(R) OPA OPA244 OPA2244 OPA4244 OPA 244 224 4 OPA OPA 244 (R) 424 OPA 4 224 4 MicroPower, Single-Supply OPERATIONAL AMPLIFIERS MicroAmplifier TM Series FEATURES DESCRIPTION MicroSIZE PACKAGES OPA244 (Single): SOT-23-5 OPA2244 (Dual): MSOP-8 OPA4244 (Quad): TSSOP-14 MicroPOWER: IQ = 50A/channel SINGLE SUPPLY OPERATION WIDE BANDWIDTH: 430kHz WIDE SUPPLY RANGE: Single Supply: 2.2V to 36V Dual Supply: 1.1V to 18V The OPA244 (single), OPA2244 (dual), and OPA4244 (quad) op amps are designed for very low quiescent current (50A/channel), yet achieve excellent bandwidth. Ideal for battery powered and portable instrumentation, all versions are offered in micro packages for space-limited applications. The dual and quad versions feature completely independent circuitry for lowest crosstalk and freedom from interaction, even when overdriven or overloaded. The OPA244 series is easy to use and free from phase inversion and overload problems found in some other op amps. These amplifiers are stable in unity gain and excellent performance is maintained as they swing to their specified limits. They can be operated from single (+2.2V to +36V) or dual supplies (1.1V to 18V). The input common-mode voltage range includes ground--ideal for many single supply applications. All versions have similar performance. However, there are some differences, such as common-mode rejection. All versions are interchangeable in most applications. All versions are offered in miniature, surface-mount packages. OPA244 (single version) comes in the tiny 5-lead SOT-23-5 surface mount, SO-8 surface mount, and 8-pin DIP. OPA2244 (dual version) is available in the MSOP-8 surface mount, SO-8 surface-mount, and 8-pin DIP. The OPA4244 (quad) comes in the TSSOP-14 surface mount. They are fully specified from -40C to +85C and operate from -55C to +125C. A SPICE Macromodel is available for design analysis. APPLICATIONS BATTERY POWERED SYSTEMS PORTABLE EQUIPMENT PCMCIA CARDS BATTERY PACKS AND POWER SUPPLIES CONSUMER PRODUCTS OPA244 Out 1 5 V+ 4 -In V- 2 +In 3 OPA4244 SOT-23-5 OPA2244 OPA244 NC 1 8 NC Out A 1 -In 2 7 V+ -In A 2 +In 3 6 Output +In A 3 V- 4 5 NC V- 4 8-Pin DIP, SO-8 A B 8 V+ 7 Out B 6 -In B 5 +In B 8-Pin DIP, SO-8, MSOP-8 Output A 1 14 Output D -Input A 2 13 -Input D +Input A 3 12 +Input D +V 4 11 -V +Input B 5 10 +Input C -Input B 6 9 -Input C Output B 7 8 Output C TSSOP-14 International Airport Industrial Park * Mailing Address: PO Box 11400, Tucson, AZ 85734 * Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 * Tel: (520) 746-1111 Twx: 910-952-1111 * Internet: http://www.burr-brown.com/ * Cable: BBRCORP * Telex: 066-6491 * FAX: (520) 889-1510 * Immediate Product Info: (800) 548-6132 (c) 1999 Burr-Brown Corporation SBOS088 PDS-1437C Printed in U.S.A. December, 1999 SPECIFICATIONS: VS = +2.6V to +36V Boldface limits apply over the specified temperature range, TA = -40C to +85C At TA = +25C, RL = 20k connected to ground, unless otherwise noted. OPA244NA, PA, UA PARAMETER CONDITION OFFSET VOLTAGE Input Offset Voltage TA = -40C to 85C vs Temperature vs Power Supply TA = -40C to 85C OUTPUT Voltage Output, Positive TA = -40C to 85C Voltage Output, Negative TA = -40C to 85C Voltage Output, Positive TA = -40C to 85C Voltage Output, Negative TA = -40C to 85C Short-Circuit Current Capacitive Load Drive POWER SUPPLY Specified Voltage Range Minimum Operating Voltage Quiescent Current TA = -40C to 85C TEMPERATURE RANGE Specified Range Operating Range Storage Range Thermal Resistance SOT-23-5 Surface-Mount SO-8 Surface-Mount 8-Pin DIP UNITS 1.5 2 0.7 dVOS/dT PSRR TA = -40C to 85C VS = +2.6V to +36V VS = +2.6V to +36V 4 5 50 50 mV mV V/C V/V V/V VCM = VS /2 VCM = VS /2 -10 1 -25 10 nA nA IB IOS VCM CMRR VS = 18V, VCM = -18V to +17.1V VS = 18V, VCM = -18V to +17.1V VO = 0.5V to (V+) - 0.9 VO = 0.5V to (V+) - 0.9 AOL GBW SR VO Vp-p nV/Hz fA/Hz 0.4 22 40 en in 0 84 84 INPUT IMPEDANCE Differential Common-Mode FREQUENCY RESPONSE Gain-Bandwidth Product Slew Rate Settling Time 0.01% Overload Recovery Time MAX VS = 7.5V, VCM = 0 NOISE Input Voltage Noise, f = 0.1kHz to 10kHz Input Voltage Noise Density, f = 1kHz Current Noise Density, f = 1kHz OPEN-LOOP GAIN Open-Loop Voltage Gain TA = -40C to 85C TYP(1) VOS INPUT BIAS CURRENT Input Bias Current Input Offset Current INPUT VOLTAGE RANGE Common-Mode Voltage Range Common-Mode Rejection TA = -40C to 85C MIN 86 86 G=1 10V Step VIN * Gain = VS AOL 80dB, RL = 20k to VS/2 AOL 80dB, RL = 20k to VS/2 AOL 80dB, RL = 20k to VS/2 AOL 80dB, RL = 20k to VS/2 AOL 80dB, RL = 20k to Ground AOL 80dB, RL = 20k to Ground AOL 80dB, RL = 20k to Ground AOL 80dB, RL = 20k to Ground (V+) - 0.9 (V+) - 0.9 0.5 0.5 TA = -40C to 85C +2.6 ISC CLOAD VS IQ 98 (V+) - 0.9 V dB dB 106 || 2 109 || 2 || pF || pF 106 dB dB 430 -0.1/+0.16 150 8 kHz V/s s s (V+) - 0.75 (V+) - 0.75 0.2 0.2 (V+) - 0.75 (V+) - 0.75 0.1 0.1 -25/+12 See Typical Curve V V V V V V V V mA +36 +2.2 50 IO = 0 IO = 0 -40 -55 -65 JA 200 150 100 60 70 V V A A 85 125 150 C C C C/W C/W C/W NOTE: (1) VS = +15V. The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user's own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support devices and/or systems. (R) OPA244, 2244, 4244 2 SPECIFICATIONS: VS = +2.6V to +36V Boldface limits apply over the specified temperature range, TA = -40C to +85C At TA = +25C, RL = 20k connected to ground, unless otherwise noted. OPA2244EA, PA, UA PARAMETER OFFSET VOLTAGE Input Offset Voltage TA = -40C to 85C vs Temperature vs Power Supply TA = -40C to 85C Channel Separation CONDITION OUTPUT Voltage Output, Positive TA = -40C to 85C Voltage Output, Negative TA = -40C to 85C Voltage Output, Positive TA = -40C to 85C Voltage Output, Negative TA = -40C to 85C Short-Circuit Current Capacitive Load Drive POWER SUPPLY Specified Voltage Range Minimum Operating Voltage Quiescent Current (per amplifier) TA = -40C to 85C TEMPERATURE RANGE Specified Range Operating Range Storage Range Thermal Resistance MSOP-8 Surface-Mount SO-8 Surface-Mount 8-Pin DIP UNITS 1.5 2 mV mV V/C V/V V/V dB 0.7 dVOS/dT PSRR TA = -40C to 85C VS = +2.6V to +36V VS = +2.6V to +36V 4 5 50 50 140 IB IOS VCM = VS /2 VCM = VS /2 -10 1 VCM CMRR AOL GBW SR VO VS = 18V, VCM = -18V to +17.1V VS = 18V, VCM = -18V to +17.1V 0 72 72 VO = 0.5V to (V+) - 0.9 VO = 0.5V to (V+) - 0.9 86 86 G=1 10V Step VIN * Gain = VS AOL 80dB, RL = 20k to VS/2 AOL 80dB, RL = 20k to VS/2 AOL 80dB, RL = 20k to VS/2 AOL 80dB, RL = 20k to VS/2 AOL 80dB, RL = 20k to Ground AOL 80dB, RL = 20k to Ground AOL 80dB, RL = 20k to Ground AOL 80dB, RL = 20k to Ground (V+) - 0.9 (V+) - 0.9 0.5 0.5 TA = -40C to 85C +2.6 ISC CLOAD VS IQ -25 10 98 (V+) - 0.9 V dB dB 106 || 2 109 || 2 || pF || pF 106 dB dB 430 -0.1/+0.16 150 8 kHz V/s s s (V+) - 0.75 (V+) - 0.75 0.2 0.2 (V+) - 0.75 (V+) - 0.75 0.1 0.1 -25/+12 See Typical Curve V V V V V V V V mA +36 +2.2 40 IO = 0 IO = 0 nA nA Vp-p nV/Hz fA/Hz 0.4 22 40 en in INPUT IMPEDANCE Differential Common-Mode FREQUENCY RESPONSE Gain-Bandwidth Product Slew Rate Settling Time 0.01% Overload Recovery Time MAX VS = 7.5V, V CM = 0 NOISE Input Voltage Noise, f = 0.1kHz to 10kHz Input Voltage Noise Density, f = 1kHz Current Noise Density, f = 1kHz OPEN-LOOP GAIN Open-Loop Voltage Gain TA = -40C to 85C TYP(1) VOS INPUT BIAS CURRENT Input Bias Current Input Offset Current INPUT VOLTAGE RANGE Common-Mode Voltage Range Common-Mode Rejection TA = -40C to 85C MIN -40 -55 -65 50 63 V V A A 85 125 150 C C C JA 200 150 100 C/W C/W C/W NOTE: (1) VS = +15V. (R) 3 OPA244, 2244, 4244 SPECIFICATIONS: VS = +2.6V to +36V Boldface limits apply over the specified temperature range, TA = -40C to +85C At TA = +25C, RL = 20k connected to ground, unless otherwise noted. OPA4244EA PARAMETER CONDITION OFFSET VOLTAGE Input Offset Voltage TA = -40C to 85C vs Temperature vs Power Supply TA = -40C to 85C Channel Separation OUTPUT Voltage Output, Positive TA = -40C to 85C Voltage Output, Negative TA = -40C to 85C Voltage Output, Positive TA = -40C to 85C Voltage Output, Negative TA = -40C to 85C Short-Circuit Current Capacitive Load Drive POWER SUPPLY Specified Voltage Range Minimum Operating Voltage Quiescent Current (per amplifier) TA = -40C to 85C TEMPERATURE RANGE Specified Range Operating Range Storage Range Thermal Resistance TSSOP-14 Surface Mount UNITS 1.5 2 mV mV V/C V/V V/V dB 0.7 dVOS/dT PSRR TA = -40C to 85C VS = +2.6V to +36V VS = +2.6V to +36V 4 5 50 50 140 VCM = VS /2 VCM = VS /2 IB IOS -10 1 VCM CMRR VS = 18V, VCM = -18V to +17.1V VS = 18V, VCM = -18V to +17.1V VO = 0.5V to (V+) - 0.9 VO = 0.5V to (V+) - 0.9 AOL GBW SR VO -25 10 0 82 82 86 86 G=1 10V Step VIN * Gain = VS AOL 80dB, RL = 20k to VS/2 AOL 80dB, RL = 20k to VS/2 AOL 80dB, RL = 20k to VS/2 AOL 80dB, RL = 20k to VS/2 AOL 80dB, RL = 20k to Ground AOL 80dB, RL = 20k to Ground AOL 80dB, RL = 20k to Ground AOL 80dB, RL = 20k to Ground (V+) - 0.9 (V+) - 0.9 0.5 0.5 TA = -40C to 85C +2.6 ISC CLOAD VS IQ 104 (V+) - 0.9 V dB dB 106 || 2 109 || 2 || pF || pF 106 dB dB 430 -0.1/+0.16 150 8 kHz V/s s s (V+) - 0.75 (V+) - 0.75 0.2 0.2 (V+) - 0.75 (V+) - 0.75 0.1 0.1 -25/+12 See Typical Curve V V V V V V V V mA +36 +2.2 40 IO = 0 IO = 0 -40 -55 -65 JA 100 NOTE: (1) VS = +15V. (R) OPA244, 2244, 4244 4 nA nA Vp-p nV/Hz fA/Hz 0.4 22 40 en in INPUT IMPEDANCE Differential Common-Mode FREQUENCY RESPONSE Gain-Bandwidth Product Slew Rate Settling Time 0.01% Overload Recovery Time MAX VS = 7.5V, VCM = 0 NOISE Input Voltage Noise, f = 0.1kHz to 10kHz Input Voltage Noise Density, f = 1kHz Current Noise Density, f = 1kHz OPEN-LOOP GAIN Open-Loop Voltage Gain TA = -40C to 85C TYP(1) VOS INPUT BIAS CURRENT Input Bias Current Input Offset Current INPUT VOLTAGE RANGE Common-Mode Voltage Range Common-Mode Rejection TA = -40C to 85C MIN 60 70 V V A A 85 125 150 C C C C/W ABSOLUTE MAXIMUM RATINGS(1) ELECTROSTATIC DISCHARGE SENSITIVITY Supply Voltage, V+ to V- .................................................................... 36V Input Voltage Range(2) ................................... (V-) - 0.3V to (V+) + 0.3V Input Current(2) ................................................................................. 10mA Output Short-Circuit(3) .............................................................. Continuous Operating Temperature .................................................. -55C to +125C Storage Temperature ..................................................... -65C to +150C Junction Temperature ...................................................................... 150C Lead Temperature (soldering, 10s) ................................................. 300C ESD Capability ................................................................................ 2000V This integrated circuit can be damaged by ESD. Burr-Brown recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. NOTES: (1) Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. (2) Inputs are diode-clamped to the supply rails and should be current-limited to 10mA or less if input voltages can exceed rails by more than 0.3V. (3) Short-circuit to ground, one amplifier per package. PACKAGE /ORDERING INFORMATION PRODUCT PACKAGE PACKAGE DRAWING NUMBER Single OPA244NA SOT-23-5 Surface-Mount 331 -40C to +85C A44 " " " " 8-Pin DIP SO-8 Surface-Mount 006 182 -40C to +85C -40C to +85C OPA244PA OPA244UA " OPA244PA OPA244UA SPECIFIED TEMPERATURE RANGE PACKAGE MARKING ORDERING NUMBER(1) TRANSPORT MEDIA OPA244NA/250 OPA244NA/3K OPA244PA OPA244UA OPA244UA/2K5 Tape and Reel Tape and Reel Rails Rails Tape and Reel OPA2244EA/250 OPA2244EA/2K5 OPA2244PA OPA2244UA OPA2244UA/2K5 Tape and Reel Tape and Reel Rails Rails Tape and Reel OPA4244EA/250 OPA4244EA/2K5 Tape and Reel Tape and Reel " " " " " Dual OPA2244EA MSOP-8 Surface-Mount 337 -40C to +85C A44 " " " " " OPA2244PA OPA2244UA 8-Pin DIP SO-8 Surface-Mount 006 182 -40C to +85C -40C to +85C OPA2244PA OPA2244UA " " " " " Quad OPA4244EA TSSOP-14 Surface-Mount 357 -40C to +85C OPA4244EA " " " " " NOTE: (1) Products followed by a slash (/) are only available in Tape and Reel in the quantities indicated (e.g., /250 indicates 250 devices per reel). Ordering 3000 pieces of "OPA244NA/3K" will get a single 3000 piece Tape and Reel. (R) 5 OPA244, 2244, 4244 TYPICAL PERFORMANCE CURVES At TA = 25C, VS = +15V, and RL = 20k connected to Ground, unless otherwise noted. CHANNEL SEPARATION OPEN-LOOP GAIN AND PHASE vs FREQUENCY 180 160 140 120 -60 130 Phase 100 -80 -100 80 60 -120 Gain Separation (dB) 150 -40 All Models Phase() -20 140 160 AOL (dB) 0 120 -140 20 -160 80 0 -180 70 -20 -200 60 10 100 10k 1k 100k OPA4244 100 40 1 OPA244 110 OPA2244 90 1M 1 10 100 10k 1k 100k Frequency (Hz) Frequency (Hz) POWER SUPPLY AND COMMON-MODE REJECTION vs FREQUENCY 110 120 100 110 100 90 PSRR, CMRR (dB) PSRR, CMRR (dB) OPA244 80 OPA2244 CMRR 70 OPA4244 60 50 90 80 CMRR 70 60 50 40 PSRR PSRR 40 30 30 10 100 1k 10k 100k 1 1M 10 100 OPEN-LOOP GAIN vs LOAD RESISTANCE 100k 1M OUTPUT VOLTAGE SWING vs OUTPUT CURRENT 15 120 VO = 5V Output Voltage Swing (V) 110 100 Gain(dB) 10k 1k Frequency (Hz) Frequency (Hz) 90 80 70 14 RL to VS /2 13 25C 12 125C 11 -55C 10 -10 -11 -55C -12 125C -13 -14 25C -15 60 10 1 100 0 Load (k) 4 6 8 Output Current (mA) (R) OPA244, 2244, 4244 2 6 10 12 14 TYPICAL PERFORMANCE CURVES (Cont.) At TA = 25C, VS = +15V, and RL = 20k connected to Ground, unless otherwise noted. INPUT BIAS CURRENT vs INPUT COMMON-MODE VOLTAGE INPUT BIAS CURRENT vs TEMPERATURE -12 -12 -11 Bias Current (nA) Bias Current (nA) -10 -8 -6 -10 -IB -9 +IB -8 -7 -4 -6 -2 -15 -10 -5 0 5 10 -5 -75 15 -50 -25 0 Common-Mode Voltage (V) AOL, CMRR, PSRR vs TEMPERATURE 0.20 120 0.18 Slew Rate (V/s) 110 CMRR 100 95 AOL 90 100 125 0.14 0.12 -SR 0.10 0.08 VS = 7.5, RL = 20k, CL = 100pF, Gain = +1 0.06 0.04 85 0.02 0.00 -75 -50 0 -25 25 75 50 100 -75 125 -25 75 25 175 125 Temperature(C) Temperature (C) COMMON-MODE REJECTION vs SUPPY VOLTAGE QUIESCENT CURRENT AND SHORT-CIRCUIT vs SUPPLY VOLTAGE 52 100 48 Quiescent Current (A) 120 80 60 40 20 0 35 IQ 30 44 25 -ISC 40 20 36 15 +ISC 32 10 28 5 24 0 4 8 12 16 20 24 28 32 36 0 0 Suppy Voltage (V) Short-Circuit Current (mA) 80 CMRR (dB) 75 +SR 0.16 PSRR 105 50 SLEW RATE vs TEMPERATURE 125 115 25 Temperature (C) 4 8 12 16 20 24 28 32 36 Supply Voltage (V) (R) 7 OPA244, 2244, 4244 TYPICAL PERFORMANCE CURVES (Cont.) At TA = 25C, VS = +15V, and RL = 20k connected to Ground, unless otherwise noted. 50 -ISC 45 40 10 +ISC 35 25 -75 -50 -25 0 25 50 75 100 0 125 -75 -50 0 -25 100 Voltage Noise 10 Output Voltage (Vp-p) Current Noise Current Noise (fAHz) Voltage Noise (nVHz) 50 75 100 0 125 MAXIMUM OUTPUT VOLTAGE vs FREQUENCY 100 VS = 36V 30 25 20 VS =15V 15 10 5 1 1k 10k 1 100k VS = 2.7V 0 100 1k 10k 100k 1M Frequency(Hz) Frequency (Hz) SMALL SIGNAL OVERSHOOT vs LOAD CAPACITANCE 70% 60 OPA244 OPA4244 60% G = +1 G = -2 OPA2244 50% 40 Overshoot (%) Overshoot (%) 25 40 35 50 +10 20 1000 100 +15 +ISC Temperature (C) 1000 10 -15 IQ +5 INPUT VOLTAGE AND CURRENT NOISE SPECTRAL DENSITY vs FREQUENCY 1 -20 30 Temperature (C) 10 -25 -ISC 35 5 30 -30 OPA4244 G = -1 30 G = +3 20 40% G = +1, RL = 30% 20% G = +1, RL = 20k G = +2, RL = 20k 10 10% G = +3, RL = 20k 0% 0 100 1k 10 10k (R) OPA244, 2244, 4244 100 1k Load Capacitance (pF) Load Capacitance (pF) 8 10k Short-Circuit Current (mA) 55 Quiescent Current (A) Quiescent Current (A) 60 Short-Circuit Current (mA) QUIESCENT AND SHORT-CIRCUIT CURRENT vs TEMPERATURE 40 60 OPA244 35 55 OPA2244 30 50 25 45 20 IQ 40 15 65 TYPICAL PERFORMANCE CURVES (Cont.) At TA = 25C, VS = +15V, and RL = 20k connected to Ground, unless otherwise noted. LARGE-SIGNAL STEP RESPONSE, G = 1, CL = 100pF OPA244 OPA4244 2V/div 2V/div OPA2244 50s/div 25s/div SMALL-SIGNAL STEP RESPONSE, G = 1, CL = 100pF OPA244 OPA4244 50mV/div 50mV/div OPA2244 10s/div 10s/div OFFSET VOLTAGE PRODUCTION DISTRIBUTION 30 12 OPA4244 OPA244 25 1800 1500 1200 900 600 300 0 -1500 1500 1300 900 1100 700 500 300 -100 0 100 -300 -500 -700 0 -900 0 -1100 5 -1300 2 -300 10 -600 4 15 -900 6 20 -1200 Percent of Amplifiers (%) OPA2244 8 -1500 Percent of Amplifiers (%) 10 Offset Voltage (V) Offset Voltage (V) (R) 9 OPA244, 2244, 4244 TYPICAL PERFORMANCE CURVES (Cont.) At TA = 25C, VS = +15V, and RL = 20k connected to Ground, unless otherwise noted. OFFSET VOLTAGE PRODUCTION DISTRIBUTION 70 OPA244 60 OPA2244 50 35 Percent of Amplifiers (%) Percent of Amplifiers (%) 30 25 20 15 10 40 30 20 5 10 0 0 0 1 2 3 4 5 6 7 8 9 10 0 VOS Drift (V/C) 0.5 1 1.5 2 2.5 3 3.5 VOS Drift (V/C) (R) OPA244, 2244, 4244 OPA4244 10 4 4.5 5.0 5.5 APPLICATIONS INFORMATION This allows a designer to have the same assured performance at any supply voltage within this range. In addition, many key parameters are guaranteed over the specified temperature range, -40C to +85C. Most behavior remains unchanged throughout the full operating voltage range. Parameters which vary significantly with operating voltage or temperature are shown in typical performance curves. The OPA244 is unity-gain stable and suitable for a wide range of general purpose applications. Power supply pins should be bypassed with 0.01F ceramic capacitors. OPERATING VOLTAGE The OPA244 can operate from single supply (+2.2V to +36V) or dual supplies (1.1 to 18V) with excellent performance. Unlike most op amps which are specified at only one supply voltage, the OPA244 is specified for real world applications; a single set of specifications applies throughout the +2.6V to +36V (1.3 to 18V) supply range. Useful information on solder pad design for printed circuit boards can be found in Burr-Brown's Application Bulletin AB-132B, "Solder Pad Recommendations for SurfaceMount Devices," easily found at Burr-Brown's web site (http://www.burr-brown.com). RH 10 To Load IH R1 38.3k R5 383k High-Side Current Sense R3 38.3k V+ -In A1 +In OPA244 V+ for A1, A2 R4 20k + 2.2V to 36V (1.1V to 18V) R8 100k Out VO = 10 * IH * RH V- R2 19.1k R2 and R4 divide down the common-mode input to A1. V- for A1, A2 V+ -In A2 +In OPA244 V- R7 9.09k R6 10k RL 10 Out VO = 10 * IL * RL Low-Side Current Sense Common-mode range of A2 extends to V- for low-side sensing. Optional for IB Cancellation (R7 = R6 II R8) To Load IL NOTE: Low and high-side sensing circuits can be used independently. FIGURE 1. Low and High-Side Battery Current Sensing. (R) 11 OPA244, 2244, 4244 PACKAGE OPTION ADDENDUM www.ti.com 16-Aug-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) OPA2244EA/250 ACTIVE VSSOP DGK 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA2244EA/250G4 ACTIVE VSSOP DGK 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA2244EA/2K5 ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA2244EA/2K5G4 ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA2244PA ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type OPA2244PAG4 ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type OPA2244UA ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR OPA2244UA/2K5 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR OPA2244UA/2K5G4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR OPA2244UAG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR OPA244NA/250 ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA244NA/250G4 ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA244NA/3K ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA244NA/3KG4 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA244PA ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type OPA244PAG4 ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type OPA244UA ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Addendum-Page 1 Samples (Requires Login) PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 16-Aug-2012 Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) OPA244UA/2K5 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR OPA244UA/2K5E4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR OPA244UAE4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR OPA4244EA/250 ACTIVE TSSOP PW 14 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR OPA4244EA/250E4 ACTIVE TSSOP PW 14 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR OPA4244EA/2K5 ACTIVE TSSOP PW 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR OPA4244EA/2K5E4 ACTIVE TSSOP PW 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Samples (Requires Login) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. Addendum-Page 2 PACKAGE OPTION ADDENDUM www.ti.com 16-Aug-2012 In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 16-Aug-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant OPA2244EA/250 VSSOP DGK 8 250 180.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 OPA2244EA/2K5 VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 OPA2244UA/2K5 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 OPA244UA/2K5 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 OPA4244EA/250 TSSOP PW 14 250 180.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 OPA4244EA/2K5 TSSOP PW 14 2500 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 16-Aug-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) OPA2244EA/250 VSSOP DGK 8 250 210.0 185.0 35.0 OPA2244EA/2K5 VSSOP DGK 8 2500 367.0 367.0 35.0 OPA2244UA/2K5 SOIC D 8 2500 367.0 367.0 35.0 OPA244UA/2K5 SOIC D 8 2500 367.0 367.0 35.0 OPA4244EA/250 TSSOP PW 14 250 210.0 185.0 35.0 OPA4244EA/2K5 TSSOP PW 14 2500 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated