferred to the output of one DAC at midscale in response to a full-scale code change (all 0s to all 1s or vice versa) in the input register of another DAC. It is measured in standalone mode and is expressed in nanovolts per second. Gain Error Drift Gain error drift is a measure of the change in gain error with changes in temperature. It is expressed in (ppm of full-scale range)/C. Zero-Code Error Drift Zero-code error drift is a measure of the change in zero-code error with a change in temperature. It is expressed in microvolts per degrees Celsius. Full-Scale Error Full-scale error is a measure of the output error when a fullscale code (0xFFFF) is loaded into the DAC register. Ideally, the output should be VREF - 1 LSB. Full-scale error is expressed as a percentage of the full-scale range. Digital-to-Analog Glitch Impulse Digital-to-analog glitch impulse is the impulse injected into the analog output when the input code in the DAC register changes state. It is normally specified as the area of the glitch in nanovolts per second and is measured when the digital input code is changed by 1 LSB at the major carry transition (0x7FFF to 0x8000). See Figure 28. DC Power Supply Rejection Ratio (PSRR) DC PSRR indicates how the output of the DAC is affected by changes in the supply voltage. DC PSRR is the ratio of the change in VOUT to a change in VDD for full-scale output of the DAC. It is measured in decibels. Analog Crosstalk Analog crosstalk is the glitch impulse transferred to the output of one DAC due to a change in the output of another DAC. It is measured by loading one of the input registers with a full-scale code change (all 0s to all 1s or vice versa) while keeping LDAC high and then pulsing LDAC low and monitoring the output of the DAC whose digital code has not changed. The area of the glitch is expressed in nanovolts per second. DAC-to-DAC Crosstalk DAC-to-DAC crosstalk is the glitch impulse transferred to the output of one DAC due to a digital code change and subsequent output change of another DAC. This includes both digital and analog crosstalk. It is measured by loading one of the DACs with a full-scale code change (all 0s to all 1s or vice versa) with LDAC low and monitoring the output of another DAC. The energy of the glitch is expressed in nanovolts per second. Total Harmonic Distortion (THD) THD is the difference between an ideal sine wave and its attenuated version using the DAC. The sine wave is used as the reference for the DAC, and the THD is a measure of the harmonics present on the DAC output. It is measured in decibels. Rev. A | Page 14 of 24 AD5066 THEORY OF OPERATION DIGITAL-TO-ANALOG CONVERTER SERIAL INTERFACE The AD5066 is a quad 16-bit, serial input, voltage output nanoDAC. The part operates from supply voltages of 2.7 V to 5.5 V. Data is written to the AD5066 in a 32-bit word format via a 3-wire serial interface. The AD5066 incorporates a power-on reset circuit to ensure the DAC output powers up to a known output state. The devices also have a software power-down mode that reduces the typical current consumption to typically 400 nA. The AD5066 has a 3-wire serial interface (SYNC, SCLK, and DIN) that is compatible with SPI, QSPI, MICROWIRE, and most DSP interface standards. See Figure 2 for a timing diagram of a typical write sequence. Because the input coding to the DAC is straight binary, the ideal output voltage when using an external reference is given by D VOUT VREFIN N 2 where: D is the decimal equivalent of the binary code that is loaded to the DAC register (0 to 65,535). N is the DAC resolution. DAC ARCHITECTURE The DAC architecture of the AD5066 consists of two matched DAC sections. A simplified circuit diagram is shown in Figure 39. The four MSBs of the 16-bit data word are decoded to drive 15 switches, E1 to E15. Each of these switches connects one of 15 matched resistors to either GND or the VREF buffer output. The remaining 12 bits of the data word drive the S0 to S11 switches of a 12-bit voltage mode R-2R ladder network. VOUT 2R 2R 2R 2R 2R 2R 2R S0 S1 S11 E1 E2 E15 12-BIT R-2R LADDER FOUR MSBs DECODED INTO 15 EQUAL SEGMENTS 06845-005 VREF INPUT SHIFT REGISTER The input shift register is 32 bits wide (see Figure 40). The first four bits are don't cares. The next four bits are the command bits, C3 to C0 (see Table 7), followed by the 4-bit DAC address bits, A3 to A0 (see Table 8), and finally the bit data-word. The data-word comprises of a 16-bit input code followed by four don't care bits (see Figure 40). These data bits are transferred to the Input register on the 32nd falling edge of SCLK. Commands can be executed on individually selected DAC channels or on all DACs. Table 7. Command Definitions C3 0 0 Command C2 C1 C0 0 0 0 0 0 1 0 0 1 0 0 0 1 1 0 0 0 0 1 1 1 1 1 1 1 0 0 1 0 0 1 1 0 0 1 0 1 0 1 0 1 1 Description Write to Input Register n Transfer contents of Input Register n to DAC Register n Write to Input Register n and update all DAC Registers Write to Input Register n and update DAC Register n Power down/power up DAC Load clear code register Load LDAC register Reset (power-on reset) Reserved Reserved Reserved Table 8. DAC Input Register Address Bits Figure 39. DAC Ladder Structure REFERENCE BUFFER The AD5066 operates with an external reference. Each of the four on-board DACs has a dedicated voltage reference pin that is buffered. The reference input pin has an input range of 2 V to VDD - 0.4 V. This input voltage is then used to provide a buffered reference for the DAC core. A3 0 0 0 0 1 Address (n) A2 A1 0 0 0 0 0 1 0 1 1 1 A0 0 1 0 1 1 Selected DAC Channel DAC A DAC B DAC C DAC D All DACs DB31 (MSB) X X X C3 C2 C1 C0 A3 A2 A1 A0 DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 X X X X DATA BITS COMMAND BITS 06845-007 X DB0 (LSB) ADDRESS BITS Figure 40. Input Shift Register Content Rev. A | Page 15 of 24 AD5066 When Bit DB9 and Bit DB8 in the control register are set to 0, the part is configured in normal mode with its normal power consumption of 2.5 mA at 5 V. However, for the three powerdown modes, the supply current falls to 0.4 A if all the channels are powered down. Not only does the supply current fall, but the output pin is also internally switched from the output of the DAC to a resistor network of known values. This has the advantage that the output impedance of the part is known while the part is in power-down mode. There are three different options: the output is connected internally to GND through either a 1 k or a 100 k resistor, or it is left open-circuited (three-state). The output stage is illustrated in Figure 41. DAC SYNC Interrupt In a normal write sequence, the SYNC line is kept low for at least 32 falling edges of SCLK, and the DAC is updated on the 32nd falling edge. However, if SYNC is brought high before the 32nd falling edge, this acts as an interrupt to the write sequence. The input shift register is reset, and the write sequence is seen as invalid. Neither an update of the DAC register contents nor a change in the operating mode occurs (see Figure 42). Power-Down Modes The AD5066 can be configured through software, in one of four different modes: normal mode (default) and three separate power-down modes (see Table 9). Any or all DACs can be powered down. Command 0100 is reserved for the powerdown function (see Table 7). These power-down modes are software-programmable by setting two bits, Bit DB9 and Bit DB8, in the input shift register. Table 9 shows how the state of the bits corresponds to the mode of operation of the device. Any or all DACs (DAC A to DAC D) can be powered down to the selected mode by setting the corresponding four bits (DB3, DB2, DB1, DB0) to 1. See Table 10 for the contents of the input shift register during power-down/power-up operation. VOUT POWER-DOWN CIRCUITRY RESISTOR NETWORK 06845-008 The write sequence begins by bringing the SYNC line low. Bringing the SYNC line low enables the DIN and SCLK input buffers. Data from the DIN line is clocked into the 32-bit shift register on the falling edge of SCLK. The serial clock frequency can be as high as 50 MHz, making the AD5066 compatible with high speed DSPs. On the 32nd falling clock edge, the last data bit is clocked in, and the programmed function is executed, that is, a change in the input register contents (see Table 8) and/or a change in the mode of operation. At this stage, the SYNC line can be kept low or be brought high. In either case, it must be brought high for a minimum of 2 s (single-channel update, see the t8 parameter in Table 4) before the next write sequence so that a falling edge of SYNC can initiate the next write sequence. Idle SYNC high between write sequences for even lower power operation of the part. Figure 41. Output Stage During Power-Down Mode The bias generator, DAC core, and other associated linear circuitry are shut down when all channels are powered down. However, the contents of the DAC register are unaffected when in power-down mode. The time to exit power-down mode is typically 2.9 s (see Figure 27). Table 9. Modes of Operation DB9 0 DB8 0 0 1 1 1 0 1 Operating Mode Normal operation Power-down modes 1 k to GND 100 k to GND Three-state SCLK SYNC DB31 DB31 DB0 INVALID WRITE SEQUENCE: SYNC HIGH BEFORE 32ND FALLING EDGE DB0 VALID WRITE SEQUENCE: OUTPUT UPDATES ON THE 32ND FALLING EDGE Figure 42. SYNC Interrupt Facility Rev. A | Page 16 of 24 06845-017 DIN AD5066 POWER-ON RESET where it is important to know the state of the output of the DAC while it is in the process of powering up. There is also a software executable reset function that resets the DAC to the power-on reset code. Command 0111 is reserved for this reset function (see Table 7). Any events on LDAC or CLR during power-on reset are ignored. The AD5066 contains a power-on reset circuit that controls the output voltage during power-up. By connecting the POR pin low, the AD5066 output powers up to 0 V; by connecting the POR pin high, the AD5066 output powers up to midscale. The output remains powered up at this level until a valid write sequence is made to the DAC. This is useful in applications Table 10. 32-Bit Input Shift Register Contents for Power-Up/Power-Down Function MSB DB31 to DB28 X Don't cares LSB DB27 DB26 DB25 DB24 0 1 0 0 Command bits (C2 to C0) DB23 to DB20 X Address bits (A3 to A0)-- don't cares DB10 to DB19 X Don't cares DB9 DB8 PD1 PD0 Power-down mode Rev. A | Page 17 of 24 DB4 to DB7 X Don't cares DB3 DB2 DB1 DB0 DAC D DAC C DAC B DAC A Power-down/power-up channel selection--set bit to 1 to select AD5066 CLEAR CODE REGISTER The AD5066 has a hardware CLR pin that is an asynchronous clear input. The CLR input is falling edge sensitive. Bringing the CLR line low clears the contents of the input register and the DAC registers to the data contained in the user-configurable CLR register and sets the analog outputs accordingly (see Table 11). This function can be used in system calibration to load zero scale, midscale, or full scale to all channels together. These clear code values are user-programmable by setting two bits, Bit DB1 and Bit DB0, in the control register (see Table 11). The default setting clears the outputs to 0 V. Command 0101 is reserved for loading the clear code register (see Table 7). Table 11. Clear Code Register DB1 (CR1) 0 0 1 1 DB0 (CR0) 0 1 0 1 Clears to Code 0x0000 0x8000 0xFFFF No operation The part exits clear code mode on the 32nd falling edge of the next write to the part. If CLR is activated during a write sequence, the write is aborted. The CLR pulse activation time (the falling edge of CLR to when the output starts to change) is typically 10.6 s. See Table 13 for contents of the input shift register during the loading clear code register operation. LDAC FUNCTION Hardware LDAC Pin Synchronous LDAC: LDAC is held permanently low. After new data is read, the DAC registers are updated on the falling edge of the 32nd SCLK pulse, provided LDAC is held low. Asynchronous LDAC: LDAC is held high then pulsed low to update. The outputs are not updated at the same time that the input registers are written to. When LDAC is pulsed low, the DAC registers are updated with the contents of the input registers. Command 0001, 0010 and 0011 (see Table 7) update the DAC Register/Registers, regardless of the level of the LDAC pin Software LDAC Function Writing to the DAC using Command 0110 loads the 4-bit LDAC register (DB3 to DB0). The default for each channel is 0; that is, the LDAC pin works normally. Setting the bits to 1 updates the DAC channel regardless of the state of the hardware LDAC pin, so that it effectively sees the hardware LDAC pin as being tied low (see Table 12 for the LDAC register mode of operation.) This flexibility is useful in applications where the user wants to simultaneously update select channels while the remainder of the channels are synchronously updating. Table 12. Load LDAC Register LDAC Bits (DB3 to DB0) 0 1 1 The outputs of all DACs can be updated simultaneously using the hardware LDAC pin, as shown in Figure 2. There are two methods of using the hardware LDAC pin: synchronously (LDAC permanently low) and asynchronously (LDAC pulsed). LDAC Pin 1/0 X1 LDAC Operation Determined by LDAC pin DAC channels update, overrides the LDAC pin; DAC channels see LDAC as 0 X = don't care. The LDAC register gives the user extra flexibility and control over the hardware LDAC pin (see Table 14). Setting the LDAC bits (DB0 to DB3) to 0 for a DAC channel means that this channel's update is controlled by the hardware LDAC pin. Table 13. 32-Bit Input Shift Register Contents for Clear Code Function MSB DB31 to DB28 X Don't cares DB27 DB26 DB25 DB24 0 1 0 1 Command bits (C3 to C0) DB23 X DB22 DB21 DB20 X X X Address bits (A3 to A0) DB2 to DB19 X Don't cares LSB DB1 DB0 1/0 1/0 Clear code register (CR1 to CR0) Table 14. 32-Bit Input Shift Register Contents for LDAC Overwrite Function MSB DB31 to DB28 X Don't cares LSB DB27 DB26 DB25 DB24 0 1 1 0 Command bits (C3 to C0) DB23 to DB20 X Address bits (A3 to A0)--don't cares Rev. A | Page 18 of 24 DB4 to DB19 X Don't cares DB3 DB2 DB1 DB0 DAC D DAC C DAC B DAC A Setting LDAC bit to 1 override LDAC pin AD5066 POWER SUPPLY BYPASSING AND GROUNDING AD5066 to 68HC11/68L11 Interface When accuracy is important in a circuit, it is helpful to carefully consider the power supply and ground return layout on the board. The printed circuit board containing the AD5066 should have separate analog and digital sections. If the AD5066 is in a system where other devices require an AGND-to-DGND connection, make the connection at one point only and as close as possible to the AD5066. Figure 44 shows a serial interface between the AD5066 and the 68HC11/68L11 microcontroller. SCK of the 68HC11/68L11 drives the SCLK of the AD5066, and the MOSI output drives DIN of the DAC. A port line (PC7) drives the SYNC signal. The power supply line should have as large a trace as possible to provide a low impedance path and reduce glitch effects on the supply line. Shield the clocks and other fast switching digital signals from other parts of the board by digital ground. Avoid crossover of digital and analog signals if possible. When traces cross on opposite sides of the board, ensure that they run at right angles to each other to reduce feedthrough effects through the board. The best board layout technique is the microstrip technique, where the component side of the board is dedicated to the ground plane only, and the signal traces are placed on the solder side. However, this is not always possible with a 2-layer board. AD5066* SYNC DIN SCLK *ADDITIONAL PINS OMITTED FOR CLARITY. SCLK DIN The setup conditions for correct operation of this interface are as follows: The 68HC11/68L11 is configured with its CPOL bit as 0, and the CPHA bit as 1. When data is being transmitted to the DAC, the SYNC line is taken low (PC7). When the 68HC11/ 68L11 is configured as described previously, data appearing on the MOSI output is valid on the falling edge of SCK. Serial data from the 68HC11/68L11 is transmitted in 8-bit bytes with only eight falling clock edges occurring in the transmit cycle. Data is transmitted MSB first. To load data to the AD5066, PC7 is left low after the first eight bits are transferred, and a second serial write operation is performed to the DAC. PC7 is taken high at the end of this procedure. 06845-009 TSCLK0 SCK Figure 44. AD5066 to 68HC11/68L11 Interface Figure 43 shows a serial interface between the AD5066 and the Blackfin ADSP-BF53x microprocessor. The ADSP-BF53x processor family incorporates two dual-channel synchronous serial ports, SPORT1 and SPORT0, for serial and multiprocessor communications. Using SPORT0 to connect to the AD5066, the setup for the interface is as follows: DT0PRI drives the DIN pin of the AD5066, TSCLK0 drives the SCLK of the parts, and TFS0 drives SYNC. DT0PRI SYNC *ADDITIONAL PINS OMITTED FOR CLARITY. AD5066 to Blackfin(R) ADSP-BF53X Interface TFS0 PC7 MOSI MICROPROCESSOR INTERFACING ADSP-BF53x* AD5066* 06845-010 Bypass the power supply to the AD5066 with 10 F and 0.1 F capacitors. The capacitors should be physically as close as possible to the device, with the 0.1 F capacitor, ideally, right up against the device. The 10 F capacitors are the tantalum bead type. It is important that the 0.1 F capacitor has low effective series resistance and low effective series inductance, typical of common ceramic types of capacitors. This 0.1 F capacitor provides a low impedance path to ground for high frequencies caused by transient currents due to internal logic switching. 68HC11/68L11* Figure 43. AD5066 to Blackfin ADSP-BF53X Interface Rev. A | Page 19 of 24 AD5066 80C51/80L51* AD5066* P3.3 SYNC TxD SCLK RxD DIN *ADDITIONAL PINS OMITTED FOR CLARITY. Figure 45. AD5066 to 80C512/80L51 Interface AD5066 to MICROWIRE Interface Figure 46 shows an interface between the AD5066 and any MICROWIRE-compatible device. Serial data is clocked into the AD5066 on the falling edge of the SCLK. MICROWIRE* AD5066* CS SYNC SK DIN SO SCLK *ADDITIONAL PINS OMITTED FOR CLARITY. Figure 46. AD5066 to MICROWIRE Interface Rev. A | Page 20 of 24 06845-012 Figure 45 shows a serial interface between the AD5066 and the 80C51/80L51 microcontroller. The setup for the interface is as follows: TxD of the 80C51/80L51 drives SCLK of the AD5066, RxD drives DIN on the AD5066, and a bit-programmable pin on the port (P3.3) drives the SYNC signal. When data is to be transmitted to the AD5066, P3.3 is taken low. The 80C51/80L51 transmit data in 8-bit bytes only; thus, only eight falling clock edges occur in the transmit cycle. To load data to the DAC, P3.3 is left low after the first eight bits are transmitted, and a second, third, and fourth write cycle is initiated to transmit the second, third, and fourth byte of data. P3.3 is taken high following the completion of this cycle. The 80C51/80L51 output the serial data in a format that has the LSB first. The AD5066 must receive data with the MSB first. The 80C51/80L51 transmit routine should take this into account. 06845-011 AD5066 to 80C51/80L51 Interface AD5066 APPLICATIONS INFORMATION USING A REFERENCE AS A POWER SUPPLY R2 = 10k +5V R1 = 10k +5.5V +5V VREF VREF AD820/ OP295 5V VOUT VDD 10F 0.1F -5V AD5066 06845-014 Because the supply current required by the AD5066 is extremely low, an alternative option is to use a voltage reference to supply the required voltage to the parts (see Figure 47). This is especially useful if the power supply is quite noisy or if the system supply voltages are at some value other than 5 V or 3 V, for example, 15 V. The voltage reference outputs a steady supply voltage for the AD5066. If the low dropout REF195 is used, it must supply 2.5 mA of current to the AD5066 with no load on the output of the DAC. 3-WIRE SERIAL INTERFACE 15V Figure 48. Bipolar Operation with the AD5066 REF195 5V 4.5V VDD USING THE AD5066 WITH A GALVANICALLY ISOLATED INTERFACE VREF SYNC SCLK AD5066 VOUTx = 0V TO 4.5V DIN 06845-013 3-WIRE SERIAL INTERFACE REF194 Figure 47. REF195 as a Power Supply to the AD5066 BIPOLAR OPERATION The AD5066 has been designed for single-supply operation, but a bipolar output range is also possible using the circuit in Figure 48. The circuit gives an output voltage range of 5 V. Rail-to-rail operation at the amplifier output is achieved using an AD8638 or AD8639 the output amplifier. The output voltage for any input code can be calculated as follows: In process control applications in industrial environments, it is often necessary to use a galvanically isolated interface to protect and isolate the controlling circuitry from any hazardous common-mode voltages that can occur in the area where the DAC is functioning. iCoupler(R) provides isolation in excess of 2.5 kV. The AD5066 uses a 3-wire serial logic interface, so the ADuM1300 three-channel digital isolator provides the required isolation (see Figure 49). The power supply to the part also needs to be isolated, which is done by using a transformer. On the DAC side of the transformer, a 5 V regulator provides the 5 V supply required for the AD5066. 5V REGULATOR 10F POWER D R1 + R2 R2 VO = VDD x x - VDD x R1 65,536 R1 VDD SCLK VIA VOA SCLK ADuM1300 AD5066 SDI VIB VOB SYNC DATA VIC VOC DIN VOUTx GND 06845-015 where: D = the input code in decimal (0 to 65,535). VDD = 5 V. R1 = R2 = 10 k. 10 x D VO = -5V 65,536 0.1F This is an output voltage range of 5 V, with 0x0000 corresponding to a -5 V output, and 0xFFFF corresponding to a +5 V output. Figure 49. AD5066 with a Galvanically Isolated Interface Rev. A | Page 21 of 24 AD5066 OUTLINE DIMENSIONS 5.10 5.00 4.90 16 9 4.50 4.40 4.30 6.40 BSC 1 8 PIN 1 1.20 MAX 0.15 0.05 0.20 0.09 0.65 BSC 0.30 0.19 COPLANARITY 0.10 SEATING PLANE 0.75 0.60 0.45 8 0 COMPLIANT TO JEDEC STANDARDS MO-153-AB Figure 50. 16-Lead Thin Shrink Small Outline Package [TSSOP] (RU-16) Dimensions shown in millimeter ORDERING GUIDE Model1 AD5066BRUZ AD5066BRUZ-REEL7 AD5066ARUZ AD5066ARUZ-REEL7 1 Temperature Range -40C to +125C -40C to +125C -40C to +125C -40C to +125C Package Description 16-Lead TSSOP 16-Lead TSSOP 16-Lead TSSOP 16-Lead TSSOP Z = RoHS Compliant Part. Rev. A | Page 22 of 24 Package Option RU-16 RU-16 RU-16 RU-16 Power-On Reset to Code Zero Zero Zero Zero Accuracy 1 LSB INL 1 LSB INL 4 LSB INL 4 LSB INL Resolution 16 bits 16 bits 16 bits 16 bits AD5066 NOTES Rev. A | Page 23 of 24 AD5066 NOTES (c)2009-2010 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D06845-0-8/10(A) Rev. A | Page 24 of 24