M 24LC16B 16K 2.5V I2CTM Serial EEPROM FEATURES DESCRIPTION * Single supply with operation down to 2.5V * Low power CMOS technology - 1 mA active current typical - 10 A standby current typical at 5.5V - 5 A standby current typical at 3.0V * Organized as 8 blocks of 256 bytes (8 x 256 x 8) * 2-wire serial interface bus, I2CTM compatible * Schmitt trigger inputs for noise suppression * Output slope control to eliminate ground bounce * 100 kHz (E-temp.) and 400 kHz (C/I-temp.) compatibility * Self-timed write cycle (including auto-erase) * Page-write buffer for up to 16 bytes * 2 ms typical write cycle time for page-write * Hardware write protect for entire memory * Can be operated as a serial ROM * Factory programming (QTP) available * ESD protection > 4,000V * 1,000,000 erase/write cycles * Data retention > 200 years * 8-pin PDIP, SOIC, TSSOP and MSOP packages * Available for extended temperature ranges: - Industrial (I): -40C to +85C - Automotive (E): -40C to +125C The Microchip Technology Inc. 24LC16B is a 16 Kbit Electrically Erasable PROM. The device is organized as eight blocks of 256 x 8-bit memory with a 2-wire serial interface. Low voltage design permits operation down to 2.5V with standby and active currents of only 5 A and 1 mA respectively. The 24LC16B also has a page-write capability for up to 16 bytes of data. The 24LC16B is available in the standard 8-pin DIP, surface mount SOIC, TSSOP and MSOP packages. BLOCK DIAGRAM WP I/O CONTROL LOGIC HV GENERATOR MEMORY CONTROL LOGIC EEPROM ARRAY XDEC PAGE LATCHES I/O SCL YDEC SDA VCC SENSE AMP R/W CONTROL VSS PACKAGE TYPES SOIC PDIP 3 VSS 4 VCC 7 WP 6 SCL 5 SDA A0 1 A1 2 A2 3 VSS 4 8 7 6 5 VCC WP SCL SDA A0 1 A1 2 A2 3 VSS 4 MSOP 8 7 6 5 VCC WP SCL SDA A0 1 A1 2 A2 3 VSS 4 24LC16B A2 8 24LC16B 2 24LC16B 1 A1 24LC16B A0 TSSOP 8 VCC 7 WP 6 SCL 5 SDA Note: Pins A0, A1 and A2 are not used by the 24LC16B. (No internal connections). I2CTM is a trademark of the Philips Corporation 2001 Microchip Technology Inc. DS20070M-page 1 24LC16B 1.0 ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings VCC .............................................................................................................................................................................7.0V All inputs and outputs w.r.t. VSS ......................................................................................................... -0.3V to VCC +1.0V Storage temperature ...............................................................................................................................-65C to +150C Ambient temp. with power applied ..........................................................................................................-65C to +125C Soldering temperature of leads (10 seconds) .......................................................................................................+300C ESD protection on all pins ..................................................................................................................................................... 4 KV NOTICE: Stresses above those listed under "Maximum ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. 1.1 DC Characteristics DC CHARACTERISTICS Param. No. Sym. D1 VIH D2 D3 D4 VHYS D5 VOL Characteristic VCC = +2.5V to +5.5V Industrial (I): TAMB = -40C to +85C Automotive (E): TAMB = -40C to +125C Min. Max. Units WP, SCL and SDA pins -- -- -- -- -- High level input voltage .7 VCC -- V -- VIL Low level input voltage -- .3 VCC V -- .05 VCC -- V (Note) Low level output voltage -- .40 V IOL = 3.0 mA, VCC = 2.5V Hysteresis of Schmitt trigger inputs Conditions D6 ILI Input leakage current -10 10 A VIN = .1V to VCC D7 ILO Output leakage current -10 10 A VOUT = .1V to VCC D8 CIN, COUT Pin capacitance (all inputs/outputs) -- 10 pF VCC = 5.0V (Note) TAMB = 25C, FCLK = 1 MHz D9 ICC write Operating current -- 3 mA VCC = 5.5V, SCL = 400 kHz D10 ICC read -- 1 mA -- D11 ICCS -- -- 30 100 VCC = 3.0V, SDA = SCL = VCC VCC = 5.5V, SDA = SCL = VCC WP = VSS Note: Standby current This parameter is periodically sampled and not 100% tested. DS20070M-page 2 2001 Microchip Technology Inc. 24LC16B 1.2 AC Characteristics AC CHARACTERISTICS Param. No. Sym. 1 FCLK 2 Characteristic. VCC = +2.5V to +5.5V Industrial (I): TAMB = -40C to +85C Automotive (E): TAMB = -40C to +125C Min. Max. Units Conditions Clock frequency -- -- 400 100 kHz 2.5V VCC 5.5V 2.5V VCC 5.5V (E-temp. range) THIGH Clock high time 600 4000 -- -- ns 2.5V VCC 5.5V 2.5V VCC 5.5V (E-temp. range) 3 TLOW Clock low time 1300 4700 -- -- ns 2.5V VCC 5.5V 2.5V VCC 5.5V (E-temp. range) 4 TR SDA and SCL rise time (Note 1) -- -- 300 1000 ns 2.5V VCC 5.5V (Note 1) 2.5V VCC 5.5V (E-temp. range) (Note 1) TF SDA and SCL fall time -- 300 ns (Note 1) 6 THD:STA START condition hold time 600 4000 -- -- ns 2.5V VCC 5.5V 2.5V VCC 5.5V (E-temp. range) 7 TSU:STA 600 4700 -- -- ns 2.5V VCC 5.5V 2.5V VCC 5.5V (E-temp. range) 8 THD:DAT Data input hold time 0 -- ns (Note 2) 9 TSU:DAT Data input setup time 100 250 -- -- ns 2.5V VCC 5.5V 2.5V VCC 5.5V (E-temp. range) 10 TSU:STO STOP condition setup time 600 4000 -- -- ns 2.5V VCC 5.5V 2.5V VCC 5.5V (E-temp. range) -- -- 900 3500 ns 2.5V VCC 5.5V 2.5V VCC 5.5V (E-temp. range) 1300 4700 -- -- ns 2.5V VCC 5.5V 2.5V VCC 5.5V (E-temp. range) 5 START condition setup time Output valid from clock (Note 2) 11 TAA 12 TBUF 13 TOF 20+0.1CB Output fall time from VIH -- minimum to VIL maximum 250 250 ns 2.5V VCC 5.5V 2.5V VCC 5.5V (E-temp. range) 14 TSP Input filter spike suppression (SDA and SCL pins) -- 50 ns (Notes 1 and 3) 15 TWC Write cycle time (byte or page) -- 5 ms -- 16 -- Endurance 1M -- Bus free time: Time the bus must be free before a new transmission can start cycles 25C, VCC = 5.0V, Block Mode (Note 4) Note 1: Not 100% tested. CB = total capacitance of one bus line in pF. 2: As a transmitter, the device must provide an internal minimum delay time to bridge the undefined region (minimum 300 ns) of the falling edge of SCL to avoid unintended generation of START or STOP conditions. 3: The combined TSP and VHYS specifications are due to new Schmitt trigger inputs which provide improved noise spike suppression. This eliminates the need for a TI specification for standard operation. 4: This parameter is not tested but ensured by characterization. For endurance estimates in a specific application, please consult the Total Endurance Model which can be obtained on Microchip's website: www.microchip.com. 2001 Microchip Technology Inc. DS20070M-page 3 24LC16B FIGURE 1-1: BUS TIMING DATA 5 4 2 3 SCL 7 SDA IN 8 10 9 6 14 12 11 SDA OUT FIGURE 1-2: BUS TIMING START/STOP D4 SCL 6 7 10 SDA START DS20070M-page 4 STOP 2001 Microchip Technology Inc. 24LC16B 2.0 FUNCTIONAL DESCRIPTION The 24LC16B supports a bi-directional 2-wire bus and data transmission protocol. A device that sends data onto the bus is defined as transmitter, and a device receiving data as receiver. The bus has to be controlled by a master device which generates the serial clock (SCL), controls the bus access and generates the START and STOP conditions, while the 24LC16B works as slave. Both master and slave can operate as transmitter or receiver, but the master device determines which mode is activated. 3.0 BUS CHARACTERISTICS The following bus protocol has been defined: * Data transfer may be initiated only when the bus is not busy. * During data transfer, the data line must remain stable whenever the clock line is HIGH. Changes in the data line while the clock line is HIGH will be interpreted as a START or STOP condition. Accordingly, the following bus conditions have been defined (Figure 3-1). 3.1 Start Data Transfer (B) A HIGH to LOW transition of the SDA line while the clock (SCL) is HIGH determines a START condition. All commands must be preceded by a START condition. 3.3 Stop Data Transfer (C) A LOW to HIGH transition of the SDA line while the clock (SCL) is HIGH determines a STOP condition. All operations must be ended with a STOP condition. FIGURE 3-1: (A) Data Valid (D) The state of the data line represents valid data when, after a START condition, the data line is stable for the duration of the HIGH period of the clock signal. The data on the line must be changed during the LOW period of the clock signal. There is one clock pulse per bit of data. Each data transfer is initiated with a START condition and terminated with a STOP condition. The number of the data bytes transferred between the START and STOP conditions is determined by the master device and is theoretically unlimited, although only the last sixteen will be stored when doing a write operation. When an overwrite does occur it will replace data in a first-in first-out (FIFO) fashion. 3.5 Acknowledge Each receiving device, when addressed, is obliged to generate an acknowledge after the reception of each byte. The master device must generate an extra clock pulse which is associated with this acknowledge bit. Note: Bus not Busy (A) Both data and clock lines remain HIGH. 3.2 3.4 The 24LC16B does not generate any acknowledge bits if an internal programming cycle is in progress. The device that acknowledges, has to pull down the SDA line during the acknowledge clock pulse in such a way that the SDA line is stable LOW during the HIGH period of the acknowledge related clock pulse. Of course, setup and hold times must be taken into account. During reads, a master must signal an end of data to the slave by not generating an acknowledge bit on the last byte that has been clocked out of the slave. In this case, the slave (24LC16B) will leave the data line HIGH to enable the master to generate the STOP condition. DATA TRANSFER SEQUENCE ON THE SERIAL BUS (B) (D) (D) (C) (A) SCL SDA START CONDITION 2001 Microchip Technology Inc. ADDRESS OR DATA ACKNOWLEDGE ALLOWED VALID TO CHANGE STOP CONDITION DS20070M-page 5 24LC16B 3.6 FIGURE 3-2: Device Addressing A control byte is the first byte received following the start condition from the master device. The control byte consists of a four bit control code, for the 24LC16B this is set as 1010 binary for read and write operations. The next three bits of the control byte are the block select bits (B2, B1, B0). They are used by the master device to select which of the eight 256 word blocks of memory are to be accessed. These bits are in effect the three most significant bits of the word address. It should be noted that the protocol limits the size of the memory to eight blocks of 256 words, therefore the protocol can support only one 24LC16B per system. CONTROL BYTE ALLOCATION START READ/WRITE R/W SLAVE ADDRESS 1 0 1 0 B2 B1 A B0 X = Don't care The last bit of the control byte defines the operation to be performed. When set to `1' a read operation is selected, when set to `0' a write operation is selected. Following the START condition, the 24LC16B monitors the SDA bus checking the device type identifier being transmitted, upon a 1010 code the slave device outputs an acknowledge signal on the SDA line. Depending on the state of the R/W bit, the 24LC16B will select a read or write operation. Operation Control Code Block Select R/W Read 1010 Block Address 1 Write 1010 Block Address 0 DS20070M-page 6 2001 Microchip Technology Inc. 24LC16B 4.0 WRITE OPERATION 4.1 Byte Write after the master has transmitted a STOP condition. After the receipt of each word, the four lower order address pointer bits are internally incremented by `1'. The higher order 7 bits of the word address remains constant. If the master should transmit more than 16 words prior to generating the STOP condition, the address counter will roll over and the previously received data will be overwritten. As with the byte write operation, once the STOP condition is received an internal write cycle will begin (Figure 4-2). Following the START condition from the master, the device code (4 bits), the block address (3 bits) and the R/W bit which is a logic LOW is placed onto the bus by the master transmitter. This indicates to the addressed slave receiver that a byte with a word address will follow after it has generated an acknowledge bit during the ninth clock cycle. Therefore, the next byte transmitted by the master is the word address and will be written into the address pointer of the 24LC16B. After receiving another acknowledge signal from the 24LC16B, the master device will transmit the data word to be written into the addressed memory location. The 24LC16B acknowledges again and the master generates a STOP condition. This initiates the internal write cycle, and during this time the 24LC16B will not generate acknowledge signals (Figure 4-1). 4.2 Note: Page write operations are limited to writing bytes within a single physical page, regardless of the number of bytes actually being written. Physical page boundaries start at addresses that are integer multiples of the page buffer size (or `page size') and end at addresses that are integer multiples of [page size - 1]. If a page write command attempts to write across a physical page boundary, the result is that the data wraps around to the beginning of the current page (overwriting data previously stored there), instead of being written to the next page as might be expected. It is therefore necessary for the application software to prevent page write operations that would attempt to cross a page boundary. Page Write The write control byte, word address and the first data byte are transmitted to the 24LC16B in the same way as in a byte write. But instead of generating a STOP condition the master transmits up to 16 data bytes to the 24LC16B, which are temporarily stored in the onchip page buffer and will be written into the memory FIGURE 4-1: BYTE WRITE BUS ACTIVITY MASTER S T A R T SDA LINE S CONTROL BYTE WORD ADDRESS DATA P A C K BUS ACTIVITY FIGURE 4-2: S T O P A C K A C K PAGE WRITE BUS ACTIVITY MASTER S T A R T SDA LINE S CONTROL BYTE BUS ACTIVITY 2001 Microchip Technology Inc. WORD ADDRESS (n) DATA (n) S T O P DATA (n + 15) DATA (n + 1) P A C K A C K A C K A C K A C K DS20070M-page 7 24LC16B 5.0 ACKNOWLEDGE POLLING Since the device will not acknowledge during a write cycle, this can be used to determine when the cycle is complete (this feature can be used to maximize bus throughput). Once the STOP condition for a write command has been issued from the master, the device initiates the internally timed write cycle. ACK polling can be initiated immediately. This involves the master sending a start condition followed by the control byte for a write command (R/W = 0). If the device is still busy with the write cycle, then no ACK will be returned. If the cycle is complete, then the device will return the ACK and the master can then proceed with the next read or write command. See Figure 5-1 for flow diagram. FIGURE 5-1: 6.0 WRITE PROTECTION The 24LC16B can be used as a serial ROM when the WP pin is connected to VCC. Programming will be inhibited and the entire memory will be write-protected. ACKNOWLEDGE POLLING FLOW Send Write Command Send Stop Condition to Initiate Write Cycle Send Start Send Control Byte with R/W = 0 Did Device Acknowledge (ACK = 0)? No Yes Next Operation DS20070M-page 8 2001 Microchip Technology Inc. 24LC16B 7.0 READ OPERATION 7.3 Read operations are initiated in the same way as write operations with the exception that the R/W bit of the slave address is set to `1'. There are three basic types of read operations: current address read, random read and sequential read. 7.1 Current Address Read The 24LC16B contains an address counter that maintains the address of the last word accessed, internally incremented by `1'. Therefore, if the previous access (either a read or write operation) was to address n, the next current address read operation would access data from address n + 1. Upon receipt of the slave address with R/W bit set to `1', the 24LC16B issues an acknowledge and transmits the 8-bit data word. The master will not acknowledge the transfer but does generate a STOP condition and the 24LC16B discontinues transmission (Figure 7-1). 7.2 Random Read Sequential Read Sequential reads are initiated in the same way as a random read except that after the 24LC16B transmits the first data byte, the master issues an acknowledge as opposed to a STOP condition in a random read. This directs the 24LC16B to transmit the next sequentially addressed 8-bit word (Figure 7-3). To provide sequential reads the 24LC16B contains an internal address pointer which is incremented by one at the completion of each operation. This address pointer allows the entire memory contents to be serially read during one operation. 7.4 Noise Protection The 24LC16B employs a VCC threshold detector circuit which disables the internal erase/write logic if the VCC is below 1.5V at nominal conditions. The SCL and SDA inputs have Schmitt trigger and filter circuits which suppress noise spikes to assure proper device operation even on a noisy bus. Random read operations allow the master to access any memory location in a random manner. To perform this type of read operation, first the word address must be set. This is done by sending the word address to the 24LC16B as part of a write operation. After the word address is sent, the master generates a START condition following the acknowledge. This terminates the write operation, but not before the internal address pointer is set. Then the master issues the control byte again but with the R/W bit set to a `1'. The 24LC16B will then issue an acknowledge and transmits the 8-bit data word. The master will not acknowledge the transfer but does generate a STOP condition and the 24LC16B discontinues transmission (Figure 7-2). FIGURE 7-1: CURRENT ADDRESS READ BUS ACTIVITY MASTER S T A R T SDA LINE S BUS ACTIVITY CONTROL BYTE S T O P DATA (n) P A C K N O A C K 2001 Microchip Technology Inc. DS20070M-page 9 24LC16B FIGURE 7-2: RANDOM READ S BUS ACTIVITY T A MASTER R T CONTROL BYTE S T A R T WORD ADDRESS (n) S S T O P DATA (n) P S SDA LINE A C K A C K BUS ACTIVITY FIGURE 7-3: CONTROL BYTE A C K N O A C K SEQUENTIAL READ BUS ACTIVITY MASTER CONTROL BYTE DATA (n) DATA (n + 1) DATA (n + 2) S T O P DATA (n + X) SDA LINE BUS ACTIVITY P A C K A C K A C K A C K N O A C K DS20070M-page 10 2001 Microchip Technology Inc. 24LC16B 8.0 PIN DESCRIPTIONS The descriptions of the pins are listed in Table 8-1. TABLE 8-1: PIN FUNCTION TABLE Name PDIP SOIC TSSOP MSOP Description A0 1 1 1 1 Not Connected A1 2 2 2 2 Not Connected A2 3 3 3 3 Not Connected VSS 4 4 4 4 Ground SDA 5 5 5 5 Serial Address/Data I/O SCL 6 6 6 6 Serial Clock WP 7 7 7 7 Write Protect Input VCC 8 8 8 8 +2.5V to 5.5V Power Supply 8.1 Serial Address/Data Input/Output (SDA) This is a bi-directional pin used to transfer addresses and data into and data out of the device. It is an open drain terminal. Therefore, the SDA bus requires a pullup resistor to VCC (typical 10 k for 100 kHz, 2 k for 400 kHz). For normal data transfer SDA is allowed to change only during SCL LOW. Changes during SCL HIGH are reserved for indicating the START and STOP conditions. 8.2 Serial Clock (SCL) This input is used to synchronize the data transfer from and to the device. 8.3 Write-Protect (WP) This pin must be connected to either VSS or VCC. If tied to VSS normal memory operation is enabled (read/write the entire memory 000-7FF). If tied to VCC, WRITE operations are inhibited. The entire memory will be write-protected. Read operations are not affected. This feature allows the user to use the 24LC16B as a serial ROM when WP is enabled (tied to VCC). 8.4 A0, A1, A2 These pins are not used by the 24LC16B. They may be left floating or tied to either VSS or VCC. 2001 Microchip Technology Inc. DS20070M-page 11 24LC16B 9.0 PACKAGING INFORMATION 9.1 Package Marking Information 8-Lead PDIP (300 mil) XXXXXXXX XXXXXNNN YYWW 24LC16B /PNNN YYWW 8-Lead SOIC (150 mil) XXXXXXXX XXXXYYWW NNN Example: Example: 24LC16B SNYYWW NNN 8-Lead TSSOP Example: XXXX 4L16 XYWW YWW NNN NNN 8-Lead MSOP Example: XXXXXX YWWNNN Legend: Note: * XX...X Y YY WW NNN 4L16I YWWNNN Customer specific information* Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week `01') Alphanumeric traceability code In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line thus limiting the number of available characters for customer specific information. Standard PICmicro device marking consists of Microchip part number, year code, week code, and traceability code. For PICmicro device marking beyond this, certain price adders apply. Please check with your Microchip Sales Office. For QTP devices, any special marking adders are included in QTP price. DS20070M-page 12 2001 Microchip Technology Inc. 24LC16B 8-Lead Plastic Dual In-line (P) - 300 mil (PDIP) E1 D 2 n 1 E A2 A L c A1 B1 p eB B Units Dimension Limits n p Number of Pins Pitch Top to Seating Plane Molded Package Thickness Base to Seating Plane Shoulder to Shoulder Width Molded Package Width Overall Length Tip to Seating Plane Lead Thickness Upper Lead Width Lower Lead Width Overall Row Spacing Mold Draft Angle Top Mold Draft Angle Bottom * Controlling Parameter Significant Characteristic A A2 A1 E E1 D L c B1 B eB MIN .140 .115 .015 .300 .240 .360 .125 .008 .045 .014 .310 5 5 INCHES* NOM MAX 8 .100 .155 .130 .170 .145 .313 .250 .373 .130 .012 .058 .018 .370 10 10 .325 .260 .385 .135 .015 .070 .022 .430 15 15 MILLIMETERS NOM 8 2.54 3.56 3.94 2.92 3.30 0.38 7.62 7.94 6.10 6.35 9.14 9.46 3.18 3.30 0.20 0.29 1.14 1.46 0.36 0.46 7.87 9.40 5 10 5 10 MIN MAX 4.32 3.68 8.26 6.60 9.78 3.43 0.38 1.78 0.56 10.92 15 15 Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" (0.254mm) per side. JEDEC Equivalent: MS-001 Drawing No. C04-018 2001 Microchip Technology Inc. DS20070M-page 13 24LC16B 8-Lead Plastic Small Outline (SN) - Narrow, 150 mil (SOIC) E E1 p D 2 B n 1 h 45x c A2 A f L Units Dimension Limits n p Number of Pins Pitch Overall Height Molded Package Thickness Standoff Overall Width Molded Package Width Overall Length Chamfer Distance Foot Length Foot Angle Lead Thickness Lead Width Mold Draft Angle Top Mold Draft Angle Bottom * Controlling Parameter Significant Characteristic A A2 A1 E E1 D h L f c B MIN .053 .052 .004 .228 .146 .189 .010 .019 0 .008 .013 0 0 A1 INCHES* NOM 8 .050 .061 .056 .007 .237 .154 .193 .015 .025 4 .009 .017 12 12 MAX .069 .061 .010 .244 .157 .197 .020 .030 8 .010 .020 15 15 MILLIMETERS NOM 8 1.27 1.35 1.55 1.32 1.42 0.10 0.18 5.79 6.02 3.71 3.91 4.80 4.90 0.25 0.38 0.48 0.62 0 4 0.20 0.23 0.33 0.42 0 12 0 12 MIN MAX 1.75 1.55 0.25 6.20 3.99 5.00 0.51 0.76 8 0.25 0.51 15 15 Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" (0.254mm) per side. JEDEC Equivalent: MS-012 Drawing No. C04-057 DS20070M-page 14 2001 Microchip Technology Inc. 24LC16B 8-Lead Plastic Thin Shrink Small Outline (ST) - 4.4 mm (TSSOP) E E1 p D 2 1 n B A c A1 f A2 L Units Dimension Limits n p Number of Pins Pitch Overall Height Molded Package Thickness Standoff Overall Width Molded Package Width Molded Package Length Foot Length Foot Angle Lead Thickness Lead Width Mold Draft Angle Top Mold Draft Angle Bottom * Controlling Parameter Significant Characteristic A A2 A1 E E1 D L f c B MIN INCHES NOM MAX 8 .026 .033 .002 .246 .169 .114 .020 0 .004 .007 0 0 .035 .004 .251 .173 .118 .024 4 .006 .010 5 5 .043 .037 .006 .256 .177 .122 .028 8 .008 .012 10 10 MILLIMETERS* NOM MAX 8 0.65 1.10 0.85 0.90 0.95 0.05 0.10 0.15 6.25 6.38 6.50 4.30 4.40 4.50 2.90 3.00 3.10 0.50 0.60 0.70 0 4 8 0.09 0.15 0.20 0.19 0.25 0.30 0 5 10 0 5 10 MIN Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .005" (0.127mm) per side. JEDEC Equivalent: MO-153 Drawing No. C04-086 2001 Microchip Technology Inc. DS20070M-page 15 24LC16B 8-Lead Plastic Micro Small Outline Package (MSOP) 2 n 1 MILLIMETERS* INCHES Units MAX MIN NOM NOM MAX Dimension Limits MIN n 8 8 Number of Pins p 0.65 TYP. .026 TYP. Pitch .043 1.10 Overall Height A .036 0.81 0.86 0.91 Molded Package Thickness A2 .032 .034 .006 0.05 0.15 Standoff A1 .002 4.90 TYP. Overall Width E .193 TYP. .120 2.95 3.00 3.05 Molded Package Width E1 .116 .118 .120 2.95 3.00 3.05 Overall Length D .116 .118 .028 0.40 0.55 0.70 Foot Length L .016 .022 Footprint (Reference) F .035 .037 .039 0.90 0.95 1.00 Foot Angle 0 6 0 6 c Lead Thickness .005 .006 .007 0.13 0.15 0.18 Lead Width B .010 .012 .016 0.25 0.30 0.40 Mold Draft Angle Top 7 7 Mold Draft Angle Bottom 7 7 *Controlling Parameter Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" (0.254mm) per side. DS20070M-page 16 2001 Microchip Technology Inc. 24LC16B ON-LINE SUPPORT Microchip provides on-line support on the Microchip World Wide Web (WWW) site. The web site is used by Microchip as a means to make files and information easily available to customers. To view the site, the user must have access to the Internet and a web browser, such as Netscape(R) or Microsoft(R) Explorer. Files are also available for FTP download from our FTP site. Systems Information and Upgrade Hot Line The Systems Information and Upgrade Line provides system users a listing of the latest versions of all of Microchip's development systems software products. Plus, this line provides information on how customers can receive any currently available upgrade kits.The Hot Line Numbers are: 1-800-755-2345 for U.S. and most of Canada, and 1-480-792-7302 for the rest of the world. Connecting to the Microchip Internet Web Site The Microchip web site is available by using your favorite Internet browser to attach to: www.microchip.com The file transfer site is available by using an FTP service to connect to: ftp://ftp.microchip.com The web site and file transfer site provide a variety of services. Users may download files for the latest Development Tools, Data Sheets, Application Notes, User's Guides, Articles and Sample Programs. A variety of Microchip specific business information is also available, including listings of Microchip sales offices, distributors and factory representatives. Other data available for consideration is: * Latest Microchip Press Releases * Technical Support Section with Frequently Asked Questions * Design Tips * Device Errata * Job Postings * Microchip Consultant Program Member Listing * Links to other useful web sites related to Microchip Products * Conferences for products, Development Systems, technical information and more * Listing of seminars and events 2001 Microchip Technology Inc. DS20070M-page 17 24LC16B READER RESPONSE It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip product. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our documentation can better serve you, please FAX your comments to the Technical Publications Manager at (480) 792-7578. Please list the following information, and use this outline to provide us with your comments about this Data Sheet. To: Technical Publications Manager RE: Reader Response Total Pages Sent From: Name Company Address City / State / ZIP / Country Telephone: (_______) _________ - _________ FAX: (______) _________ - _________ Application (optional): Would you like a reply? Y N Device: 24LC16B Literature Number: DS20070M Questions: 1. What are the best features of this document? 2. How does this document meet your hardware and software development needs? 3. Do you find the organization of this data sheet easy to follow? If not, why? 4. What additions to the data sheet do you think would enhance the structure and subject? 5. What deletions from the data sheet could be made without affecting the overall usefulness? 6. Is there any incorrect or misleading information (what and where)? 7. How would you improve this document? 8. How would you improve our software, systems, and silicon products? DS20070M-page 18 2001 Microchip Technology Inc. 24LC16B NOTES: 2001 Microchip Technology Inc. DS20070M-page 19 24LC16B NOTES: DS20070M-page 20 2001 Microchip Technology Inc. 24LC16B NOTES: 2001 Microchip Technology Inc. DS20070M-page 21 24LC16B PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PART NO. Device Device: X /XX Temperature Package Range 24LC16B: = 16 Kbit I2C Serial EEPROM 24LC16BT: = 16 Kbit I2C Serial EEPROM (Tape and Reel) Temperature I Range: E = -40C to +85C = -40C to +125C Package: = = = = P SN ST MS Plastic DIP (300 mil body), 8-lead Plastic SOIC (150 mil body), 8-lead Plastic TSSOP (4.4 mm), 8-lead Plastic Micro Small Outline (MSOP), 8-lead Examples: a) 24LC16B-E/P: Extended Temp., PDIP package b) 24LC16B-E/SN: Extended Temp., SOIC package c) 24LC16BT-E/SN: Tape and Reel, Extended Temp., SOIC package d) 24LC16B-I/P: Industrial Temp., PDIP package e) 24LC16B-I/SN: Industrial Temp., SOIC package f) 24LC16BT-I/SN: Tape and Reel, Industrial Temp., SOIC package g) 24LC16B-I/ST: Industrial Temp., TSSOP package h) 24LC16BT-I/ST: Tape and Reel, Industrial Temp., TSSOP package Sales and Support Data Sheets Products supported by a preliminary Data Sheet may have an errata sheet describing minor operational differences and recommended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following: 1. 2. 3. Your local Microchip sales office The Microchip Corporate Literature Center U.S. Fax: (480) 792-7277 The Microchip Worldwide Site (www.microchip.com) Please specify which device, revision of silicon and Data Sheet (include Literature #) you are using. New Customer Notification System Register on our web site (www.microchip.com/cn) to receive the most current information on our products. DS20070M-page 22 2001 Microchip Technology Inc. 24LC16B "All rights reserved. Copyright (c) 2001, Microchip Technology Incorporated, USA. Information contained in this publication regarding device applications and the like is intended through suggestion only and may be superseded by updates. No representation or warranty is given and no liability is assumed by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement of patents or other intellectual property rights arising from such use or otherwise. Use of Microchip's products as critical components in life support systems is not authorized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, under any intellectual property rights. The Microchip logo and name are registered trademarks of Microchip Technology Inc. in the U.S.A. and other countries. All rights reserved. All other trademarks mentioned herein are the property of their respective companies. No licenses are conveyed, implicitly or otherwise, under any intellectual property rights." Trademarks The Microchip name, logo, PIC, PICmicro, PICMASTER, PICSTART, PRO MATE, KEELOQ, SEEVAL, MPLAB and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. Total Endurance, ICSP, In-Circuit Serial Programming, FilterLab, MXDEV, microID, FlexROM, fuzzyLAB, MPASM, MPLINK, MPLIB, PICDEM, ICEPIC, Migratable Memory, FanSense, ECONOMONITOR, Select Mode and microPort are trademarks of Microchip Technology Incorporated in the U.S.A. Serialized Quick Term Programming (SQTP) is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. (c) 2001, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Microchip received QS-9000 quality system certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona in July 1999. The Company's quality system processes and procedures are QS-9000 compliant for its PICmicro(R) 8-bit MCUs, KEELOQ(R) code hopping devices, Serial EEPROMs and microperipheral products. In addition, Microchip's quality system for the design and manufacture of development systems is ISO 9001 certified. 2001 Microchip Technology Inc. DS20070M-page 23 M WORLDWIDE SALES AND SERVICE AMERICAS New York Corporate Office 150 Motor Parkway, Suite 202 Hauppauge, NY 11788 Tel: 631-273-5305 Fax: 631-273-5335 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: 480-792-7627 Web Address: http://www.microchip.com Rocky Mountain 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7966 Fax: 480-792-7456 Atlanta 500 Sugar Mill Road, Suite 200B Atlanta, GA 30350 Tel: 770-640-0034 Fax: 770-640-0307 Austin Analog Product Sales 8303 MoPac Expressway North Suite A-201 Austin, TX 78759 Tel: 512-345-2030 Fax: 512-345-6085 Boston 2 Lan Drive, Suite 120 Westford, MA 01886 Tel: 978-692-3848 Fax: 978-692-3821 Boston Analog Product Sales Unit A-8-1 Millbrook Tarry Condominium 97 Lowell Road Concord, MA 01742 Tel: 978-371-6400 Fax: 978-371-0050 Chicago 333 Pierce Road, Suite 180 Itasca, IL 60143 Tel: 630-285-0071 Fax: 630-285-0075 Dallas 4570 Westgrove Drive, Suite 160 Addison, TX 75001 Tel: 972-818-7423 Fax: 972-818-2924 Dayton Two Prestige Place, Suite 130 Miamisburg, OH 45342 Tel: 937-291-1654 Fax: 937-291-9175 Detroit Tri-Atria Office Building 32255 Northwestern Highway, Suite 190 Farmington Hills, MI 48334 Tel: 248-538-2250 Fax: 248-538-2260 Los Angeles 18201 Von Karman, Suite 1090 Irvine, CA 92612 Tel: 949-263-1888 Fax: 949-263-1338 Mountain View Analog Product Sales 1300 Terra Bella Avenue Mountain View, CA 94043-1836 Tel: 650-968-9241 Fax: 650-967-1590 ASIA/PACIFIC (continued) Korea Microchip Technology Korea 168-1, Youngbo Bldg. 3 Floor Samsung-Dong, Kangnam-Ku Seoul, Korea Tel: 82-2-554-7200 Fax: 82-2-558-5934 San Jose Microchip Technology Inc. 2107 North First Street, Suite 590 San Jose, CA 95131 Tel: 408-436-7950 Fax: 408-436-7955 Singapore Microchip Technology Singapore Pte Ltd. 200 Middle Road #07-02 Prime Centre Singapore, 188980 Tel: 65-334-8870 Fax: 65-334-8850 Toronto 6285 Northam Drive, Suite 108 Mississauga, Ontario L4V 1X5, Canada Tel: 905-673-0699 Fax: 905-673-6509 Taiwan Microchip Technology Taiwan 11F-3, No. 207 Tung Hua North Road Taipei, 105, Taiwan Tel: 886-2-2717-7175 Fax: 886-2-2545-0139 ASIA/PACIFIC Australia Microchip Technology Australia Pty Ltd Suite 22, 41 Rawson Street Epping 2121, NSW Australia Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 EUROPE China - Beijing Denmark Microchip Technology Beijing Office Unit 915 New China Hong Kong Manhattan Bldg. No. 6 Chaoyangmen Beidajie Beijing, 100027, No. China Tel: 86-10-85282100 Fax: 86-10-85282104 Microchip Technology Denmark ApS Regus Business Centre Lautrup hoj 1-3 Ballerup DK-2750 Denmark Tel: 45 4420 9895 Fax: 45 4420 9910 France China - Shanghai Microchip Technology Shanghai Office Room 701, Bldg. B Far East International Plaza No. 317 Xian Xia Road Shanghai, 200051 Tel: 86-21-6275-5700 Fax: 86-21-6275-5060 Hong Kong Microchip Asia Pacific RM 2101, Tower 2, Metroplaza 223 Hing Fong Road Kwai Fong, N.T., Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 India Microchip Technology Inc. India Liaison Office Divyasree Chambers 1 Floor, Wing A (A3/A4) No. 11, O'Shaugnessey Road Bangalore, 560 025, India Tel: 91-80-2290061 Fax: 91-80-2290062 Japan Microchip Technology Intl. Inc. Benex S-1 6F 3-18-20, Shinyokohama Kohoku-Ku, Yokohama-shi Kanagawa, 222-0033, Japan Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Arizona Microchip Technology SARL Parc d'Activite du Moulin de Massy 43 Rue du Saule Trapu Batiment A - ler Etage 91300 Massy, France Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Germany Arizona Microchip Technology GmbH Gustav-Heinemann Ring 125 D-81739 Munich, Germany Tel: 49-89-627-144 0 Fax: 49-89-627-144-44 Germany Analog Product Sales Lochhamer Strasse 13 D-82152 Martinsried, Germany Tel: 49-89-895650-0 Fax: 49-89-895650-22 Italy Arizona Microchip Technology SRL Centro Direzionale Colleoni Palazzo Taurus 1 V. Le Colleoni 1 20041 Agrate Brianza Milan, Italy Tel: 39-039-65791-1 Fax: 39-039-6899883 United Kingdom Arizona Microchip Technology Ltd. 505 Eskdale Road Winnersh Triangle Wokingham Berkshire, England RG41 5TU Tel: 44 118 921 5869 Fax: 44-118 921-5820 01/30/01 All rights reserved. (c) 2001 Microchip Technology Incorporated. Printed in the USA. 5/01 Printed on recycled paper. Information contained in this publication regarding device applications and the like is intended through suggestion only and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. No representation or warranty is given and no liability is assumed by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement of patents or other intellectual property rights arising from such use or otherwise. Use of Microchip's products as critical components in life support systems is not authorized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, except as maybe explicitly expressed herein, under any intellectual property rights. The Microchip logo and name are registered trademarks of Microchip Technology Inc. in the U.S.A. and other countries. All rights reserved. All other trademarks mentioned herein are the property of their respective companies. DS20070M-page 24 2001 Microchip Technology Inc.