NCP59150, NCV59150 Series 1.5 A, Very Low-Dropout (VLDO) Fast Transient Response Regulator Series http://onsemi.com MARKING DIAGRAMS TAB 1 5 D2PAK CASE 936A Features TAB 3 D2PAK3 CASE 936 y 59150-xx AWLYWWG 1 1 DFN8 CASE 488AF GND 1 VOUT Output Current in Excess of 1.5 A 300 mV Typical Dropout Voltage at 1.5 A Adjustable and Fixed Output Voltage Options Low Ground Current Fast Transient Response Stable with Ceramic Output Capacitor Logic Compatible Enable and Error Flag Pins Current Limit, Reverse Current and Thermal Shutdown Protection Operation up to 13.5 V Input Voltage NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC-Q100 Qualified and PPAP Capable These are Pb-Free Devices 1 VIN y 5915z-xx AWLYWWG EN VIN GND VOUT FLG/ADJ The NCP59150 series are high precision, very low dropout (VLDO), low ground current positive voltage regulators that are capable of providing an output current in excess of 1.5 A with a typical dropout voltage lower than 300 mV at 1.5 A load current. The devices are stable with ceramic output capacitors. This series consists of Adjustable output voltage and fixed voltage versions. The NCP59150 series can withstand up to 18 V max input voltage. Internal protection features consist of output current limiting, built-in thermal shutdown and reverse output current protection. Logic level enable and error flag pins are available on the 5-pin and 8-pin versions. The NCP59150 series Adjustable Voltage devices are available in D2PAK-5 and DFN8 packages, the Fixed Voltage option are available in D2PAK-5, D2PAK-3 and DFN8 packages. Ncy59 15z-xx ALYWG G Applications Consumer and Industrial Equipment Point of Regulation Servers and Networking Equipment FPGA, DSP and Logic Power Supplies Switching Power Supply Post Regulation Battery Chargers Functional Replacement for Industry Standard MIC29150, MIC39150, MIC37150 xx = Voltage Version y = P (NCP), V (NCV) z = 1 (Fix Voltage), 2 (Adj) A = Assembly Location L, WL = Wafer Lot Y, YY = Year W, WW = Work Week G, G = Pb-Free Package (*Note: Microdot may be in either location) ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 9 of this data sheet. Semiconductor Components Industries, LLC, 2013 May, 2013 - Rev. 1 1 Publication Order Number: NCP59150/D NCP59150, NCV59150 Series TYPICAL APPLICATIONS VIN = 3.0 V + CIN NCP59151 VOUT = 2.5 V VIN VOUT EN FLG 100k + + COUT 47 mF, Ceramic GND NCP59152 VIN CIN + CIN EN ADJ 1.3 V R1 R2 + COUT 47 mF, Ceramic Figure 2. Adjustable Regulator NCP59150 VIN VOUT GND Figure 1. Fixed 2.5 Regulator with Error Flag VIN = 3.0 V VIN VOUT = 2.5 V VOUT + COUT 47 mF, Ceramic GND Figure 3. Fixed 2.5 Regulator in D2PAK-3 Package PIN FUNCTION DESCRIPTION Pin Number D2PAK-5 Pin Number D2PAK-3 Pin Number DFN8 Pin Name Pin Function 1 - 2 EN Enable Input: CMOS and TTL logic compatible. Logic high = enable; Logic low = shutdown. 2 1 3 VIN Input voltage which supplies both the internal circuitry and the current to the output load. 3 2 1 GND Ground TAB TAB - TAB TAB is connected to ground. 4 3 6 VOUT 5 (Fixed) - 8 FLG Error Flag Open collector output. Active-low indicates an output fault condition. 5 (Adj) - 7 (Adj) ADJ Adjustable Regulator Feedback Input. Connect to output voltage resistor divider central node. - - 7 (Fixed) VOUT SENSE - - EP EXPOSED PAD - - 4, 5 NC Linear Regulator Output. Fixed Voltage Regulator Feedback Input. Connect to output voltage node. PAD for removing heat from the device. Must be connected to GND. Not internally connected. http://onsemi.com 2 NCP59150, NCV59150 Series ABSOLUTE MAXIMUM RATINGS Value Unit VIN Symbol Supply Voltage Rating 0 to 18 V VEN Enable Input Voltage 0 to 18 V VFLG Error Flag Open Collector Output Maximum Voltage 0 to 18 V VOUT - VIN Reverse VOUT - VIN Voltage (EN = Shutdown or Vin = 0 V) (Note 1) 0 to 6.5 V PD Power Dissipation (Notes 2 and 5) Internally Limited TJ Junction Temperature -40 v TJ v +125 C TS Storage Temperature -65 v TJ v +150 C 2000 200 V ESD Rating (Notes 3 and 4) Human Body Model Machine Model Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. NOTE: All voltages are referenced to GND pin unless otherwise noted. 1. The ENABLE pin input voltage must be 0.8 V or Vin must be connected to ground potential. 2. PD(max) = (TJ(max) - TA) / RqJA, where RqJA depends upon the printed circuit board layout. 3. Devices are ESD sensitive. Handling precautions recommended.. 4. This device series incorporates ESD protection and is tested by the following methods: ESD Human Body Model (HBM) tested per AEC-Q100-002 (EIA/JESD22-A114C) ESD Machine Model (MM) tested per AEC-Q100-003 (EIA/JESD22-A115C) This device contains latch-up protection and exceeds 100 mA per JEDEC Standard JESD78. 5. This protection is not guaranteed outside the Recommended Operating Conditions. RECOMMENDED OPERATING CONDITIONS (Note 6) Symbol Rating Value Unit 2.24 to 13.5 V VIN Supply Voltage VEN Enable Input Voltage 0 to 13.5 V VFLG Error Flag Open Collector Voltage 0 to 13.5 V TJ Junction Temperature -40 v TJ v +125 C 6. The device is not guaranteed to function outside it's Recommended operating conditions. http://onsemi.com 3 NCP59150, NCV59150 Series ELECTRICAL CHARACTERISTICS TJ = 25C with VIN = VOUT nominal + 1 V; VEN = VIN; IL = 10 mA; bold values indicate -40C < TJ < +125C, unless noted. Parameter Conditions Min Typ Max Unit Output Voltage Accuracy DFN package IL = 10 mA -1 1 % 10 mA < IOUT < 1.5 A , VOUT nominal + 1 VIN 13.5 V -2 2 % Output Voltage Accuracy D2PAK package IL = 10 mA -1.5 1.5 % 10 mA < IOUT < 1.5 A , VOUT nominal + 1 VIN 13.5 V -2.5 2.5 % Output Voltage Line Regulation VIN = VOUT nominal + 1.0 V to 13.5 V; IL = 10 mA 0.5 % Output Voltage Load Regulation IL = 10 mA to 1.5 A 0.02 0.2 1.0 % 175 350 mV IL = 1.5 A 300 500 mV Ground Pin Current (Note 8) IL = 1.5 A 40 60 80 mA Ground Pin Current in Shutdown VEN v 0.5 V 1.0 5.0 mA Overload Protection Current Limit VOUT = 0 V 2.0 3.0 A Start-up Time VEN = VIN, VOUT nominal = 2.5 V, IOUT = 10 mA, COUT = 47 mF 100 500 ms Output Voltage Start-up Slope Fixed Voltage Devices VEN = VIN, IOUT = 10 mA, COUT = 47 mF (Note 9) 40 200 ms/V VIN - VOUT Dropout Voltage (Note 7) IL = 750 mA ENABLE INPUT Enable Input Signal Levels Enable Pin Input Current Regulator Enable V 1.8 Regulator Shutdown 0.8 V VEN v 0.8 V (Regulator Shutdown) 2.0 4.0 mA 30 40 mA 1.0 2.0 mA 400 500 mV 6.5 V > VEN w 1.8 V (Regulator enable) 1.0 15 FLAG OUTPUT IFLG(leak) Voh = 13.5 V, Flag OFF VFLG(LO) VIN = 2.24 V, IFLG = 1 mA, Flag ON VFLG Low Threshold, % of particular VOUT 210 95 % Hysteresis, % of particular VOUT 93 2 % High Threshold, % of particular VOUT 97 99.2 % 1.240 1.252 1.265 1.259 1.271 V 200 350 nA NCP/NCV59152 ADJ VOLTAGE DEVICES ONLY Reference Voltage 1.228 1.215 1.221 1.209 DFN Package D2PAK Package Adjust Pin Bias Current 1.240 100 7. VDO = VIN - VOUT when VOUT decreases to 98% of its nominal output voltage with VIN = VOUT + 1 V. For output voltages below 1.74 V, dropout voltage specification does not apply due to a minimum input operating voltage of 2.24 V. 8. IIN = IGND + IOUT. 9. Fixed Voltage Device Start-up Time = Output Voltage Start-up Slope * VOUT nominal. Package Conditions / PCB Footprint D2PAK-3, Junction-to-Case Thermal Resistance RqJC = 2.1C/W D2PAK-5, Junction-to-Case RqJC = 2.1C/W mm2 D2PAK-3, Junction-to-Air PCB with 100 2.0 oz Copper Heat Spreading Area RqJA = 52C/W D2PAK-5, Junction-to-Air PCB with 100 mm2 2.0 oz Copper Heat Spreading Area RqJA = 52C/W DFN8, Junction-to-Air PCB with 500 mm2 2.0 oz Copper Heat Spreading Area RqJA = 75C/W http://onsemi.com 4 NCP59150, NCV59150 Series 450 450 400 DROPOUT VOLTAGE (mV) 500 400 350 300 250 200 150 100 50 0 0 0.25 OUTPUT VOLTAGE (V) 250 200 150 100 0.50 0.75 1.00 1.25 0 -50 -30 1.50 10 30 50 70 90 110 130 Figure 4. Dropout Voltage vs. Output Current (VOUTnom = 2.5 V) Figure 5. Dropout Voltage vs. Temperature (VOUTnom = 2.5 V, IOUT = 1.5 A) 3.0 0.5 A 2.5 1.0 A 1.0 1.5 A 0.8 0.6 0.4 2.0 10 mA 0.5 A 1.5 1.5 A 1.0 1.0 A 0.5 0.2 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 0 2.0 1.9 1.4 1.6 1.8 2.0 2.2 2.4 2.6 SUPPLY VOLTAGE (V) Figure 6. Dropout Characteristics (VOUTnom = 1.24 V) Figure 7. Dropout Characteristics (VOUTnom = 2.5 V) 25 1.2 GROUND CURRENT (mA) 1.4 20 15 10 5 0 1.0 1.2 SUPPLY VOLTAGE (V) 30 0 -10 TEMPERATURE (C) 10 mA 1.2 GROUND CURRENT (mA) 300 OUTPUT CURRENT (A) 1.4 0 350 50 OUTPUT VOLTAGE (V) DROPOUT VOLTAGE (mV) TYPICAL CHARACTERISTICS 0.25 0.50 0.75 1.00 1.25 1.0 0.8 0.6 0.4 0.2 0 1.50 2.8 3.0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 OUTPUT CURRENT (A) SUPPLY VOLTAGE (V) Figure 8. Ground Current vs. Output Current (VOUTnom = 1.24 V) Figure 9. Ground Current vs. Supply Voltage (VOUTnom = 1.24 V, IOUT = 10 mA) http://onsemi.com 5 NCP59150, NCV59150 Series TYPICAL CHARACTERISTICS 2.5 50 GROUND CURRENT (mA) GROUND CURRENT (mA) 60 40 30 1.5 A 20 1.0 A 0.5 A 10 0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 0.5 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 SUPPLY VOLTAGE (V) Figure 10. Ground Current vs. Supply Voltage (VOUTnom = 1.24 V) Figure 11. Ground Current vs. Supply Voltage (VOUTnom = 2.5 V, IOUT = 10 mA) 1.4 GROUND CURRENT (mA) 1.5 A 50 40 30 1.0 A 20 0.5 A 10 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 1.2 1.0 0.8 0.6 0.4 0.2 0 -50 -30 5.0 -10 10 30 50 70 90 110 130 SUPPLY VOLTAGE (V) TEMPERATURE (C) Figure 12. Ground Current vs. Supply Voltage (VOUTnom = 2.5 V) Figure 13. Ground Current vs. Temperature (VOUTnom = 2.5 V, IOUT = 10 mA, VIN = 3.5 V) 18 45 16 40 GROUND CURRENT (mA) GROUND CURRENT (mA) GROUND CURRENT (mA) 1.0 SUPPLY VOLTAGE (V) 60 0 1.5 0 5.0 4.5 2.0 14 12 10 8 6 4 35 30 25 20 15 10 5 2 0 -50 -30 -10 10 30 50 70 90 110 0 -50 -30 130 -10 10 30 50 70 90 110 130 TEMPERATURE (C) TEMPERATURE (C) Figure 14. Ground Current vs. Temperature (VOUTnom = 2.5 V, IOUT = 0.75 A, VIN = 3.5 V) Figure 15. Ground Current vs. Temperature (VOUTnom = 2.5 V, IOUT = 1.5 A, VIN = 3.5 V) http://onsemi.com 6 NCP59150, NCV59150 Series TYPICAL CHARACTERISTICS 2.60 90 70 2.55 PSRR (dB) OUTPUT VOLTAGE (V) 80 2.50 2.45 60 50 Cout = 47 mF 40 30 Cout = 100 mF 20 10 2.40 -50 -30 -10 10 50 30 70 90 0 130 110 0.01 0.1 1 10 100 1000 TEMPERATURE (C) FREQUENCY (kHz) Figure 16. Output Voltage vs. Temperature (VOUTnom = 2.5 V, IOUT = 10 mA) Figure 17. PSRR vs. Frequency, Vin = 3.5 V + 200 mVpp Modulation, Vout = 2.5 V, Iout = 0.5 A 80 70 PSRR (dB) 60 50 Cout = 100 mF 40 30 20 Cout = 47 mF 10 0 0.01 0.1 1 10 100 1000 FREQUENCY (kHz) Figure 18. PSRR vs. Frequency, Vin = 3.5 V + 200 mVpp Modulation, Vout = 2.5 V, Iout = 1.5 A 10 0.6 Vin = 2.24 V, 25C Flag Open collector output is ON 8 Vin = 2.24 V, 25C Flag Open collector output = Logic L 0.5 FLAG VOLTAGE (V) FLAG CURRENT (mA) 9 7 6 5 4 3 2 0.4 0.3 0.2 0.1 1 0 0 2 4 6 8 10 12 14 16 18 0 20 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 FLAG VOLTAGE (V) FLAG CURRENT (mA) Figure 19. Flag Current vs. Flag Voltage Figure 20. Flag Voltage vs. Flag Current http://onsemi.com 7 5.0 NCP59150, NCV59150 Series TYPICAL CHARACTERISTICS Figure 21. Line Transient Response Figure 22. Load Transient Response APPLICATIONS INFORMATION Output Capacitor and Stability Enable Input The NCP59150 series requires an output capacitor for stable operation. The NCP59150 series is designed to operate with ceramic output capacitors. The recommended output capacitance value is 47 mF or greater. Such capacitors help to improve transient response and noise reduction at high frequency. Some NCP59150 series members also feature an enable input for on/off control of the device. It's shutdown state draws "zero" current from input voltage supply (only microamperes of leakage). The enable input is TTL/CMOS compatible for simple logic interface, but can be connected up to VIN. Input Capacitor Overcurrent and Reverse Output Current Protection An input capacitor of 1.0 mF or greater is recommended when the device is more than 4 inches away from the bulk supply capacitance, or when the supply is a battery. Small, surface-mount chip capacitors can be used for the bypassing. The capacitor should be place within 1 inch of the device for optimal performance. Larger values will help to improve ripple rejection by bypassing the input of the regulator, further improving the integrity of the output voltage. The NCP59150 regulator is fully protected from damage due to output current overload and output short conditions. When NCP59150 output is overloaded, Output Current limiting is provided. This limiting is linear; output current during overload or output short conditions is constant. These features are advantageous for powering FPGAs and other ICs having current consumption higher than nominal during their startup. Thermal shutdown disables the NCP59150 device when the die temperature exceeds the maximum safe operating temperature. When NCP59150 is disabled and (VOUT - VIN) voltage difference is less than 6.5 V in the application, the output structure of these regulators is able to withstand output voltage (backup battery as example) to be applied without reverse current flow. Of course the additional current flowing through the feedback resistor divider inside the Fixed Voltage devices (30 mA typically at nominal output voltage) needs to be included in the backup battery discharging calculations. Minimum Load Current The NCP59150 regulator is specified between finite loads. A 5 mA minimum load current is necessary for proper operation. Error Flag Some NCP59150 series members feature an error flag circuit that monitors the output voltage and signals an error condition when the voltage is 5% below the nominal output voltage. The error flag is an open-collector output that can sink up to 5 mA typically during a VOUT fault condition. The FLG output is overload protected when a short circuit of the pullup load resistor occurs in the application. This is guaranteed in the full range of FLG output voltage Max ratings (see Max Ratings table). Please be aware operation in this mode is not recommended, power dissipated in the device can impact on output voltage precision and other device characteristics. Adjustable Voltage Design The NCP/NCV59152 Adjustable voltage Device Output voltage is set by the ratio of two external resistors as shown in Figure 23. The device maintains the voltage at the ADJ pin at 1.24 V referenced to ground. The current in R2 is then equal to http://onsemi.com 8 NCP59150, NCV59150 Series Thermal Considerations 1.24 V / R2, and the current in R1 is the current in R2 plus the ADJ pin bias current. The ADJ pin bias current flows from VOUT through R1 into the ADJ pin. The output voltage can be calculated using the formula shown in Figure 23. NCP59152 VIN VIN VOUT VOUT + CIN R1 EN The power handling capability of the device is limited by the maximum rated junction temperature (125C). The PD total power dissipated by the device has two components, Input to output voltage differential multiplied by Output current and Input voltage multiplied by GND pin current. P D + V IN * V OUT @ I OUT ) V IN @ I GND + The GND pin current value can be found in Electrical Characteristics table and in Typical Characteristics graphs. The Junction temperature TJ is COUT 47 mF, Ceramic ADJ GND T J + T A ) P D @ R qJA R2 (eq. 2) where TA is ambient temperature and RqJA is the Junction to Ambient Thermal Resistance of the NCP/NCV59150 device mounted on the specific PCB. To maximize efficiency of the application and minimize thermal power dissipation of the device it is convenient to use the Input to output voltage differential as low as possible. The static typical dropout characteristics for various output voltage and output current can be found in the Typical Characteristics graphs. R1 ) I ADJ @ R1 R2 Figure 23. Adjustable Voltage Operation V OUT + 1.24 V @ 1 ) (eq. 1) ORDERING INFORMATION Output Current Output Voltage Junction Temp. Range Package Shipping NCP59150DS18R4G 1.5 A 1.8 V -40C to +125C D2PAK-3 (Pb-Free) Contact Sales Office NCP59150DS25R4G 1.5 A 2.5 V -40C to +125C D2PAK-3 (Pb-Free) Contact Sales Office NCP59150DS28R4G 1.5 A 2.8 V -40C to +125C D2PAK-3 (Pb-Free) Contact Sales Office NCP59150DS30R4G 1.5 A 3.0 V -40C to +125C D2PAK-3 (Pb-Free) Contact Sales Office NCP59150DS33R4G 1.5 A 3.3 V -40C to +125C D2PAK-3 (Pb-Free) Contact Sales Office NCP59150DS50R4G 1.5 A 5.0 V -40C to +125C D2PAK-3 (Pb-Free) Contact Sales Office NCV59150DS18R4G* 1.5 A 1.8 V -40C to +125C D2PAK-3 (Pb-Free) Contact Sales Office NCV59150DS25R4G* 1.5 A 2.5 V -40C to +125C D2PAK-3 (Pb-Free) Contact Sales Office NCV59150DS28R4G* 1.5 A 2.8 V -40C to +125C D2PAK-3 (Pb-Free) Contact Sales Office NCV59150DS30R4G* 1.5 A 3.0 V -40C to +125C D2PAK-3 (Pb-Free) Contact Sales Office NCV59150DS33R4G* 1.5 A 3.3 V -40C to +125C D2PAK-3 (Pb-Free) Contact Sales Office NCV59150DS50R4G* 1.5 A 5.0 V -40C to +125C D2PAK-3 (Pb-Free) Contact Sales Office NCP59151DS18R4G 1.5 A 1.8 V -40C to +125C D2PAK-5 (Pb-Free) 800 / Tape & Reel Device For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC-Q100 Qualified and PPAP Capable http://onsemi.com 9 NCP59150, NCV59150 Series ORDERING INFORMATION (continued) Device Output Current Output Voltage Junction Temp. Range Package Shipping D2PAK-5 800 / Tape & Reel NCP59151DS25R4G 1.5 A 2.5 V -40C to +125C NCP59151DS28R4G 1.5 A 2.8 V -40C to +125C D2PAK-5 (Pb-Free) 800 / Tape & Reel NCP59151DS30R4G 1.5 A 3.0 V -40C to +125C D2PAK-5 (Pb-Free) 800 / Tape & Reel NCP59151DS33R4G 1.5 A 3.3 V -40C to +125C D2PAK-5 (Pb-Free) 800 / Tape & Reel NCP59151DS50R4G 1.5 A 5.0 V -40C to +125C D2PAK-5 (Pb-Free) 800 / Tape & Reel NCV59151DS18R4G* 1.5 A 1.8 V -40C to +125C D2PAK-5 (Pb-Free) 800 / Tape & Reel NCV59151DS25R4G* 1.5 A 2.5 V -40C to +125C D2PAK-5 (Pb-Free) 800 / Tape & Reel NCV59151DS28R4G* 1.5 A 2.8 V -40C to +125C D2PAK-5 (Pb-Free) 800 / Tape & Reel NCV59151DS30R4G* 1.5 A 3.0 V -40C to +125C D2PAK-5 (Pb-Free) 800 / Tape & Reel NCV59151DS33R4G 1.5 A 3.3 V -40C to +125C D2PAK-5 (Pb-Free) 800 / Tape & Reel NCV59151DS50R4G 1.5 A 5.0 V -40C to +125C D2PAK-5 (Pb-Free) 800 / Tape & Reel NCP59151MN18TYG 1.5 A 1.8 V -40C to +125C DFN8-4x4 (Pb-Free) 4000 / Tape & Reel NCP59151MN25TYG 1.5 A 2.5 V -40C to +125C DFN8-4x4 (Pb-Free) 4000 / Tape & Reel NCP59151MN28TYG 1.5 A 2.8 V -40C to +125C DFN8-4x4 (Pb-Free) 4000 / Tape & Reel NCP59151MN30TYG 1.5 A 3.0 V -40C to +125C DFN8-4x4 (Pb-Free) 4000 / Tape & Reel NCP59151MN33TYG 1.5 A 3.3 V -40C to +125C DFN8-4x4 (Pb-Free) 4000 / Tape & Reel NCP59151MN50TYG 1.5 A 5.0 V -40C to +125C DFN8-4x4 (Pb-Free) 4000 / Tape & Reel NCV59151MN18TYG 1.5 A 1.8 V -40C to +125C DFN8-4x4 (Pb-Free) 4000 / Tape & Reel NCV59151MN25TYG 1.5 A 2.5 V -40C to +125C DFN8-4x4 (Pb-Free) 4000 / Tape & Reel NCV59151MN28TYG 1.5 A 2.8 V -40C to +125C DFN8-4x4 (Pb-Free) 4000 / Tape & Reel NCV59151MN30TYG 1.5 A 3.0 V -40C to +125C DFN8-4x4 (Pb-Free) 4000 / Tape & Reel NCV59151MN33TYG 1.5 A 3.3 V -40C to +125C DFN8-4x4 (Pb-Free) 4000 / Tape & Reel NCV59151MN50TYG 1.5 A 5.0 V -40C to +125C DFN8-4x4 (Pb-Free) 4000 / Tape & Reel NCP59152MNADJTYG 1.5 A ADJ -40C to +125C DFN8-4x4 (Pb-Free) 4000 / Tape & Reel NCV59152MNADJTYG 1.5 A ADJ -40C to +125C DFN8-4x4 (Pb-Free) 4000 / Tape & Reel (Pb-Free) For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC-Q100 Qualified and PPAP Capable http://onsemi.com 10 NCP59150, NCV59150 Series ORDERING INFORMATION (continued) Device Output Current Output Voltage Junction Temp. Range Package Shipping NCP59152DSADJR4G 1.5 A ADJ -40C to +125C D2PAK-5 (Pb-Free) 800 / Tape & Reel NCV59152DSADJR4G 1.5 A ADJ -40C to +125C D2PAK-5 (Pb-Free) 800 / Tape & Reel For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC-Q100 Qualified and PPAP Capable http://onsemi.com 11 NCP59150, NCV59150 Series PACKAGE DIMENSIONS D2PAK 5 CASE 936A-02 ISSUE C -T- OPTIONAL CHAMFER A TERMINAL 6 E U S K B NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. TAB CONTOUR OPTIONAL WITHIN DIMENSIONS A AND K. 4. DIMENSIONS U AND V ESTABLISH A MINIMUM MOUNTING SURFACE FOR TERMINAL 6. 5. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH OR GATE PROTRUSIONS. MOLD FLASH AND GATE PROTRUSIONS NOT TO EXCEED 0.025 (0.635) MAXIMUM. V H 1 2 3 4 5 M D 0.010 (0.254) M T DIM A B C D E G H K L M N P R S U V P N G L R C SOLDERING FOOTPRINT 8.38 0.33 1.702 0.067 10.66 0.42 16.02 0.63 3.05 0.12 SCALE 3:1 5-LEAD D2PAK http://onsemi.com 12 1.016 0.04 mm inches INCHES MIN MAX 0.386 0.403 0.356 0.368 0.170 0.180 0.026 0.036 0.045 0.055 0.067 BSC 0.539 0.579 0.050 REF 0.000 0.010 0.088 0.102 0.018 0.026 0.058 0.078 5 _ REF 0.116 REF 0.200 MIN 0.250 MIN MILLIMETERS MIN MAX 9.804 10.236 9.042 9.347 4.318 4.572 0.660 0.914 1.143 1.397 1.702 BSC 13.691 14.707 1.270 REF 0.000 0.254 2.235 2.591 0.457 0.660 1.473 1.981 5 _ REF 2.946 REF 5.080 MIN 6.350 MIN NCP59150, NCV59150 Series PACKAGE DIMENSIONS D2PAK CASE 936-03 ISSUE D T C A K S B J 2 ES DETAIL C DETAIL C 3 F G SIDE VIEW 2X TOP VIEW D 0.010 (0.254) N M P R C OPTIONAL CHAMFER V H 1 U ED OPTIONAL CHAMFER T TERMINAL 4 L SIDE VIEW BOTTOM VIEW DUAL GAUGE CONSTRUCTION NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCHES. 3. TAB CONTOUR OPTIONAL WITHIN DIMENSIONS A AND K. 4. DIMENSIONS U AND V ESTABLISH A MINIMUM MOUNTING SURFACE FOR TERMINAL 4. 5. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH OR GATE PROTRUSIONS. MOLD FLASH AND GATE PROTRUSIONS NOT TO EXCEED 0.025 (0.635) MAXIMUM. 6. SINGLE GAUGE DESIGN WILL BE SHIPPED AFTER FPCN EXPIRATION IN OCTOBER 2011. SINGLE GAUGE CONSTRUCTION T M T SEATING PLANE BOTTOM VIEW DETAIL C OPTIONAL CONSTRUCTIONS SOLDERING FOOTPRINT* 10.490 8.380 16.155 2X 3.504 2X 1.016 5.080 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 13 DIM A B C D ED ES F G H J K L M N P R S U V INCHES MIN MAX 0.386 0.403 0.356 0.368 0.170 0.180 0.026 0.036 0.045 0.055 0.018 0.026 0.051 REF 0.100 BSC 0.539 0.579 0.125 MAX 0.050 REF 0.000 0.010 0.088 0.102 0.018 0.026 0.058 0.078 5 _ REF 0.116 REF 0.200 MIN 0.250 MIN MILLIMETERS MIN MAX 9.804 10.236 9.042 9.347 4.318 4.572 0.660 0.914 1.143 1.397 0.457 0.660 1.295 REF 2.540 BSC 13.691 14.707 3.175 MAX 1.270 REF 0.000 0.254 2.235 2.591 0.457 0.660 1.473 1.981 5 _ REF 2.946 REF 5.080 MIN 6.350 MIN NCP59150, NCV59150 Series PACKAGE DIMENSIONS DFN8, 4x4 CASE 488AF ISSUE C A B D PIN ONE REFERENCE 2X 0.15 C 2X 0.10 C 8X 0.08 C NOTE 4 L1 EE EE 0.15 C DETAIL A E OPTIONAL CONSTRUCTIONS EXPOSED Cu DETAIL B CCCC A (A3) A1 8 CCC EEE A1 C ALTERNATE CONSTRUCTIONS SEATING PLANE DIM A A1 A3 b D D2 E E2 e K L L1 MILLIMETERS MIN MAX 0.80 1.00 0.00 0.05 0.20 REF 0.25 0.35 4.00 BSC 1.91 2.21 4.00 BSC 2.09 2.39 0.80 BSC 0.20 --- 0.30 0.50 --- 0.15 SOLDERING FOOTPRINT* CCC C C CC 1 MOLD CMPD A3 DETAIL B D2 K CC CC EE EE TOP VIEW SIDE VIEW DETAIL A NOTES: 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.30MM FROM TERMINAL TIP. 4. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. 5. DETAILS A AND B SHOW OPTIONAL CONSTRUCTIONS FOR TERMINALS. L L 8X L 2.21 4 5 e 8X 0.63 E2 8X 4.30 2.39 b PACKAGE OUTLINE 0.10 C A B 0.05 C NOTE 3 BOTTOM VIEW 8X 0.80 PITCH 0.35 DIMENSIONS: MILLIMETERS *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5817-1050 http://onsemi.com 14 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NCP59150/D Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: ON Semiconductor: NCV59152DSADJR4G NCP59152DSADJR4G NCP59152MNADJTYG NCV59152MNADJTYG NCV59151MN30TYG NCP59151DS50R4G NCP59151MN28TYG NCV59151MN50TYG NCV59151DS25R4G NCV59151MN28TYG NCV59151MN25TYG NCP59151DS18R4G NCV59151DS30R4G NCV59151DS18R4G NCP59151DS30R4G NCP59151MN33TYG NCP59151DS25R4G NCV59151DS33R4G NCP59151MN50TYG NCV59151MN33TYG NCV59151DS50R4G NCP59151DS33R4G NCV59151MN18TYG NCP59151MN25TYG NCP59151MN30TYG NCV59151DS28R4G NCP59151DS28R4G NCP59151MN18TYG